ETI Thermapen Mk4 Manual

ETI Madtermometer Thermapen Mk4

Læs gratis den danske manual til ETI Thermapen Mk4 (4 sider) i kategorien Madtermometer. Denne vejledning er vurderet som hjælpsom af 35 personer og har en gennemsnitlig bedømmelse på 4.9 stjerner ud af 18 anmeldelser. Har du et spørgsmål om ETI Thermapen Mk4, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/4
Congratulations
The new Super-Fast Thermapen Mk4 is a precision thermometer used for many applications,
including cooking. With proper care, it will offer accurate measurements for many years. The
new Mk4 Thermapen includes several new features, including: intelligent backlight, auto-
rotating display, user-selectable sleep interval, motion-activated wake-up mode, and added
water resistance.
Instrument Operation
The unit is switched on by unfolding the thermocouple probe
until the display comes on. Conversely, the unit is turned
off by folding the probe away and lightly pressing the tip
into the rubber probe retainer located at the bottom rear of
the instrument. It is recommended to store the probe in the
closed position when not in use.
Do not force the probe further than 180° when opening
or damage to the rotating hub may occur.
The micro-thermocouple sensor is located at the tip of the probe shaft. Minimum immersion
is only 1/8" (3 mm). For best results, immerse or penetrate the probe into the food item so the
probe tip is in the place you want to measure. In food, this should normally be at the center
of the thickest part.
The Thermapen will read to within 1°F of the actual
temperature of an ice bath within three seconds. Reading
times in other foods may vary slightly.
Do not immerse the probe all the way to the plastic
rotating hub. Avoid getting flour, moisture, or oil on the
hub itself. Although there is an O-ring seal, oils can
work their way past the seal and accumulate inside
the hub and may cause failure. The probe tip is sharp.
Use caution to avoid injury. Do not “stab” the material
to be measured. Use steady force to penetrate meats
or semi-solids. Avoid bone. Do not lift or flip heavy
meats with the probe tip. The probe shaft is hollow and
contains a sensor. If bent, it may fail.
Rotating hub
Probe Tip
Sensor location
Minimum immersion 1/8"
Thermapen® Mk4
Operating Instructions
Instrument Configuration
You can personalize your Thermapen by changing several factory default settings including:
Temperature display from °F to °C
Display resolution from 1° to 1.0°
Screen Rotation
Auto-Off/Sleep Mode
To change any of these settings,
loosen the battery cover screw using
a Phillips screwdriver and remove the
battery cover. Open the probe to turn
the unit on. The Thermapen Mk4 has
two small buttons inside the battery
compartment: MENU, which is used
to enter, save settings, and exit the menu; and SET, which is used to select desired settings.
Settings are saved once ‘END’ is displayed at the end of the menu options. To abort settings,
close the probe. Press the MENU button to cycle through the following settings:
Temperature Display Units, °F to °C
Press the MENU button until ‘C or F’ is displayed. Press SET to toggle between
‘°F’ and ‘°C’ as displayed in the upper right hand corner of the display. When the
selection is complete, press MENU to store setting.
Display Resolution, 1° to 1.0°
Press the MENU button until the current resolution setting ‘0.1°’ or ‘1°’ is
displayed. Press SET to toggle between ‘0.1°’ and ‘1°’. When the selection is
complete, press MENU to store setting.
Screen Rotation
Press the MENU button until ‘DISPLAY’ is shown at the top of the display. Press
SET to select ‘360°’ for full 4-way rotation, ‘180°’ for 2-way rotation (horizontal
only), or choose to lock the display in a specific orientation when ‘Loc’ is
displayed. Press MENU to store the rotation setting.
Auto-Off/Sleep Mode
Press the MENU button until ‘SLEEP’ is shown at the top of the display. Press the
SET button to step through the sleep interval settings from ‘10’ seconds to ‘180’
seconds in 10-second intervals, or to turn the sleep function ‘off.’ Press MENU to
store the sleep interval and the unit will enter sleep mode at the specified number
of seconds without movement detected. END will flash momentarily to show that
all settings are saved.
Note: When the probe is open and the unit is in sleep mode, any motion detected
by the Thermapen will conveniently wake the instrument and turn it back on.
When you are done adjusting settings, replace the battery cover and tighten the
battery cover screw with a Philips screwdriver. Do not overtighten.
Calibration
Each Thermapen is individually factory-calibrated using very high-precision temperature
standards that are traceable to NIST (national standards). A certificate with actual test data is
supplied with your Thermapen. However, if you have any doubt about its accuracy, you can
check it yourself in a properly prepared ice bath. If it reads correctly in the ice bath, it is almost
certainly accurate at other temperatures.
Making a Proper Ice Bath
Fill a cup or glass with ice. Add just enough water to fill the gaps between the ice. (If the ice
is floating, the water beneath the ice will be at a higher temperature.) After a few moments,
immerse the tip of the Thermapen probe to the middle of the ice and gently stir. Within 3
or 4 seconds the Thermapen will read 32°F within 1°F. Do not let the tip of the probe rest
against an ice cube or it will read a lower temperature (it’s that fast and sensitive). If the
reading is within the published specification, the Thermapen is accurate. You can also test
MENU
SET

Produkt Specifikationer

Mærke: ETI
Kategori: Madtermometer
Model: Thermapen Mk4

Har du brug for hjælp?

Hvis du har brug for hjælp til ETI Thermapen Mk4 stil et spørgsmål nedenfor, og andre brugere vil svare dig


Madtermometer ETI Manualer

ETI

ETI Thermapen Mk4 Manual

30 August 2024

Madtermometer Manualer

Nyeste Madtermometer Manualer

Testo

Testo 270 BT Manual

3 Januar 2025
FCC BBQ

FCC BBQ FCC-A-10031 Manual

28 December 2024
La Crosse Technology

La Crosse Technology 314-1410 Manual

26 December 2024
TFA

TFA Hyper BBQ 14.1513.01 Manual

7 December 2024
TFA

TFA 14.1510 Manual

7 December 2024
Velleman

Velleman DTP10 Manual

4 December 2024
Patton

Patton Emax Bluetooth Smart thermometer I Manual

6 Oktober 2024
Hendi

Hendi 271315 Manual

21 September 2024
Laserliner

Laserliner ThermoSpot Manual

14 September 2024
Taylor

Taylor 9840 Manual

9 September 2024