EnGenius N900 Manual

EnGenius Adgangspunkt N900

Læs gratis den danske manual til EnGenius N900 (1 sider) i kategorien Adgangspunkt. Denne vejledning er vurderet som hjælpsom af 122 personer og har en gennemsnitlig bedømmelse på 4.6 stjerner ud af 61.5 anmeldelser. Har du et spørgsmål om EnGenius N900, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/1

Quick Installation Guide

Maximum data rates are based on draft IEEE 802.11ac and IEEE 802.11 standards. Actual

throughput and range may vary depending on many factors including environmental

conditions, distance between devices, radio interference in the operating environment, and

mix of devices in the network. Features and specications subject to change without notice.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following

two conditions: (1) this device may not cause harmful interference, and (2) this device must

accept any interference received, including interference that may cause undesired operation.

Trademarks and registered trademarks are the property of their respective owners. For United

NotesTechnical Support

Country of Purchase Service Center Service Information

North America

www.engeniuscanada.com

Canada rma@engeniuscanada.com

Toll Free: (+1) 888 397 2788

Local: (+1) 905 940 8181

www.engeniustech.com Los Angeles, USA support@engeniustech.com

Toll Free: (+1) 888 735 7888

Local: (+1) 714 432 8668

Central & South America

es.engeniustech.com

pg.engeniustech.com

Miami, USA miamisupport@engeniustech.com

Miami: (+1) 305 887 7378

Sao Paulo, Brazil: (+55) 11 3957 0303

D.F, Mexico: (+52) 55 1163 8894

Europe

www.engeniusnetworks.eu

Netherlands support@engeniusnetworks.eu

(+31) 40 8200 887

Africa

CIS

Middle East

Russia

www.engenius-me.com

Dubai, UAE support@engenius-me.com

Toll Free:

U.A.E.: 800-EnGenius

800-364-364-87

General: (+971) 4 357 5599

Asia

Oceania

www.engeniustech.com.sg

Singapore www.engeniustech.com.sg/e_warranty_form

techsupport@engeniustech.com.sg

Toll Free:

Singapore: 1800 364 3648

Others

www.engeniusnetworks.com

Taiwan, R.O.C technology@senao.com

EWS310AP

EWS320AP

EWS360AP

version l.0

Dual Band Wireless Managed Indoor Access Point

Package Contents

A) Congure Managed AP(s) through the GUI interface from the switch

for WLAN settings under Device Management.

B) Add Managed AP(s) to specic to save repetitive AP Cluster

conguration tasks.

C) Users may create several clusters simultaneously to accommodate

their deployments under AP Clusters.

D) For distinct settings, EnGenius Wireless Management switches still oer

individual Managed Access Point customization for cluster members

such as dierent channels that best adapt your local WLAN deployments.

E) Upon successful connection and setup, user can go through dierent

sections on the web management pages to unleash Managed AP’s full

features for your WLAN deployment and performance monitoring.

4 Adding Managed AP

(Through EnGenius Wireless Management Switch GUI)

5ConguringManagedAP

(Through EnGenius Wireless Management Switch GUI)

1 Connecting the Access Point

(Through EnGenius Wireless Management Switch)

2IPAddressConguration

Minimum Requirements

+ Broadband Internet Service

(Cable or DSL Modem)

+ Internet Browser

(Internet Explorer, Safari, Firefox, Chrome)

+ EnGenius Wireless Management L2 Switch

(To use with EWS Series Management Switches)

Managed Indoor

Access Point

Power Adapter RJ-45 Ethernet Cable

Mounting Bracket Mounting Kit T-Rail Mounting Kit

A) All Managed AP(s) connected to the same network as the Wireless

Management Switch will appear on the right side of the screen, under the

Access Point Under Approval list. Locate and select the Managed AP by

checking the box and click Allow to manage the device.

B) You may congure your Managed AP(s) after you successfully

connected to the Wireless Management Switch through its GUI.

A) Connect one end of the into an on the Ethernet Cable Ethernet Port

front panel of the EnGenius Wireless Management Switch and the other

end to the Ethernet Port on the computer.

B) Connect another into the of the Managed AP Ethernet Cable LAN Port

and the other end to the on the Wireless Management Ethernet Port

Switch. With the Wireless Management Switches, the Managed AP is able

to obtain proper assigned IP address for further congurations.

B A

PoE Wireless Management Switch

Wall or Ceiling

Mounting Screw

Mounting

Bracket

Short Screw

Access

Point

Long Screw

To attach the AP to a ceiling using T-Rail connectors:

A) Attach the T-rail connectors to the bottom cover of the AP

using the provided short screws. Use appropriate size T-rail

connectors (15/16” or 9/16”). If extra space

is required to accommodate drop ceiling tiles,

use the provided spacers and long screws.

T-Rail

Connector

T-Rail

Connector

Spacer

The AP can be ceiling mounted or wall mounted depending on the setup.

To attach the AP to a ceiling or wall using the mounting bracket:

A) Attach the mounting bracket to the wall or ceiling using the provided

mounting kit.

B) Insert the provided short screws into the mounting holes. Make sure

there’s enough space between the screws and unit for the mounting

bracket. If extra space is

required, use the provided

spacers and long screws from

the T-Rail mounting kit.

C) Mount the AP to the mounting

bracket by rotating the unit

clockwise about 90 degrees

to secure it in place.

B) Line up the connected T-rail connectors

with an appropriately sized rail and

press the unit onto the rail until it

snaps into place.

