Electro Harmonix Tri Parallel Mixer Manual

Electro Harmonix Skifte Tri Parallel Mixer

Læs gratis den danske manual til Electro Harmonix Tri Parallel Mixer (11 sider) i kategorien Skifte. Denne vejledning er vurderet som hjælpsom af 42 personer og har en gennemsnitlig bedømmelse på 4.4 stjerner ud af 21.5 anmeldelser. Har du et spørgsmål om Electro Harmonix Tri Parallel Mixer, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/11
TRI PARALLEL MIXER
Effects Loop Mixer/Switcher
Congratulations on your purchase of the Electro-Harmonix Tri Parallel
Mixer! The Tri Parallel Mixer can be used in multiple configurations for a
variety of switching and mixing applications. Use it to switch between or
mix up to three separate effects loops. Send a guitar or other
instrument out to three separate amplifiers, or input three separate
instruments to switch between or mix to a single output. Mix effects in
parallel to create sounds and allow for options not possible when using
effects in series (one after another). These are a few examples of the
multiple ways to incorporate the Tri Parallel Mixer into your setup.
- USING THE TRI PARALLEL MIXER -
Plug the 9VDC adapter into the jack on the top left of the Tri Parallel
Mixer. There are multiple ways to configure your setup, the most typical
configuration is shown below: a guitar based setup for mixing and/or
switching between three separate effects loops.
WARNING: Your Tri Parallel Mixer comes equipped with an Electro-Harmonix 9.6DC-
200BI power supply (same as used by Boss® & Ibanez®: 9.6 Volts DC 200mA). The Tri
Parallel Mixer requires at 9VDC with a center negative plug. Use of the wrong 45mA
adapter or a plug with the wrong polarity may damage your Tri Parallel Mixer and void
the warranty.
In this configuration, plug your guitar or other instrument/sound source
into the INPUT jack on the right of the Tri Parallel Mixer. Connect your
amplifier or other sound destination to the OUTPUT jack on the left of
the Tri Parallel Mixer. All connections can be made using standard ¼”
instrument cables.
Connect the input of the first effect in your first effects loop to the SEND
1 jack. Connect the output of the last effect in your first effects loop to
the RTN 1 jack. Repeat this step for your other two effects loops using
the SEND 2/3 and RTN 2/3 jacks. Below is the signal path in this
configuration:
Use the CH 1/2/3 footswitches to activate their respective effects loops.
Double tap any of these footswitches to enter master bypass, which
connects the INPUT jack directly the OUTPUT jack. When in bypass,
single tap any footswitch to re-enter active mode. There are other
switching options and configuration options that will be discussed later in
this manual.
-GLOBAL CONTROLS / JACKS-
INPUT –This jack on the right of the unit is the master input for the Tri
Parallel Mixer. The signal present here will be outputted to an active
channel’s SEND jack. In master bypass, the input signal connects
directly to the OUTPUT jack.

Produkt Specifikationer

Mærke: Electro Harmonix
Kategori: Skifte
Model: Tri Parallel Mixer

Har du brug for hjælp?

Hvis du har brug for hjælp til Electro Harmonix Tri Parallel Mixer stil et spørgsmål nedenfor, og andre brugere vil svare dig


Skifte Electro Harmonix Manualer

Electro Harmonix

Electro Harmonix Triple Foot Controller Manual

14 August 2024
Electro Harmonix

Electro Harmonix Switchblade Pro Manual

7 August 2024
Electro Harmonix

Electro Harmonix Tri Parallel Mixer Manual

7 August 2024

Skifte Manualer

Nyeste Skifte Manualer

D-Link

D-Link DSS-100E-9P Manual

29 Marts 2025
Digitus

Digitus DN-80113-2 Manual

27 Februar 2025
Yamaha

Yamaha SWX2322P-16MT Manual

21 Februar 2025
HELGI

HELGI HLG0801-HDBITT Manual

30 Januar 2025
HELGI

HELGI HLG0801-4K-HDBITT Manual

30 Januar 2025
Hamlet

Hamlet HN08GTX Manual

30 Januar 2025
HELGI

HELGI HLG0414 Manual

30 Januar 2025
LogiLink

LogiLink UA0085 Manual

29 Januar 2025
Powerfix

Powerfix PSSS 2 A1 Manual

14 Januar 2025
Ebara

Ebara ServoPress LP Manual

14 Januar 2025