Edwards 7005-G5 Manual

Edwards Ikke kategoriseret 7005-G5

Læs gratis den danske manual til Edwards 7005-G5 (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 10 personer og har en gennemsnitlig bedømmelse på 4.3 stjerner ud af 5.5 anmeldelser. Har du et spørgsmål om Edwards 7005-G5, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

CHESHIRE, CT 203-699-3300 FAX 860-677-7746

Installation Instructions for the

7005-G5 Hotel Room Annunciator

Description

The 7005-G5 Hotel Room Annunciator Kit alerts hearing-impaired

individuals inside a room that someone is present outside the

room. The horn/strobe is mounted inside the room. When the

pushbutton outside of the room is pressed for 5 seconds, the signal

is activated. The 7005-G5 Hotel Room Annunciator Kit contains:

Pushbutton (Cat. No. 620), Pushbutton Mounting Plate (Cat. No.

147-10), Horn/Strobe (Cat. No. 6536-G5), and Transformer (Cat.

No. 592). You can purchase each item separately from your local

Edwards distributor.

Installation

A qualified electrician familiar with National Electrical Code

and local code requirements must install this product. Failure to

follow the safety precautions in this instruction sheet could result

in product or property damage, severe personal injury or death.

WARNING

To reduce the risk of shock, do not connect AC power

until installation is complete.

WARNING

To reduce the risk of shock, do not remove lens or

tamper with unit when the circuit is energized.

Disconnect power and allow five (5) minutes for

stored energy to dissipate before starting work or

disassembly. High energy could be stored in the

strobe circuit once it is energized.

1. Install Cat. No. 620 Pushbutton and Cat. No. 147-10 mounting

plate (Figures 1 and 2)

a. Insert the back of the pushbutton through the hole in the

mounting plate. Press on the button until it is properly

seated within the hole.

b. Install a single gang 2" x 4" (51 mm x 102 mm) electrical

box using suitable hardware.

c. Extend black and white wires using 18 AWG wire and

connectors (not supplied). Route extended wires to the

horn/strobe and transformer (polarity is not important).

Ground in accordance with local codes and regulations.

d. Mount the pushbutton switch onto the electrical box

using 2 screws supplied with the Cat. No. 147-10

mounting plate.

e. If additional pushbuttons are required, follow steps a and

b above. Then, extend black and white wires using 18

AWG wire and connectors (not supplied). Route extended

wires to the previously installed pushbutton switch and

connect wire leads (Figure 1).

2. Install Catalog No. 6536-G5 horn/strobe (Figures 1 and 4).

The 6536-G5 horn/strobe can be mounted on any single gang

2" x 4" (51 mm x 102 mm) electrical box, double gang 4" x 4"

(102 mm x 102 mm) electrical box, or standard 4" x 4" (102

mm x 102 mm) junction box with a plaster ring.

a. Install an appropriate electrical box using suitable

hardware.

b. Connect one wire from the 620 pushbutton to one of the

horn/strobe wires (polarity is not important).

c. Extend the remaining horn/strobe wire to the transformer.

d. Mount the horn/strobe onto the electrical box using two

screws (supplied).

3. Install Catalog No. 592 Transformer (Figures 1 and 3).

a. Select a metal electrical box that can be grounded. Mount

the transformer onto the electrical box (Figure 3) so that

it has ground continuity to the box and conduit system.

b. Install the box using suitable hardware.

c. Ground the box in accordance with local codes and

regulations.

d. Connect the remaining pushbutton wire to one of the

terminals marked 24V 20VA.

e. Connect the horn/strobe wire to the second terminal

marked 24V 20VA.

f. Connect the transformer's primary wire leads to an

appropriate 120V AC power source.

4. When all connections are completed, press the pushbutton

and verify operability of the horn/strobe.

Maintenance

Perform regularly scheduled testing at least twice a year or more

often as dictated by local authorities having jurisdiction.

The 7005-G5 Hotel Room Annunciator is not serviceable or re-

pairable. Should it fail to operate properly, contact the supplier

for replacement.

Table 1. Specifications

Horn/strobe Voltage 24V 50/60 Hz 24V DC

Horn/Strobe Current 175 mA 125 mA

Transformer - Primary 120V

- Secondary 24V 20VA

Produkt Specifikationer

Mærke:	Edwards
Kategori:	Ikke kategoriseret
Model:	7005-G5

Har du brug for hjælp?

Hvis du har brug for hjælp til Edwards 7005-G5 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Edwards Manualer

Edwards 7005-G5 Manual

2 September 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Siemens WQ32G28IL Manual

6 December 2025

MDT BE-TA550606.02 Manual

6 December 2025

Opticis USC-CC32 Manual

6 December 2025

Audio-Technica AT33xMONO Manual

6 December 2025

Bosch SPI4EMS24E Manual

6 December 2025

Fostex P1000K Manual

6 December 2025

Advantech UTC-124I1 Manual

6 December 2025

Anton/Bauer Titon Micro Kit Manual

6 December 2025

Philips Zoom! DayWhite DIS130 Manual

6 December 2025

Opticis USB-FC30AA Manual

6 December 2025