Note: To protect your Access Point, use the Kensington security slot to attach

a cable lock (cable lock is not included).

Mounting the Access Point

T-Rail

* Your model number may

be dierent in the web

browser interface.

* Your model number may be dierent in the web browser interface.

A) Ethernet cable Connect one end of the into the of the LAN port

Access Point and the other end to the on the computer.Ethernet port

B) Power Adapter Connect the to the of the Access Point DC-IN port

and plug the other end in to an electrical outlet.

Note: The Access Point supports both PoE (Power over IEEE 802.3at

Ethernet) or the included power adapter. You may use either one as the

power source. DO NOT use both at the same time.

A) Once your computer is on, ensure

that your TCP/IP is set to or On

Enabled. Open Network

Connections and then click Local

Area Connection Internet. Select

Protocol Version 4 (TCP/IPv4).

B) If your computer is already on a

network, ensure that you have

set it to a Static IP Address on the

interface.

(Example: 192.168.1.10 and the

Subnet Mask address as

255.255.255.0.)

1 Connecting the Access Point

A) Open a web browser on your

computer. In the address bar of the

web browser, enter 192.168.1.1

and enter.

3 Access Point Setup

A) Open a web browser on your computer. In the address bar of the web

browser, enter and 192.168.0.239 enter.

B) A login screen will appear. By default, username is and the admin

password is . Enter the current username and password of password

the Wireless Management Switch and then click Login.

3 Management Switch Setup

A) Once your computer is on, ensure

that your TCP/IP is set to or On

Enabled. Open Network

Connections and then click Local

Area Connection Internet. Select

Protocol Version 4 (TCP/IPv4).

B) If your computer is already on a

network, ensure that you have

set it to a Static IP Address on the

interface.

(Example: 192.168.1.10 and the

Subnet Mask address as

255.255.255.0.)

Managed Access Point Installation with Wireless Management Switch

Stand-alone Access Point Installation

C) The EnGenius Wireless Management Switch User Interface will appear.

Make sure the is set to Controller State Enabled.

C) The EnGenius Access Point User Interface will appear. This device can

operate in the following modes: Access Point, WDS AP and WDS Bridge.

Switch modes by selecting the Operation Mode under “Network”,

“Wireless” tab.

B) A login screen will appear. By default,

the username of the Access Point

is and the password is admin admin

Enter the current username and

password of the Access Point and

then click . Login

Produkt Specifikationer

Mærke:	EnGenius
Kategori:	Adgangspunkt
Model:	N900
Vekselstrømsindgangsspænding:	100 - 240 V
Vekselstrømsindgangsfrekvens:	50 - 60 Hz
Bredde:	161.54 mm
Dybde:	161.54 mm
Højde:	41.6 mm
Vægt:	362.8 g
Produktfarve:	Hvid
Opbevaringstemperatur (T-T):	-20 - 60 °C
Relativ luftfugtighed ved drift (H-H):	0 - 90 %
Relativ luftfugtighed ved opbevaring (H-H):	0 - 90 %
Ethernet LAN-porte (RJ-45):	1
Driftstemperatur (T-T):	0 - 50 °C
Ethernet LAN-datahastigheder:	10,100,1000 Mbit/s
Sikkerhedsalgoritmer:	802.1x RADIUS, EAP-MD5, EAP-TLS, EAP-TTLS, SNMP, SSID, WPA, WPA-AES, WPA-EAP, WPA-PSK, WPA-TKIP, WPA2, WPA2-AES, WPA2-TKIP
Intern hukommelse:	64 MB
Kabler inkluderet:	LAN (RJ-45)
Frekvensområde:	40 Mhz
Certificering:	FCC, IC
Strømforbrug (maks.):	18.2 W
Placering:	Table, Wall
Netværksstandarder:	IEEE 802.11a, IEEE 802.11b, IEEE 802.11g, IEEE 802.11n, IEEE 802.1D, IEEE 802.1Q, IEEE 802.3at
DC-in-stik:	Ja
DHCP-klient:	Ja
DHCP-server:	Ja
Antenner, antal:	6
Webbaseret administration:	Ja
Knap til nulstilling:	Ja
Servicekvalitet support (QoS):	Ja
IP-adresse filtrering:	Ja
LED-indikatorer:	Ja
AC-adapter inkluderet:	Ja
Harmoniseret systemkode (HS):	85176990
Frekvensbånd:	2.4 - 5 GHz
Intern:	Ingen
Maksimal dataoverførselshastighed:	450 Mbit/s
Modulation:	64-QAM, BPSK, CCK, DBPSK, DQPSK, OFDM, QPSK
Wi-Fi-datahastighed (maks.):	450 Mbit/s
Indgangsstrøm:	2 A
Firmware kan opgraderes:	Ja
Flashhukommelse:	16 MB
Strøm over Ethernet (PoE):	Ja
Antal kanaler:	11 kanaler
Switch-type:	Administreret
VLAN understøttelse:	Ja
Filtrering af MAC-adresser:	Ja
Administrationsprotokoller:	SNMP v1/v2c, MIB I/II
2.4 GHz:	Ja
5 GHz:	Ja
WAN-forbindelse:	Ethernet (RJ-45)
Antennefunktioner:	Integreret antenne
Antal SSID understøttet:	16
Niveau for antennestyrke (maks.):	5 dBi
Wi-Fi-multimedie (WMM)/(WME):	Ja
Transmissionseffekt:	15 dBmW
Driftsmodus:	Access Point (AP)