Esotec Siena Manual

Esotec Ikke kategoriseret Siena

Læs gratis den danske manual til Esotec Siena (5 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 108 personer og har en gennemsnitlig bedømmelse på 3.8 stjerner ud af 54.5 anmeldelser. Har du et spørgsmål om Esotec Siena, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/5

Instruction manual

Solar pond pump set

Napoli LED, Napoli LED top and Siena LED

These instructions relate ONLY to this product and contain important informa-

tion for using the product for the first time. Please keep these instructions for

later reference and should always accompany the product in the event of trans-

ference to a new user.

1. Introduction

Dear Costumer, thank you for purchasing the solar pump kit.

With this solar pump kit you purchased a product manufactured according to the cur-

rent state of technology.

This product fulfils all requirements of the valid European and national regula-

tions. The conformity was proved. The relevant declarations and documentati-

on are deposited with the manufacturer.

To maintain this state and guarantee a safe operation, you as the user will have to fol-

low this operating manual!

2. Safety Instructions

- In case of damages caused by not following

this operating manual, the warranty rights

will expire! We exclude liability for any

consequential damages!

- We exclude liability for property or

personal damages caused by inappropriate

handling or not following the safety instructions.

- In these cases any guarantee rights will expire.

Due to safety and admission reasons (CE) it is not allowed to arbitrarily reconstruct

and/or change the solar pump kit.

Therefore, please keep to the operating manual.

The accident prevention rules of the association of the industrial trade cooperative

association for electric plants and working material are to be considered in industrial

environments

3. Appropriate Use

- The pumping system is designed for the outdoor use in garden ponds. The accu-

mulator storage is charged during sunshine. The solar pump may be switched

“on” “off”and via a switch. An LED-display informs you about the charge condi-

tion of the accumulator.

- Direct solar radiation is required for the correct function.

- The pumping system is characterized by its easy assembly. Tools are not requi-

red for the assembly.

- The pump must not be used for the raising of drinking water.

- The performance may be adjusted via a controller on the pump.

- In order to avoid any disturbing gurgling, simply attach fewer standpipes to the

pump.

- In order to safely interrupt the pumping it is required to interrupt the cable connec-

tion between solar module and pump.

4. Assembly/installation and start of operation

For the details of assembly/installation and start of operation, please see the instruc-

tion manuals of the accumulator box and the pond pump.

5. Service and Maintenance

In order to preserve the performance of the pump, it is required to wash out the pump

and its parts with warm water depending on the pollution of the water.

For directions for the service and maintenance of the pump and accumulator storage,

please see the instruction of the pump and accumulator storage.

Occasionally wipe the solar module clean with a soft and slightly moistened cloth.

Note: Before carrying out operations on the pump, interrupt the plug connection bet-

ween pump and battery pack in order to avoid any unintentional starting during the

operations.

6. Technical Data

Solar pumping system Napoli LED Napoli LED top Siena LED

- System voltage: 12 -24 VDC 12 -24 VDC 12 -24 VDC

Solar module

- Nominal power: 10 Wp 20 Wp 20 Wp

- Nominal voltage: 17,5 V 17 V 17 V

- Nominal current: 580 mA 1,2 A 1,2 A

- Open-circuit voltage: 21,6 V 21 V 21 V

- Short-circuit current: 680 mA 1,32 A 1,32 A

- Projection system: IP 65 IP 65 IP 65

- Temperature range: -30°C to +75°C -30°C to +75°C -30°C to +75°C

- Dimensions: 440 x 255 x 25 mm 530 x 360 x 25 mm 530 x 360 x 25 mm

Water pump:

- Operating voltage: 12 to 24 V DC 12 to 24 V DC 12 to 24 V DC

- Power consumption (12/24V): 3 W/ 12 W 3 W/ 12 W 5 W/ 22 W

- Max. delivery height (12/24V): 0,8 m/ 2 m 0,8 m/ 2 m 0,9 m/ 2,8 m

- Delivery rate (12/24V): 470 l/h/ 750 l/h 470 l/h/ 750 l/h 900 l/h/ 1500 l/h

- Protection system: IP 68 IP 68 IP 68

- Temperature range: +4 to +40°C +4 to +40°C +4 to +40°C

- Dry running: dry protected dry protected dry protected

Accumulator storage:

- Accumulator (lead gel): 12V/ 7Ah 12V/ 7Ah 12V/ 7Ah

- Output voltage: 12 to 24 VDC 12 to 24 VDC 12 to 24 VDC

- Runtime with fully charged

accumulator: max. 13 h max. 13 h max. 6 h

- Max. module capacity: 20 Wp (36 cells) 20 Wp (36 cells) 20 Wp (36 cells)

- Max. output current: 800 mA 800 mA 800 mA

Attention: Do not put the housing into the blazing sun! Overheating risk!

