Elkay LKWRB1316SS Manual

Elkay Ikke kategoriseret LKWRB1316SS

Læs gratis den danske manual til Elkay LKWRB1316SS (6 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 28 personer og har en gennemsnitlig bedømmelse på 4.4 stjerner ud af 14.5 anmeldelser. Har du et spørgsmål om Elkay LKWRB1316SS, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/6

PAGE 1

4420BFDB_FTN_A LK4420BFDB_FTN_A

1000003948 (Rev. B - 03/20)

4420BFDB Fountains are among the easiest to install Fountains on the market today.

To assure you install these models easily and correctly, PLEASE READ THESE

SIMPLE INSTRUCTIONS BEFORE STARTING THE INSTALLATION. CHECK YOUR

INSTALLATION FOR COMPLIANCE WITH PLUMBING, ELECTRICAL, AND OTHER

APPLICABLE CODES. After installation, leave these instructions with the Fountain for

future reference.

Owners Manual

Models 4420BF1LDB* and 4420BF1UDB*

Bi-Level Tubular Bottle Filler Fountain with Pet fountain

INSTALLER

Models (LK)4420BF1LDB* Models (LK)4420BF1UDB*

PAGE 2

4420BFDB_FTN_A LK4420BFDB_FTN_A

1000003948 (Rev. B - 03/20)

1. This fountain is to be mounted on a smooth, at, nished surface with adequate support structure. NOTE: Mounting structure

must be capable of supporting 300 lb. load on fountain.

2. Refer to rough-in for plumbing.

3. Install shut-o󰀨 valve on water supply. (Valve not furnished)

4. Locate and install fountain using 3/8" minimum fasteners. (Fasteners not furnished)

5. Prior to installing the bottle ller to the center mounting position of fountain, insert the drain pipe (Item #15) by positioning the

short end of drain pipe through mounting plate of bottle ller. Next, place the aesthetic collar (item # 29) onto the center

mounting position of the fountain ensuring the vertical edge of the collar is upright and the curved edge sits below the mount

ing surface. Mount bottle ller to fountain with collar centered between the two pieces. Install bottle ller to fountain and secure

with supplied hardware.

6. Prior to installing the bottle ller to the arm mount of fountain, insert the drain pipe (Item #14) into the arm tunnel and adjust

drain to lean to the left side of the arm when facing the button. Next, place the aesthetic collar (Item # 29) onto the arm

mounting position of the fountain ensuring the vertical edge of the collar is upright and the curved edge sits below the

mounting surface. Mount bottle ller to arm with collar centered between the two pieces. Install bottle ller to arm being

sure drain tube is above mounting plate of ller. Install ller to fountain and secure with supplied hardware.

7. Connect water supply and fountain drain. Connect drain waste "Tee" to fountain drain tubes. Connect outlet of "Tee" to

drainage system. Water connection and drain must comply with local codes.

8. Turn on water supply and check all connections for leaks.

CAUTION: This fountain is rated for inlet water pressure of 20-105 PSI. A pressure reducing regulator should be used if the

inlet water supply exceeds 105 PSI. Any damage caused by reason of connecting this product to supply line

pressures lower than 20 PSI or higher than 105 PSI is not covered by warranty.

9. Water supply 3/8" O.D. unplated copper tube. Waste 1-1/2" IPS. Contractor to supply waste trap and service stop valve in

accordance with local code.

10. Connecting lines to be made of unplated copper and should be thoroughly ushed to remove all foreign matter before being

connected to fountain. This fountain is manufactured in such a manner that it does not in any way cause taste, odor,color,

or sediment problems.

11. Connect fountain to supply line with a shut-o󰀨 valve and install a 3/8" unplated copper water line between the valve and

the fountain. Remove any burrs from outside of water line. Push the tubes straight into the ttings until they reach a

positive stop, approximately 3/4" (See Fig. 3). DO NOT SOLDER TUBES INSERTED INTO PLASTIC FITTINGS AS

DAMAGE TO THE O-RINGS MAY RESULT.

IMPORTANT

ALL SERVICE TO BE PERFORMED BY AN AUTHORIZED SERVICE PERSON

IMPORTANT! INSTALLER PLEASE NOTE.

THE GROUNDING OF ELECTRICAL EQUIPMENT SUCH AS TELEPHONE, COMPUTERS, ETC. TO WATER LINES

IS A COMMON PROCEDURE. THIS GROUNDING MAY BE IN THE BUILDING OR MAY OCCUR AWAY FROM THE

BUILDING. THIS GROUNDING CAN CAUSE ELECTRICAL FEEDBACK INTO A FOUNTAIN, CREATING AN

ELECTROLYSIS WHICH CAUSES A METALLIC TASTE OR AN INCREASE IN THE METAL CONTENT OF THE

WATER. THIS CONDITION IS AVOIDABLE BY USING THE PROPER MATERIALS AS INDICATED. ANY DRAIN

FITTINGS PROVIDED BY THE INSTALLER SHOULD BE MADE OF PLASTIC TO ELECTRICALLY ISOLATE THE

FOUNTAIN FROM THE BUILDING PLUMBING SYSTEM.

INSTALLATION INSTRUCTIONS

Produkt Specifikationer

Mærke:	Elkay
Kategori:	Ikke kategoriseret
Model:	LKWRB1316SS

Har du brug for hjælp?

Hvis du har brug for hjælp til Elkay LKWRB1316SS stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Elkay Manualer

6 September 2024

6 September 2024

6 September 2024

5 September 2024

5 September 2024

5 September 2024

5 September 2024

Elkay LKBG2616SS Manual

19 August 2024

Elkay LKWBG2816SS Manual

19 August 2024

Elkay LKWRB1316SS Manual

19 August 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Liteline LEDBAR34 Manual

19 Juni 2025

Festo EMMB-AS-40-01-S30M Manual

19 Juni 2025

Mr Safe JS7500 Manual

19 Juni 2025

Rane SEQ 30L Manual

19 Juni 2025

XP Gold Maxx Power Manual

19 Juni 2025

Fiamma Vent 50 Manual

19 Juni 2025

Rane SEQ 30S Manual

19 Juni 2025

Parkside PRM 1800 B2 Manual

19 Juni 2025

Xiaomi Air Fryer Essential 6L Manual

19 Juni 2025

Parkside HG09673 Manual

19 Juni 2025