Duronic TM61 Manual

Duronic Kabler til pc'er og periferiudstyr TM61

Læs gratis den danske manual til Duronic TM61 (4 sider) i kategorien Kabler til pc'er og periferiudstyr. Denne vejledning er vurderet som hjælpsom af 27 personer og har en gennemsnitlig bedømmelse på 4.4 stjerner ud af 14 anmeldelser. Har du et spørgsmål om Duronic TM61, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

ＣＡＵＴＩＯＮ：　ＤＯ　ＮＯＴ　ＥＸＣＥ

ＭＡＸＩＭＵＭ　ＬＩＳＴＥＤ　ＷＥＩＧＨ

ＣＡＰＡＣＩＴＹ．ＳＥＲＩＯＵＳ　ＩＮＪ

ＯＲ　ＰＲＯＰＥＲＴＹ　ＤＡＭＡＧＥ　Ｍ

ＯＣＣＵＲ！　

Power Input

100V-240V

Speed

25 mm/s

Load Capability

176 lbs / 80 kg

Motion Noise

＜55dB

RATED

●Length Adjustment Range: 100-160cm

●Height Adjustment Range: 72-120cm

●3-Level Height Memory Function

Adjust the desk upwards

Adjust the desk downwards

Height Preset 1

Height Preset 2

Height Preset 3

Press for 5 seconds, the display will show 'RES' keep pressing the key until the legs move down to

the lowest position.

To set Height Preset, press the S button until the LED Display flashes then press Preset 1, 2, 3 to

program preset.

Reset

Protection mode (auto lock screen mode)

Over-heating

Hot

E10

E20

E02

E32

E31

E60

protection

Detection

alarm

Overload

protection

Rebound

protection

Overvoltage

alarm

Undervoltage

alarm

Step out

alarm

Breaking

protection

Alarms when continuously in motion for 2 minutes.

Power back on and wait for at least 18 minutes before adjusting height again.

Alarms when motor sensor cannot be detected.

Turn off power, check the connection of motor and control box, and then power back on.

If alarm sounds when the desk is moving up, remove loads off the desk and try again.

Alarms when vibrated, collided or inclined during height adjustment. Check if there is anything

in the way of desk motion. Then proceed to the reset the motor.

If it alarms when desk is moving down, turn off the power, remove loads off the desk and re-try.

It alarms when voltage is higher than anticipated value. check the connection Turn the power off,

between power and control box. If no problem, power it back on.

It alarms when voltage is lower than required value. check the connection Turn the power off,

between power and control box. If no problem, power it back on.

It alarms when height difference between left leg and right leg exceeds the set value.

Power off first. Check whether the left leg and the right leg are in the same height. If not, re-do

Installation Step 3 to make them same height. Power it back on.

It stops and enters protection state when motor cables or manual control cables are removed

or disconnected accidentally; goes back to normal after it’s reconnected and alarm is cleared.

Engineering Mode

Chang Di plae s yed

Unit ( )

Change

Brightness (br)

Colli io Fos n rce

De ect tio (Cn F)

Long press the button, “S--”shows and flashes. Press again and the display shows “Un”.

shows “Un”.

“OFF”, Low (L), al (n) or Heavy (H) c lision force detection.Norm ol

S S

Press to save your choice.

Low (L), Normal (n) or High (H) brightness. Press to save your choice.

Long press the button, “S--”shows and flashes. Press again and the display

S S

shows “Un”. Long press the button, “S--”shows and flashes. Press again and the display

S S

Press to save your choice.

Press or to switch to “CF”. Press to select. Press or to switch between

Press or to switch to “br”. Press to select. Press or to switch between

Press to select. Press or to switch between“ ”(metric) or “ ” (imperial).

TM61 BK

TM61 WE

01 06

Cable Clip (x2)

Step 7

3-1 3-2

Connect the Control Panel to corresponding Lifting Column motor

cables and Power Adapter cables.

Use the Extension cable to connect to the motor cable on the other

side.

Plug the power adapter cable into a power outlet to start adjusting

the desk.

USB&

Type-c

Produkt Specifikationer

Mærke:	Duronic
Kategori:	Kabler til pc'er og periferiudstyr
Model:	TM61

Har du brug for hjælp?

Hvis du har brug for hjælp til Duronic TM61 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Kabler til pc'er og periferiudstyr Duronic Manualer

Duronic TM51 Manual

27 August 2024

Duronic TM61 Manual

27 August 2024

Duronic WPSLS2 Manual

27 August 2024

Duronic DMT252VX1 Manual

27 August 2024

Duronic DMT152VX1 Manual

27 August 2024

Duronic DM06-1 AO Manual

27 August 2024

Duronic DMT152 Manual

27 August 2024

Duronic ST10W Manual

27 August 2024

Duronic ST12B Manual

27 August 2024

Duronic DMHD1 Manual

27 August 2024

Kabler til pc'er og periferiudstyr Manualer

Nyeste Kabler til pc'er og periferiudstyr Manualer

Tripp Lite P580-015 Manual

3 April 2025

Wire Technologies CAB-Q-Q-100G-1M-WR Manual

2 April 2025

Wire Technologies SFP-10G-AOC-30M Manual

2 April 2025

Wire Technologies CAB-Q-Q-100G-0.5M-WR Manual

2 April 2025

Wire Technologies JNP-10G-AOC-3M-WR Manual

2 April 2025

Wire Technologies AOC-S-S-10G-10M-WR Manual

2 April 2025

Wire Technologies AOC-S-S-10G-7M-WR Manual

2 April 2025

I-Tec C31DP60HZP Manual

2 April 2025

Rocstor Y10A315-S1 Manual

1 April 2025

Lindy 38503 Manual

19 Marts 2025