Eldat RTS39 Manual

Eldat Ikke kategoriseret RTS39

Læs gratis den danske manual til Eldat RTS39 (1 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 22 personer og har en gennemsnitlig bedømmelse på 4.4 stjerner ud af 11.5 anmeldelser. Har du et spørgsmål om Eldat RTS39, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/1

Junction Box Transmitter RTS39

Model

RTS39E5002B01

Technical Details

Frequency: 868.3 MHz

Radiated power: 0.12 mW

Modulation: FSK

Coding: Easywave

Power supply: 230 V AC 50 Hz

Current consumption: 50 mA

Power consumption: max. 0.43 W

0.1 W stand by

Range: up to 150 m under

open eld conditions

Operating temperature: -20 °C to +60 °C

Dimensions: 48/48/25 mm

Weight: 32.0 g

Scope of Delivery

Junction box transmitter, jumper, operating

instructions

Intended Use

The Junction Box Transmitter may only be used

to operate Easywave radio receivers.

The manufacturer shall not be liable for any dam-

age caused by improper or non-intended use.

Safety Advice

Before using the device, carefully read

through the operating instructions

Caution! Electrical installation may only be

carried out by a qualied electrician!

In the electric power supply circuit to the ush-

mounted transmitter is required a suitable, eas-

ily accessible disconnecting device (e.g. auto-

matic circuit breaker).

Control unobserved never moving equipment or

electric heaters.

Note also the operating instructions of the radio

receiver.

Have faulty radio controls checked by the

manufacturer!

Do not make any unauthorized alterations or

modications to the transmitter!

Function

With the ush-mounted transmitter RTS39, the

functionality of existing switches or buttons can

be extended by a radio interface.

If a voltage is present at a switch or button, the

transmitter transmits the corresponding Easy-

wave code (A/B) to an Easywave receiver, which

then switches another device.

Caution: The connection of push-buttons is rec-

ommended only for modes with 2-button-opera-

tion!

Start-Up

1. Disconnect the electrical circuit and mount

the transmitter into a standard junction box.

Attention! Make sure there is no inter-fer-

ence with the wireless connection. Do not

mount the device in a distribution box, in met-

al casings, in direct proximity to large metal

objects, on the oor or close to it.

2. If you want to connect a switch, put the at-

tached jumper between the L and F terminals.

Factory, the transmitter is supplied to the

push-button operation (jumper not plugged).

3. Connect the power supply wires and switches

or buttons in a voltage-free state as shown in

the gures 1-3).

4. Put the lid on the junction box. Then turn o󰀨

the power supply again. Memorize the trans-

mission code in the receivers. Please read

the operating instructions supplied with the

receivers.

If the switch / button now pressed, the transmit-

ter transmits the appropriate control command to

the receiver.

SWITCH (jumper must be set between L+F)

S2 S1

230 V

S1F S2

L L

g. 1

The transmission starts on every change of state

of the switch and lasts approx. 0,5 seconds.

switch 1: input S1

close switch: --> code A1

open switch: --> code B1

switch 2: input S2

close switch: --> code A2

open switch: --> code B2

PUSH-BUTTON (no jumper between L+F)

230 V

N L S1F S2

g. 2

Transmission lasts as long as the button is

pressed but max. 36 seconds.

push-button 1 A1: input S1 --> code

push-button 2 B1: input S2 --> code

SHUTTER-CONTROL (no jumper between L+F)

230 V

AUF

N L S1F S2

g. 3

Transmission lasts as long as the button is

pressed but max. 36 seconds.

push-button A1 1: input S1 --> Code

push-button 2: input S2 --> Code B1

Programming transmitter

The RTS39 is programmed into the Easywave re-

ceiver by sending the desired transmission code

(A1 / A2 / B1 / B2).

To do this, press a connected push-button or

switch during the according step of the learning

procedure.

For more information about the learning process,

read the operating instructions of the respective

receiver.

Remote Learning

The RTS39 has a remote learning function. With

this function a built-in receiver can be brought into

learning mode or delete mode wirelessly.

If a receiver supports this feature, please refer to

its user manual.

Note that connected switching elements must be

open and a push-button must be connected nec-

essarily.

When the connected button is pressed, remote

learning telegrams are transmitted in the remote

learning function.

The jumper is used only for selection of the code

for the remote learning function, according to the

following scheme:

without jumper with jumper

S1 --> code A1

S2 --> code B1

S1 --> code A1

S2 --> code A2

For details on the remote learning function, refer

to the operating instructions of compatible recei-

vers.

Disposal

Waste electrical products and batteries not

be disposed of with household waste!

Dispose of the waste product via a col-

lection point for electronic scrap or via

your specialist dealer.

Put the packaging material into the

recycling bins for cardboard, paper and

plastics.

Warranty

Within the statutory warranty period we undertake

to rectify free of charge by repair or replacement

any product defects arising from material or pro-

duction faults.

Any unauthorized tampering with, or modica-

tions to, the product shall render this warranty

null and void.

Conformity

Hereby, ELDAT EaS GmbH declares that the ra-

dio equipment type RTS39 is in compliance with

Directive 2014/53/EU. The full text of the EU dec-

laration of conformity is available at the following

internet address: www.eldat.de

Service

If, despite correct handling, faults or malfunctions

occur or if the product was damaged, please con-

tact your retailer or the manufacturer:

ELDAT EaS GmbH

Schmiedestraße 2

15745 Wildau

Germany

Phone: + 49 (0) 33 75 / 90 37-0

Telefax: + 49 (0) 33 75 / 90 37-90

Internet: www.eldat.de

E-mail: info@eldat.de

learning

button

PTx

UM121658F_0522 DE/EN

Produkt Specifikationer

Mærke:	Eldat
Kategori:	Ikke kategoriseret
Model:	RTS39

Har du brug for hjælp?

Hvis du har brug for hjælp til Eldat RTS39 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Eldat Manualer

Eldat RTS39 Manual

31 August 2024

Eldat RTS13 Manual

31 August 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Siemens WQ32G28IL Manual

6 December 2025

MDT BE-TA550606.02 Manual

6 December 2025

Opticis USC-CC32 Manual

6 December 2025

Audio-Technica AT33xMONO Manual

6 December 2025

Bosch SPI4EMS24E Manual

6 December 2025

Fostex P1000K Manual

6 December 2025

Advantech UTC-124I1 Manual

6 December 2025

Anton/Bauer Titon Micro Kit Manual

6 December 2025

Philips Zoom! DayWhite DIS130 Manual

6 December 2025

Opticis USB-FC30AA Manual

6 December 2025