Ei Electronics Ei407 Manual

Ei Electronics Skifte Ei407

Læs gratis den danske manual til Ei Electronics Ei407 (2 sider) i kategorien Skifte. Denne vejledning er vurderet som hjælpsom af 6 personer og har en gennemsnitlig bedømmelse på 4.8 stjerner ud af 3.5 anmeldelser. Har du et spørgsmål om Ei Electronics Ei407, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

1. INTRODUCTION

Pressing on the Ei407 Manual Call Point (MCP) black spot causes all

Alarms on Bases and Alarms to sound. ThisRadioLINK RadioLINK

informs the occupants that the building must be evacuated.

The Ei407 MCP also provides a means to test the Alarms without

having to reach up to the Alarms on the ceilings, as it can be reset

with the plastic key (supplied).

We suggest that the plastic key is mounted on a small nail under or

alongside the MCP for future use when resetting (as shown above).

2. INSTALLATION

It is recommended that you install all the other Bases / AlarmsRadioLINK

and any other RadioLINK components before installing this MCP.

All RadioLINK units should be located in their final positions before

House Coding commences.

1. The MCP should be positioned (approx) 1.2 meters high on a wall, in

a suitable location on an exit route (avoid locating near metal objects).

2. Securely attach the mounting box to the wall using the fixing screws

supplied.

3. Remove the bottom housing by first pushing in the forked end of the

key (with arrow side out) into the two slots (see Figure 1). The bottom

housing should drop down by about 10mm and expose the yellow

edge on the top of the white element (with the black spot). Remove

the key, pull the bottom housing down and then lift it up to remove

(see Figure 2).

4. Next remove the white element by lifting the lower edge (see Figure 3).

5. Connect the built-in battery by sliding the

battery switch into the “on” position. (see

Figure 4).

6. Press the House Code switch until the light

on the front turns on red ( ) (Thesee Figure 4

unit will now send out a alarm signalcoded

and the red light will flash).

7. Screw the front plate to the wall box using the

two machine screws provided (see Figure 5).

8. Now re-install the white element, yellow

edge uppermost ( ). Replace thesee Figure 6

bottom housing by lining up the two notches

and carefully pushing it flat - this should

leave it about 10mm below the bottom edge.

Now slide the bottom housing upwards (see

Figure 7). This resets the switch. The yellow

edge on the white element should now be

hidden (The unit will now send out a coded

alarm cancel signal). The red light will then

continue to flash to show it is in House Code

mode, for the next 15 minutes.

9. Immediately put all other RadioLINK

Smoke Alarms and other components into

House Code mode within 10 minutes.

10. In House Code mode, the MCP will now

send a radio message every 5 seconds. All

RadioLINK Bases and Smoke/Heat Alarms

within range that are also in House Code

mode themselves will memorise the House

Code of the MCP.

11. Check that the number of amber light

flashes (for RadioLINK Bases) or blue light

flashes (for RadioLINK Smoke Alarms)

corresponds with the number of units in the

system (e.g. Bases / Alarms plus MCP). For

example, with 3 Bases and 1RadioLINK

MCP you should see 4 amber light flashes

from each Base.

(Note: the MCP flashing red light does not

indicate the number of units in the system. It

just flashes rapidly to show it is in House

Code mode. The MCP is only an RF

transmitter and does not receive any RF

signals).

12. Remove all the RadioLINK Bases /

Alarms from House Code mode as

described in their instruction leaflets.

13. The MCP will exit the House Code mode

by itself after approx. 15 minutes without

further user intervention.

However, this could result in problems

with nearby systems if their units are

being House Coded at the same time. If

this is the case remove the MCP from its

mounting box and then from House Code

mode by pressing and holding the code

button until the red light comes on (i.e. use

the same method as to enter House Code

mode). Release the button and the red

light will go out, indicating that the MCP

has exited House Code mode. Re-

assemble and attach to box as described

previously.

Please note that this will cause the MCP

to send out a coded alarm signal which

will activate the Bases /RadioLINK

Alarms that have previously been House

Coded during the installation procedure.

3. CHECKING & TESTING THE MCP

The MCP is an important alarm device and should be tested after

installation and then weekly (and after prolonged absence) to ensure

correct operation as follows.

a) Check that the light on the front flashes green every 40 seconds.

This indicates it has power.

b) Press the black spot and the white element will drop down

exposing the yellow edge to show it is activated. The light will turn red

and stay on continuously for 3 seconds and then continue to flash red

(every 20 seconds) for 5 minutes indicating transmission of the alarm

signal (Note: after 5 minutes the RF alarm signal ceases and

therefore the smoke alarms will stop alarming. This prevents the

batteries in the MCP and the alarm from being depleted).

c) Check the RadioLINK units are now in alarm (If some or all of the

alarms have not been activated, then the House Coding procedure

should be repeated. If there are still some problems, see the

“Troubleshooting RF Link” section on page 4).

d) The MCP should be reset with the plastic key provided by pushing

the forked end (arrow side up) into the slots (see Figure 1) and pulling

the bottom housing down. Remove the plastic key. Now push the

bottom housing firmly against the back and slide upwards. This resets

the switch.The yellow strip on the white element should now be hidden.

e) If the MCP is not reset the light will flash red every 40 seconds to

remind the user to reset it.

On reset, the alarm cancel signal will be transmitted (indicated by a

single red light flash for 3 seconds).

If the light flashes amber every 9 seconds this indicates that the

batteries are depleted and the MCP will no longer be able to send an

alarm signal. The unit must be removed from its location and returned

for repair if within the guarantee period, (see sections 7 & 8 for details).

Manual Call Point

Model: Ei 407

For use with Smoke/Heat Alarms and BasesRadioLINK

House Code Button

BATTERY

ON/OFF SWITCH

Figure 1

Figure 6

Figure 7

Figure 3

Figure 2

Figure 4

12 3

Contains vital information on the product’s operation and installation.

Read and retain carefully. If you are just installing this product the

manual MUST be given to the householder.

Figure 5

A15268-R2-EI407-UC-ENG 16/8/10 11:28 AM Page 1

Produkt Specifikationer

Mærke:	Ei Electronics
Kategori:	Skifte
Model:	Ei407
Bredde:	85 mm
Dybde:	58 mm
Højde:	85 mm
Vægt:	191 g
Produktfarve:	Rød
Batteriteknologi:	Lithium
Relativ luftfugtighed ved drift (H-H):	15 - 95 %
Driftstemperatur (T-T):	0 - 40 °C
Materiale:	Glas
Forbindelsesteknologi:	Trådløs
Strømkilde type:	Batteri
Kan forbindes indbyrdes:	Ja
RF-transmissionsfrekvens:	868.5 Mhz
Mængde af sammenkoblede alarmer (maks):	12
RF-transmissionsområde:	150 m