Emmeti CS-11 - U9310044 Manual

Emmeti Termostat CS-11 - U9310044

Læs gratis den danske manual til Emmeti CS-11 - U9310044 (2 sider) i kategorien Termostat. Denne vejledning er vurderet som hjælpsom af 22 personer og har en gennemsnitlig bedømmelse på 4.9 stjerner ud af 11.5 anmeldelser. Har du et spørgsmål om Emmeti CS-11 - U9310044, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

See overleaf for further setting up information

Sensor selection. This thermostat is a combination model allowing you to choose

between 4 different models. (A, AF,F )

A model: air only, with built in sensor

AF model: air & floo r , with both built in and remote sensor

F model: floor only, with remote sensor

Configuration Menu

Turning ON/OFF Your Thermostat

Press buttton to turn the thermostat ON or OFF. When thermostat is turned off, LCD will display OFF.

This thermostat is full of useful features which can be set quite easily through the feature configuration menu. To access the feature configuration menu, simply turn off your thermostat

and hold button M for 5 seconds. Now you can see Menu 1, to proeceed to other menu, press button M again. To exit menu, press button

Menu #

Switching differential.

Calibrate the room temperature. This feature is used to compensate for any difference

Calibrate the floor temperature. This feature is used to compensate for any difference

Set the floor temperature limit.

Set backlight turning-on time. Selecting on will turn the light on continuously.

Selecting off will turn the light off. Selecting 20 seconds will turn the light on for 20 seconds.

Select temperature format

Optimum start(preheat). This feature is to ensure that the required temperature has

already been reached when you get up in the morning or come home from work.

Select 12 / 24 hour clock

24 12 / 24

Pump protection(for hydronic heating only). In hydronic heating installations, it is

recommended to activate the pump at least 15 seconds every 24 hours in order to

avoid any seizing. Select ON to activate this feature, OFF to deactivate. When the

thermostat is activating the pump, the icon will blink.

Feature Description Factory Default

Feature Value

°C

OFF ON / OFF

ON / OFF

OFF

7_0 5_2 / 6_1 / 7_0

OFF ON / OFF

°C

°C ~

°C

20 seconds 20 seconds / ON /OFF

°C

°F

°C

A / AF / F A

Press or to select

This product should be installed by a qualified electrician.

The number of degrees difference between switching off at the

between the displayed room temperature and a thermometer.

between the displayed floor temperature and a thermometer.

This feature is to protect the floor surface.

°C or °F.

Buttons and LCD display

Buttons

Short press

Press > 5 seconds

Turning on/off thermostat

Menu button( when thermostat is turned off)

Auto/Manual mode selection

Increase the set value Bring up vacation mode

Check floor temperature (AF model only)

Decrease the set value

Lock /unlock buttons

Reset to factory settings

(when thermostat is turned off)

Set the time and week days

Cancel override( when in override mode)

Confirm settings

The buttons are locked.

Displays when heating is active

Symbol Description

Auto mode(use button M to select)

Manual mode(use button M to select)

Vacation mode

Temporary temperature override

Frost protection activated

Set temperature

The program number

Program 1,2,

3,4,5,6

AUTO

SET AT

Program type selection.

This gives user 3 options of program type.

5_2 will give you 5 days(Monday to Fiday) with the same six events(Wakeup, out, home,

6_1 will give you 6 days(Monday to Saturday) with the same six events(Wakeup, out, home,

7_0 will give you individual settings for each day from Monday to Sunday.

out, home,sleep) and 2 days(Saturday and Sunday) with the same six events.

out,home,sleep) and 1 day(Sunday) with the same six events.

Frost protection.

This feature is to avoid room temperature going below 5

°C

E0 = The internal sensor has developed a fault. You should contact your thermostat retailer for assistance.

E1 = The remote floor sensor has not been connected, has been wired incorrectly or the probe is faulty.

LO = The room or floor temperature is below 0

Error

Message

°C

HI = The room or floor temperature is above 50

°C

Program button( when thermostat is turned on)

means the thermostat will switch the heating on

0.5°C below the set temperature and

will turn it off 0.5°C above the set temperature. With a 2°C differential, the heating will switch

on 1°C below the set temperature and switch off 1°C above the set temperature.

1°C 1°C ~ 5°C

-5°C ~ +5°C

°C -5°C ~ +5°C

CS-11 LCD 7-Day 5+2 Programmable Digital Thermostat

U9310044

Registered Address: 6 Tannery Yard, Witney Street, Burford, Oxon., OX18 4DW

Tel: 01993 824900 : www.emmeti.co.uk : e: sales@emmeti.co.uk

Temporary

set temperature and on again to reach the set temperature.The default is 1°C which

To temporary override the current set temperature,

1. Press up or down button once, the set temperature starts flashing

2. Press up or down button again until the temperature you want is displayed

3. Press to confirm the setting with shown on LCD

Now your thermostat will override the current programming and maintain the new set

and hold button for 5 seconds until disappears.