LED Light ring:

- Illuminants: 6 LEDs 6 LEDs 6 LEDs

- Operating voltage: 12 to 24 VDC 12 to 24 VDC 12 to 24 VDC

- Protection class: IP 68 IP 68 IP 68

- Operating temperature range: +4 to +40°C +4 to +40°C +4 to +40°C

Note: Protect the pump from frost!

In cold winter months, it is required to take the pump out of the water and store it in

a warm place. The solar module may be left outside during the winter.

7. Safety Instructions:

DANGER for children! Keep children away from swallowable small parts (ascending

pipe and sprinklers) and the packaging material. Danger of suffocation!

WARNING: risk of stumbling! Lay the connecting cable so that it will not become a

trip hazard!

CAUTION Material damage! When setting up the solar module without module brak-

ket, please pay attention to an adequate stability. The solar module may be damaged

in case of tipping or in case of an impact of a foreign object.

Disposal instruction for electric appliances:

Dear customer, if you want to get rid of the article, please dispo-

se it according to the current regulations. The municipal authori-

ty will provide you with information.

Manufacturer:

esotec GmbH

Gewerbegebiet Weberschlag 9

D-92729 Weiherhammer

Tel.-Nr: +49 (0)9605-92206-28

Fax.-Nr: +49 (0)9605-92206-10

e-mail:info@esotec.de

Internet: www.esotec.de

Additional parts:

5 m extender cable for water pump and solar module: 101738

5 m extender cable for fountain light: 101740

Customer support:

If you have problems or questions regarding this product, simply contact us!

Monday to Friday 8 am to 12 noon and 1 pm to 4 pm.

By phone: 09605-92206-27

By e-mail for ordering spare parts: ersatzteil@esotec.de

By e-mail for questions about the product: technik@esotec.de

Product manufacturer item No.:

solar pump system Napoli LED: 101773

solar pump system Napoli LED top: 101776

solar pump system Siena LED: 101780

Operating manual

These instructions relate ONLY to this product and contain important informa-

tion for using the product for the first time. Please keep these instructions for

later reference and should always accompany the product in the event of trans-

ference to a new user.

1. Introduction

Dear Costumer,

Thank you for purchasing the solar light. With this solar light you purchased a product

manufactured according to the current state of technology.

This product fulfils all requirements of the valid European and national regula-

tions. The conformity was proved. The relevant declarations and documentati-

on are deposited with the manufacturer.

To maintain this state and guarantee a safe operation, you as the user will have to fol-

low this operating manual!

2. Safety Instructions

- In case of damages caused by not

following this operating manual, the

warranty rights will expire! We exclude

liability for any consequential damages!

- We exclude liability for property or

personal damages caused by inappropriate

handling or not following the safety instructions.

- In these cases any guarantee rights will expire.

Due to safety and admission reasons (CE) it is not allowed to arbitrarily reconstruct

and/or change the solar light.

Therefore, please keep to the operating manual.

The accident prevention rules of the association of the industrial trade cooperative

association for electric plants and working material are to be considered in industrial

environments.

3. Intended use

This submersible pump is designed for pumping water in garden ponds, fountains,

water dishes, etc. It can pump water through a hose connection or can be operated

through attached lifting tubes with water sprinklers.

A solar module or a power pack with a voltage of 12 to 24 volts can be used as the

energy source. When used with a solar module, the pump works only if enough

solar radiation strikes the solar module.

A battery box (accessory) is delivered along with this pump. When battery is on, an

LED light (accessory) can be attached to the lifting tube. This gives the fountain a

decorative lighting. The LED light rings are available in different colours.

The delivery rate of the pump can be adjusted using the regulator on the front side

of the pump. The water pump has no On/Off switch. As soon as the pump is con-

nected to its power supply, it starts pumping water.

4. Installation and commissioning

1. Roll out the connecting cable of the

pump completely.

2. Ensure that the cap is firmly in place on

the socket.

3. Place the pump in water (please note

Point 5 here).

4. Connect the lifting tubes till they project

out of the water surface. For this, first

attach the reducer to the pump.

5. You can now choose from 2 different

water nozzles.

6. Alternatively, the pump can also be used

for pumping water through a hose. For

this, you just have to attach a hose to the

pumpʼs pipe.

