Ebm-papst 4118 N/2H8P Manual

Ebm-papst Ventilator 4118 N/2H8P

Læs gratis den danske manual til Ebm-papst 4118 N/2H8P (5 sider) i kategorien Ventilator. Denne vejledning er vurderet som hjælpsom af 22 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 11.5 anmeldelser. Har du et spørgsmål om Ebm-papst 4118 N/2H8P, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/5
page 1 of 5
Operating manual
4118 N/2H8P
Product type, manufacturing date (calendar week/year of construction)
and if required, conformity mark can be found on the nameplate on the
product.
Please provide us with the contents of the nameplate when making
enquiries about the product.
ebm-papst St.Georgen GmbH & Co. KG
Hermann-Papst-Straße 1
D - 78112 St.Georgen
Phone: +49 (0) 7724 / 81-0
Fax: +49 (0) 7724 / 81-1309
info2@de.ebmpapst.com
www.ebmpapst.com
As per: 05.11.2012
Version 1 5
Article number: 9694314004
Original operating manual
INDEX
1 SAFETY REGULATIONS AND INFORMATION 1
2 INTENDED USE 3
3 TECHNICAL DATA 3
4 CONNECTION AND COMMISSIONING 3
5 FAULTS, POSSIBLE CAUSES AND REMEDIES 4
1 SAFETY REGULATIONS AND INFORMATION
Read the operating manual carefully before commencing work at the
product. Pay attention to the following warnings to avoid risk to
persons or malfunctioning.
This operating manual is an integral part of the product.
In the event of resale or change of ownership the operating manual
must accompany the product. This operating manual may be copied
and provided as information on potential risks and their avoidance.
Hazard classification of warning notices
The following risk ratings are used in this operating manual to denote
potential risk situations and important safety instructions:
DANGER
This is a potentially dangerous situation
and warns of an impending health risk
or risk of fatal injury if this warning is
not observed. Observe this warning.
WARNING
The dangerous situation can occur and
can result in major or fatal injuries if the
warning is not observed. Work with
extreme care.
CAUTION
The dangerous situation can occur and
can result in minor injuries or damage
to property if the warning is not
observed.
NOTE
A potentially dangerous situation can
occur and results in damage to
property if not avoided.
Qualification of personnel
Only skilled electricians are permitted to install the product, to carry out
the test run and to work at the electrical unit.
Only instructed and authorized skilled personnel are permitted to
transport, unpack, operate and service the product.
Basic safety regulations
Safety risks related to the product must be reassessed after installing
in the final device.
The operating manual was developed in accordance with European
market requirements and may need adapting to the market
requirements of the country in question.
When working at the product, observe the following:
Do not make any changes to the product.
WARNING
Impermissible high load
Stop the product immediately after
impermissible loading (e.g. impact,
heat, overvoltage).
page 2 of 5
Electrical voltage and current
DANGER
Electrical voltage
Regularly check the electrical
equipment of the product.
Eliminate immediately loose
connections and defective cables.
Safety and protective functions
DANGER
Missing safety device and faulty
protective equipment.
Without protective equipment severe
injuries can occur, e.g. by taking hold of
the rotating equipment.
Operate the product with protection
guards only.
Electromagnetic radiation
Electromagnetic compatibility (EMC) may affect the system integration
of the product due to interaction.
Ensure the electromagnetic compatibility of the entire system.
Moving parts
DANGER
Self-starting product
If voltage is applied, the motor
automatically restarts after a mains
failure or when blocking has been
eliminated.
Do not stand in the danger zone of
the product.
Switch off the mains voltage when
working on the product and secure
against switching on again.
DANGER
Rotating impeller
Contact with the impeller may result in
injuries.
Before starting the product, ensure
that it is securely fixed and that the
guards are in place.
DANGER
Faults in safety installations
Safety installations (e.g. smoke
detectors) may be affected by the
airflow of the product.
If necessary, provide other suitable
safety measures.
DANGER
Blocking of escape routes
The product can create dangerously
high pressure.
When operating the product ensure
that there is adequate supply and
exhaust air.
WARNING
Parts transported by the airflow
The product can transport small parts
in the airflow and catapult them out.
Ensure that there are no loose
small-parts in the intake and
exhaust area.
Do not stand in the danger zone of
the product.
WARNING
Rotating fan
Long hair, loose-fitting garments and
jewellery can be caught and pulled into
the product. Risk of injury.
Do not wear loose-fitting garments
or jewellery when working on
moving parts.
Protect long hair by wearing a hair
net.
CAUTION
High risk of fire spreading
Can cause fire to spread.
Never direct the airflow
(intake/exhaust side) at a potential
source of fire.
CAUTION
Extinguishing flames
The airflow can extinguish flames (e.g.
of a gas burner).
Do not direct the airflow
(intake/exhaust side) at an open
flame.
Hot surface
CAUTION
High temperature at motor housing.
Risk of burns
Provide adequate protection against
accidental contact.
Emission
DANGER
Acoustic alarms can be overheard.
Alarm signals can be overheard
Take technical protective measures,
e.g. optical warnings.
WARNING
A noise pressure level higher than
70dB(A) is possible depending on
the installation and operating
conditions.
Risk of deafness due to noise.
Take technical protective measures.
Provide operating personnel with
protective equipment, e.g. ear
protection.
Transport
Only transport the product in its original packaging. Secure during
transport.
The vibration values, temperature and climate ranges should not be
exceeded during transport.
Storage
Store the product in a dry and clean environment that is well protected.
Ensure that the storage temperature is adhered to,see Chapter 3,
Technical Data.If the product is not operated for a longer period of
time, we recommend running it for approx. 15 minutes annually to
move the motor bearings.

Produkt Specifikationer

Mærke: Ebm-papst
Kategori: Ventilator
Model: 4118 N/2H8P

Har du brug for hjælp?

Hvis du har brug for hjælp til Ebm-papst 4118 N/2H8P stil et spørgsmål nedenfor, og andre brugere vil svare dig


Ventilator Ebm-papst Manualer

Ebm-papst

Ebm-papst 4114 N/2H8P Manual

17 September 2025
Ebm-papst

Ebm-papst 3314 NN Manual

6 September 2024
Ebm-papst

Ebm-papst 8412 NLE Manual

3 September 2024
Ebm-papst

Ebm-papst 4118 N/2H8P Manual

3 September 2024
Ebm-papst

Ebm-papst 8218 JH4 Manual

3 September 2024
Ebm-papst

Ebm-papst 8214 JH4 Manual

3 September 2024
Ebm-papst

Ebm-papst 3412 NG Manual

3 September 2024
Ebm-papst

Ebm-papst 3214 JH4 Manual

3 September 2024
Ebm-papst

Ebm-papst 3212 JH4 Manual

3 September 2024
Ebm-papst

Ebm-papst 3218 JH4 Manual

3 September 2024

Ventilator Manualer

Nyeste Ventilator Manualer

El Corte Inglés

El Corte Inglés TF08T Manual

17 September 2025
Midea

Midea MFS18200APK Manual

17 September 2025
El Corte Inglés

El Corte Inglés FTB-M Manual

17 September 2025
Canarm

Canarm BI-16RM Manual

17 September 2025
Midea

Midea MCF23XRB Manual

17 September 2025
Canarm

Canarm ALX135-UD033EC Manual

17 September 2025
Canarm

Canarm BI-22RM Manual

17 September 2025
BriCor

BriCor ST-CF2402 Manual

17 September 2025
Canarm

Canarm ALX150-UD050EC Manual

17 September 2025
Canarm

Canarm BI-24RM Manual

17 September 2025