Press button M to select Auto/Manual mode. In Manual mode, the thermostat maintains a constant set

temperature manually set by the user. In Auto mode, the thermostat executes the preprogrammed schedules.

To adjust these schedules, follow the easy steps below,

To set vacation mode press and hold the up button for 5 seconds until appears. Use

same procedure to exit this mode.Vacation mode

up or down button to change the set point and wait for 5

will maintain a set temperature(default

Your thermostat has the ability to reset all settings to the factory defaults. If you are

certain you want to do this: In standby mode(when thermostat is turned off), press

If thermostat is set in AF model, press and hold the down button for 5 seconds,

floor temperature will show and it will automatically revert back to room temperature

This product should be installed by

a qualified electrician.

Installation and Wiring

86mm

mm68

Rear View

45mm

13mm

27 mm

26 mm

Side View

60mm

mm68

86mm

4mm

mm7

LOAD

(16A)

FEED

(220VAC+/-15%)

Floor Sensor

(or remote air sensor)

To lock the buttons, press and hold the up and down buttons for 5 seconds until you

see a lock icon appearing, to unlock, repeat the steps above.

and hold

button M and for 5 seconds until “RES” is shown for 5 seconds on LCD.

This thermostat is fitted with a real time clock. It is essential that the clock time and day

are set accurately if you require your programmed events to start on time. Follow the

Set the Time and Day

Auto / Manual Mode

Program your thermostat

Resetting factory defaults

Lock the buttons

View floor temperature

Temporary temperature override

Vacation mode

Press the button once

Use up or down button to change the time (Hold up or down button to change

Press button again, the day of the week will flash

Press button again to accept and exit

Use up or down button to change the day of the week

Press and hold button M for 5 seconds until “Program” is shown with the Day flashing. Use up or

down button adjust the day (hold up or down button for 5 seconds to set all days the same).

Press button M again and use up or down button to set the desired temperature to be

Press button M to bring up the program 1. Use up or down button to set the start time

To skip program 2 ,3,4,5 for Saturday and Sunday, simply adjust the set temperature for program

To skip program 3 and 4, simply adjust the set temperature for program 3 and 4 to the same set

temperature as program 2.

2 ,3,4,5 to the same set temperature as program 1.

and the time will flash Step 1.

Step 2.

Step 3.

Step 4.

Step 5.

°C

) all the time. Press

Carefully separate the front half of the thermostat

from the back plate by placing a small flat head

terminal driver into the slots on the bottom face of

the thermostat

Carefully unplug the ribbon connector

which is plugged in to the front half of

the thermostat

Place the thermostat front half somewhere

safe. Terminate the thermostat as shown

in the diagrams below

Screw the thermostat back

plate on to the back box

Re-connect the thermostat ribbon cable

and clip the two halves together

(default 06:30).(Hold up or down button to change by 15 minutes each time.)

Programme Start time Setpoint

maintained for program 1.(default 21

°C

)

below easy steps,

by 15 minutes each time.)

seconds to accept and exit.

temperature until the next program period begins. To cancel the override setting, press

in 5 seconds.

CS-11 LCD 7-Day 5+2 Programmable Digital Thermostat

U9310044

Wiring Diagram

123456

SWL

Sensor

Remote

out used L

Not

230V AC

Registered Address: 6 Tannery Yard, Witney Street, Burford, Oxon., OX18 4DW

Tel: 01993 824900 : www.emmeti.co.uk : e: sales@emmeti.co.uk

“ Temporary ”

Repeat and unitl you finish the settings for 6 programmes. Press

button M to accept and exit.

The below is the default factory settings for the 6 programmes.

2 3

06:30

08:30

11:30

13:00

16:30

22:30

21°C

16°C

21°C

16°C

Note: It is faster to program the same schedule for the entire week and then to adjust the exceptional days.

1. Please ensure that the electrical wiring of the installation and connections to and from the thermostat and any remote sensor connected to it are in accordance with BS 7671, the latest edition of the IET

Wiring Regulations.

2. The thermostat must be wired to the electric mains through a switch capable of disconnecting all poles compliant with the current safety standards and with a contact separation of at least 3 mm in all poles.

3. Before commencing work on the installation, the electricity supply must be disconnected.

4. The depth of the back box should be 35mm minimum.

WARNING

Dimensions