7. Now supply power to the water pump

through a solar module. Use the enclo-

sed plug with cable (red = positive pole,

black = negative pole) for this. If you

have purchased this pump as a complete

solar power system, then the appropriate

plug is already attached to the solar module.

Note: The plug has reverse-polarity protection, no force should be used while inser-

ting. The glass of the solar module is fragile.

Caution! Risk of injury! A broken module cannot be repaired again and must be dis-

posed off in an environmental-friendly way.

8. If the pumping capacity is too high, you can reduce the amount of water. Simply

turn the regulator on the front side of the pump in clockwise direction. Please

do not use force while adjusting. The adjustment range is 45°.

4.1 Operation with LED light ring

The accessories include a LED light ring. This light ring can be easily slipped onto

the lifting tube.

Electrical connection is established via the socket on the pump. For this, remove

the drain plug, insert the light ring plug in the socket and tighten the cap nut firmly.

5. Dry run protection

The pump is equipped as standard with a dry run protec-

tion. Two sensor points are provided on the side of the

housing for this. The pump works if these points are

under water. If a point projects out of the water, the pump

does not work.

6. Care and maintenance

For optimum performance of the pump, it must be washed occasionally with warm

water depending on the water contamination. To wash the pump, open the housing

as follows:

Note: Please do not use force while dismantling or assembling the pump. The parts

are very fragile and can break easily.

1. Disconnect the pumpʼs plug.

2. Pull the front cover of the pump forward like a slide gently (Figure 1).

3. Turn the front cover of the pump by about 45° clockwise (Figure 1) and carefully

pull the cover forward (Figure 2). Watch out for the plastic shaft and the seal while

doing this.

4. Carefully drag the impeller out of the pump (if necessary, use pliers). (Figure 3).

5. Now clean all the parts carefully with warm water.

6. Then plug the shaft with the impeller carefully into the hole of the pump. Ensure

that the shaft is fitted firmly.

7. Now place the cover carefully over the pump. Ensure that the seal is fitted proper-

ly.

8. Turn the front cover again by 45 degrees counter-clockwise into the starting posi-

tion.

9. Slide the lower part of the pump completely into the pump housing.

The pump is ready to use again.

7. Malfunction

Pump is not pumping water

- Is the pump completely submerged in water? Dry run protection (Point 5)

- Is the polarity of the supply voltage reversed? Cable colour brown = + pole,

blue = negative pole

- Is the pump dirty? Cleaning the pump, see Point 6.

8. Technical data

Operating voltage: 12 - 24 V DC

Degree of protection: IP 68

Power consumption: Approx. 5 W at 12 VDC - approx. 22 W at 24 VDC

Pump lift: Max. 0.9 m at 12 VDC - max. 2,8 m at 24 VDC

Delivery rate: Max. 900 l/h at 12 VDC - max. 1500 l/h at 24 VDC

Operating temp. range: +4 to +40°C

Note: The pump is only suitable for pumping water.

Note: Protect the pump from frost!

During cold winter months, the pump must be taken out of the water and

placed/stored in a warm area. The solar module can spend the winter outdoors.

Sensorpoints

lifting tubes

water nozzle

lifting tubes

Customer support:

If you have problems or questions regarding this product, simply contact us!

Monday to Friday 8 am to 12 noon and 1 pm to 4 pm.

By phone: 09605-92206-27

By e-mail for ordering spare parts: ersatzteil@esotec.de

By e-mail for questions about the product: technik@esotec.de

Product: Manufacturer Item No.: 101758

turn 45°

Drain plug

Light ring

connection

Produkt Specifikationer

Mærke:	Esotec
Kategori:	Ikke kategoriseret
Model:	Siena

Har du brug for hjælp?

Hvis du har brug for hjælp til Esotec Siena stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Esotec Manualer

Esotec Palermo LED Manual

22 August 2024

Esotec Siena Manual

22 August 2024

Esotec Palermo Manual

22 August 2024

Esotec Rimini Plus Manual

22 August 2024

Esotec Palermos-S Manual

22 August 2024

Esotec Garda Manual

22 August 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

IStorage FlashTrust Manual

28 September 2025

Dorr SLR-13 Manual

28 September 2025

Steinberg SpectraLayers One 8 Manual

28 September 2025

Yadea Elite Max Manual

28 September 2025

Mercyu MRU-137 Manual

28 September 2025

IStorage Kanguru SS3 Manual

28 September 2025

ROCWARE RC18 Manual

27 September 2025

Advantech UNO-137 Manual

27 September 2025

ROCWARE RC08 Manual

27 September 2025

Stiebel Eltron CON 20 ZS Manual

27 September 2025