Elro AS80RE11 Manual

Elro Sikkerhed AS80RE11

Læs gratis den danske manual til Elro AS80RE11 (3 sider) i kategorien Sikkerhed. Denne vejledning er vurderet som hjælpsom af 18 personer og har en gennemsnitlig bedømmelse på 4.9 stjerner ud af 9.5 anmeldelser. Har du et spørgsmål om Elro AS80RE11, eller vil du spørge andre brugere om produktet?

Side 1/3
1
AS80RE11
Wireless Keyfob
Installation Instructions
General Introduction
Keyfob also incorporates a Panic switch that will immediately initiate a Full Alarm
condition when the system is Armed or Disarmed.
Product Overview
A LED indicator
B Arm
C Partial Arm
D Disarm
E Panic Switch
F Key Chain Ring
G Negative Polarity
H Positive Polarity
Binding
1.
Remove the battery cover behind the keyfob.
2.
Prepare the CR2032 coin cell battery by removing any plastic wrapping on the
battery. Do not insert the batteries yet into the unit.
3.
Log into the ELRO Smart Home Alarm account from a web browser.
4.
Select System, then Add a New Device.
5.
Select Keyfob.
6.
The following screen will appear. This means the gateway is entering binding
mode.
2
7.
Insert the battery ensuring that the +v terminal faces upwards away from the
PCB and replace the battery cover.
8.
The screen below will appear in 10 seconds if the process is successful.
9.
Time-out will occur if the binding process was unsuccessful. Please refer to the
Manual binding section.
Manual Binding
1. With the battery inserted, repeat steps 3 to 6 of the Binding with Homesys
3.
Within 5 secs, the LED indicator then stop flashing and turn off, indicating the
learning procedure is completed. The screen below will appear indicating the
process is successful.
4.
If after 30 seconds LED flashes rapidly for 3 times, it means the keyfob fails the
binding process
Operation & Testing
Operating the Keyfob
There are 5 operating modes provided by the keyfob.
1.
ARM : Press and release the ARM button.
2.
DISARM : Press and release
3.
PARTIAL ARM 1: Press and release the Partial Arm button once
4.
PANIC: Slide the Panic Switch and hold for at least 3 secs before releasing.
Note: The LED on the keyfob will turn green after button press is released. This
implies the keyfob receives a confirmation signal from the Gateway. Instead if the
LED turns red, this means the keyfob did not receive the reply from gateway
Testing the Keyfob
section.
2. Press and
hold the Disarm button for more than 3 seconds until the LED flashes
1.
Press the Arm button to see if there is an entry in the LOGS page of your
ELRO Smart Home Alarm
account.
moderately (on for 2 second; off for 2 second). This implies keyfob has now
entered the binding mode and is waiting to receive binding signals from the
gateway.
2.
Press the Partial button Arm to see if is there an entry in the LOGS page of your
ELRO Smart Home Alarm
account.
3.
Press the Disarm button to see if there is an entry in the LOGS page of your
ELRO Smart Home Alarm
account.
4.
Slide the Panic Switch and hold for at least 3 secs before releasing. See if there
is an entry in the LOGS page of your ELRO Smart Home Alarm
account.
Note: Press the Disarm button to deactivate a triggered alarm and siren sound.


Produkt Specifikationer

Mærke: Elro
Kategori: Sikkerhed
Model: AS80RE11

Har du brug for hjælp?

Hvis du har brug for hjælp til Elro AS80RE11 stil et spørgsmål nedenfor, og andre brugere vil svare dig