Emphasys DC6.0 Manual


Læs gratis den danske manual til Emphasys DC6.0 (13 sider) i kategorien Højttaler. Denne vejledning er vurderet som hjælpsom af 16 personer og har en gennemsnitlig bedømmelse på 4.8 stjerner ud af 8.5 anmeldelser. Har du et spørgsmål om Emphasys DC6.0, eller vil du spørge andre brugere om produktet?

Side 1/13
Installer's Guide
EMPHASYS
Dual Channel In-Ceiling
Speakers from EMPHASYS are de-
signed to deliver crisp, full-range sound
for today’s home theater and distrib-
uted audio environments, where digital
media places extreme demands on a
speaker’s capability. But while ordinary
speakers must be used in matching pairs
for correct stereo reproduction, the
Dual Channel In-Ceiling Series models
deliver awesome stereo sound from a
single speaker. EMPHASYS engineering
has combined a dual voice coil woofer
with twin tweeters, and as a result the
Dual Channel In-Ceiling models bring
high-quality stereo audio to even the
smallest room.
DC8.5 DC6.0
Positioning the Speakers
It is best, with the Dual Channel
In-Ceiling Speaker or any other
unit, to position it so that it
aims directly toward the
listening position. This
will ensure an accurate
stereo image and
help minimize the
creation of excessive
sound reflections.
If the listening room is
very large or the ceiling
is high, the DC8.5 with its
8" aluminum woofer and greater
power handling will be preferable
to the DC6.0.
3. Mark the hole. A template for setting the hole is provided in the
box. Position the template in the desired position and outline it on
the ceiling using a pencil.
4. Cut the hole. CAUTION: This is the most important part of the
installation. If you aren’t certain whether there are any obstruc-
tions in the desired mounting area, use a drywall saw to cut a
small hole at the center of the spot you’ve outlined. Cut at a 45°
angle toward the inside of the hole. (See Diagram 2)
You can use the cutout piece to fill the hole again if obstructions
are found. Once the mounting location is deemed to be free of
obstructions, cut the outline at a 90° angle relative to the surface
of the ceiling.
5. If the area in the ceiling isn’t already insulated, add insulation
material sufficient to fill the cavity. If the insulation material used is
faced with foil or paper, position the foil or paper away from the
speaker.
CAUTION: Speaker components can get hot while playing music at
moderate to high volume levels. There should be nothing at all touch-
ing the speaker. Material in proximity to the back of the speaker must
have at a minimum 1" or 26mm clearance for non-flammable materials
and more for flammable materials like plastic vapor barriers.
Preparing the Surface for Mounting
Precautions for Installation
Careful consideration should be given to the possible presence
of electrical conduits, piping, HVAC duct work and other ele-
ments in the ceiling before the Dual Channel In-Ceiling speaker
is installed. If there is any doubt regarding the most acceptable
locations for the speakers, please consult EMPHASYS Technical
Support or the dealer.
New Construction: Unfinished Ceiling
A new construction bracket, available from your dealer, can be
installed prior to drywall application across joists (up to 24" on-
center) where a speaker will be located. After the hole is cut and
the drywall is installed, the speaker can be easily installed follow-
ing the instructions for mounting in “Finished Ceiling” below.
Note: If the speaker is to be mounted more than 24" on-center, a
special “extra-long wing” is available from your dealer.
Finished Ceiling
Prior to the actual installation of the speakers, it will be necessary
to run speaker wire to the locations in which they’ll be mounted.
See your dealer for more information. Then, with the wire in
place, the speakers can be mounted. To ensure a professional-
looking result, follow the simple steps described below:
1. Choose the general location for the installation of each speaker,
being certain that these areas present no obstructions such as
electrical conduit, HVAC duct work or water lines.
2. Find the studs nearest the desired location for the speaker.
EMPHASYS recommends the use of a good stud finder for this
procedure. If you are lining up the speakers to some other object
or molding in the room, be sure to allow for the size of the baffle,
which extends beyond the mounting hole on all four sides of the
Dual Channel In-Ceiling speaker.
Speaker Adjustments
Creating a Zone for Optimized Listening
The Dual Channel In-Ceiling speakers should be placed so that
they project, as much as possible, toward the listening position.
This will ensure an accurate stereo image and help minimize
the creation of excessive sound reflections.
If the speakers are to be mounted in a very high ceiling, the
pivoting tweeters of the DC8.5 should be aimed directly toward
the listening position. (See Diagram 1)
In other cases it might be preferable to aim the tweeters slightly
outward, away from the listening position.
CAUTION: The tweeter dome, whether aluminum or silk, can be
damaged through direct contact with fingers or objects. Please be
careful when installing and adjusting the speaker.
Diagram 1:
Tweeters
Push Tweeters Here
2
Diagram 2:
Ceiling Cutout


Produkt Specifikationer

Mærke: Emphasys
Kategori: Højttaler
Model: DC6.0

Har du brug for hjælp?

Hvis du har brug for hjælp til Emphasys DC6.0 stil et spørgsmål nedenfor, og andre brugere vil svare dig




Højttaler Emphasys Manualer

Emphasys

Emphasys DC6.0 Manual

15 September 2024
Emphasys

Emphasys IW6.0 Manual

19 Juli 2024
Emphasys

Emphasys IC6.0 Manual

19 Juli 2024

Højttaler Manualer

Nyeste Højttaler Manualer