Ednet 91610 Manual

Ednet Lamineringssystem 91610

Læs gratis den danske manual til Ednet 91610 (4 sider) i kategorien Lamineringssystem. Denne vejledning er vurderet som hjælpsom af 24 personer og har en gennemsnitlig bedømmelse på 4.3 stjerner ud af 12.5 anmeldelser. Har du et spørgsmål om Ednet 91610, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/4
Laminator, A4
Manual
91610
The laminator is only suitable for laminating documents. Any other use or modification shall
be deemed to be improper and involves substantial risk of accidents.
Important advice about safety
1. Read through these operating instructions carefully and completely before using the
machine for the first time.
2. Only put the machine on a flat and dry surface. It must be freely accessible from all sides.
It is not recommended to use an extension cable!
3. Do not open or repair the laminating machine yourself but take it to your specialized
dealer whenever it is damaged, or contact our service hot line.
4. Only use films of the correct size (up to DIN A4 max.) and thickness (80 to 100 microns).
Films that are too thin cause a blockage of the film in the machine.
5. Do not touch the hot surface of the machine after it has started up.
6. The laminating machine is not allowed - for safety reasons - to be used by children,
unless they are supervised by an adult.
7. Never use the machine outdoor or near water.
8. Hot lamination: do not laminate in this mode any materials that are sensitive to heat
with this machine, like thermo-fax paper for example. These materials are only suitable
for cold lamination.
9. Do not pour or spill any liquid into the machine or onto it.
10. Do not insert any metal objects into the machine. Please do not grasp inside the
machine with your fingers.
11. The laminating machine is unsuitable for constant use commercially. It is recommended
to switch “O” the machine for 30 minutes, after it has been operating for a period of
approximately 30 minutes.
12. The socket should be near the device and easily accessible.
Starting up the laminating machine
1. Push the plug into the mains socket outlet and set the switch to ‘I’. The red LED (Power)
lights up and the heating process will begin.
2. The green LED (Ready) lights up after approximately 3 - 5 minutes. Now you can begin
the laminating process.
3. Open the laminating film and lay the material that is to be laminated directly onto the
closed side. Leave a margin of between 3 mm and 5 mm approximately beyond the
edges while doing so.
Caution
a) Choose a film of correspondingly suitable size in relation to the material that is to be
laminated respectively.
b) It is not recommended to process several smaller materials in one film.
c) Do not cut up the film before the laminating is done.
d) The material that is to be laminated, is not allowed to be thicker than 0.5 mm
including the film.
e) It is imperative to only laminate very thin or soft materials, like newspaper or
serviettes for example, with thicker films (100 microns). We recommend refraining
from any attempt to do so!
f) Do not insert any laminating film without the contents.
g) Never utilize laminating pockets on one side or when they are rolled up.
h) Only utilize laminating foils that are also described as such. Other kinds of film, like
transparent wallets for example, are unsuitable for laminating!
4. Insert the material within the laminating film straight and with the closed side first into
the feed opening on the machine’s front side. The material will feed it in automatically
now.
5. The laminated material that emerges from the delivery opening on the machine’s back
side is not allowed to be pulled out by force. Wait until it has run out of the machine
completely. Let the laminated material to cool down briefly!
6. Switch off the machine after the laminating has ended, by setting the switch to ‘O’. Let
the machine cool down and always pull the plug out of the mains socket outlet after
using the machine.
Note: Do not feed the laminator further with foil in case of a blockage. Turn off the device
immediately!

Produkt Specifikationer

Mærke: Ednet
Kategori: Lamineringssystem
Model: 91610

Har du brug for hjælp?

Hvis du har brug for hjælp til Ednet 91610 stil et spørgsmål nedenfor, og andre brugere vil svare dig


Lamineringssystem Ednet Manualer

Ednet

Ednet 91610 Manual

13 August 2024

Lamineringssystem Manualer

Nyeste Lamineringssystem Manualer

Exibel

Exibel L402-A Manual

2 Marts 2025
Fellowes

Fellowes Saturn 2 A3/125 Manual

12 Januar 2025
GBC

GBC Catena 65 Manual

4 Januar 2025
SEAL

SEAL 65ProMD Manual

4 Januar 2025
GBC

GBC Swingline Fusion 5000L Manual

7 Oktober 2024
Fellowes

Fellowes SPL A2 Manual

30 September 2024
Fellowes

Fellowes Halo A3/125 Manual

26 September 2024
Fellowes

Fellowes SPL A3 Manual

4 September 2024
Fellowes

Fellowes Venus2 125 Manual

2 September 2024
United Office

United Office ULG 350 A1 Manual

1 September 2024