Exalux Connect TX100N Manual

Exalux Ikke kategoriseret Connect TX100N

Læs gratis den danske manual til Exalux Connect TX100N (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 46 personer og har en gennemsnitlig bedømmelse på 4.6 stjerner ud af 23.5 anmeldelser. Har du et spørgsmål om Exalux Connect TX100N, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/2
1 - GENERAL INFORMATION
This instruction manual contains important notifications regarding the
safe use of the EXALUX™ CONNECT TX100N.
Please take the time to read this manual carefully and thoroughly
before installing and operating the devices. We recommend you to
keep a copy for future use and transfer it to the buyer if you resell the
device.
EXALUX™ reserves the right to modify and upgrade its range of
products, with no obligation to integrate these changes into products
already sold. Therefore, all the information found in this manual is
subject to change without notice.
2 - TECHNICAL SPECIFICATIONS
3 - OPERATING CONDITIONS
4 - RADIO INTERFACE
5 - WARRANTY
EXALUX™ cannot be responsible for material or personal damage
resulting from improper use of the product or non-compliance to the
instructions. The warranty will not be applied in these cases.
6 - OVERVIEW
The CONNECT TX100N is a wireless DMX emitter that uses LumenRadio
CRMX technology (2.4GHz). This system allows the users to connect to
DMX enabled fixtures wirelessly, several tens meters away from CRMX
receivers. CONNECT TX100N can transmit an entire DMX universe (512
channels).
Power supply input
Power consumption
DMX interface
Supported protocols
Display
Control
Housing
Protection
Certifications
Weight
Dimensions
DCJack 2.1 x 5.5mm
XLR5 Male - « Power Over DMX »
1.5W max
XLR5 Male (Neutrik®)
DMX512-A ANSI E1.11
3 LED indicators
1 push button on membrane switch
Aluminum, steel, plastic
IP30
CE
185g (with M10 bracket & antenna)
26 x 43 x 112mm
(with M10 bracket, without antenna)
Input voltage
(DCJack)
Storage temperature
Operating temperature
+ 4.75Vdc
- 10°C
+ 28Vdc
Minimum Maximum
+ 55°C
- 20°C + 75°C
Input voltage
(XLR5 - « Power Over DMX »)
+ 4.75Vdc +5.25Vdc
Standard / technology
Frequency range
CRMX by LumenRadio™
2.402 ~ 2.480 GHz
2dBi - 50ohms - SMA - removable
omnidirectional - 360° hinged
20dBm /100mW
(ETSI compliant)
GFSK Cognitive coexistence
(dynamically avoids occupied frequencies)
500 – 1000m
(open field line of sight - depending on the
receiver and the environnement)
Antenna
RF output
RF modulation
Range
7 - CONTROL
8 - POWER SUPPLY
The TX100N can be powered by two different ways :
- from DCJack connector [4.75 - 28Vdc]
- from XLR5 connector [4.75 - 5.25Vdc]
Powering the system out of this range can cause malfunctions and the
destruction of the product.
When powered, the red power indicator turns on.
Powering from DCJack connector
Always check the compatibility of the DCJack connector before powering
the emitter. EXALUX
™
recommends using the USB-DCJack or DTAP-DCJack
cords provided with the device.
The CONNECT TX100N is delivered with an adhesive cable mount and zip
ties. You can lock the cable with zip tie to avoid unintentional cord
disconnection.
Powering from XLR5 connector
The TX100N embeds the PoD technology (Power Over DMX) which enables
to power the device from its XLR5 connector (+5Vdc on pin N°5). The DMX
signal and the PoD power supply have a common ground (Ground on pin
N°1). Always check the compatibility between devices before powering.
When using a DMX cable, check that the 5 pins of the XLR connectors are
electrically connected (on most DMX cables, only pins 1, 2 and 3 are
connected). Do not exceed a length of 2 meters.
9 - DMX INPUT
The CONNECT TX100N is designed for DMX equipments. It does not
support RDM protocol. The CRMX radio signal emitted by the TX100N
transmits the DMX signal sent to the XLR5 connector (1:GND / 2:DMX- /
3:DMX+).
The blue indicator DMX turns on when a valid DMX signal is received on
the XLR5.
1
2
3
4
5
1: Ground
2: DMX-
3: DMX+ 4: Detect (PoD)
5: +5Vdc (PoD)
Cable locking
using zip tie
(max tie width: 4.1mm)
Positive polarity
«STATUS» indicator (Blue)
- ON : Active radio, DMX data present
- Slow flashing (ON 100ms / OFF 900ms) :
Active radio, no DMX
- Fast flashing (ON 100ms / OFF 100ms) :
Linking with receiver(s)
- Medium flashing (ON 200ms / OFF 200ms) :
Unlinking receiver(s)
«DMX» indicator (Blue)
- ON : valid DMX stream on XLR5
- OFF : no DMX
«POWER» indicator (Red)
- ON : device is powered
- OFF : device is off
«LINK/UNLINK» pushbutton
- Short press (<1 second) : Link
- Hold (>3 seconds) : Unlink
10 - LINKING WITH RECEIVER(S)
To link the TX100N with receiver(s), follow this procedure :
- Make sure all devices to be paired are powered.
- Start the linking procedure by pressing the «LINK/UNLINK» pushbutton on
the emitter.
- During the linking period (~10s), the DMX signal is not transmitted. Any
unlinked receivers in range will automatically link to the emitter. Several
receivers can be linked to the same emitter during a single procedure.
- When the TX100N is linked to one or more receivers, the blue «STATUS»
indicator turns on.
11 - UNLINKING RECEIVER(S)
At any time, it is possible to unlink all receivers from the emitter. To do so,
press the «LINK/UNLINK» pushbutton during 3 seconds, until the «STATUS»
indicator blinks at 2,5Hz.
12 - RADIO
The antenna is manually adjustable (X: +90° / Y: 360°). Take care not to
exceed over this angle.
The antenna of the TX100N is removable. The antenna connector on
device is an SMA-female Jack, equipped with a 50 ohms coaxial cable.
Always check the compatibility of the antenna with the device. EXALUX™
recommends the use of the antenna provided with the unit.
To maximise the radio efficiency, it is recommended to install the device in
an open space, without any structure or metal objects. It is also
recommended to orient the antennas as shown in the illustration below:
13 - SAFETY INSTRUCTIONS
Proper use:
This unit is designed to control any DMX equipment. Use the device only in its
intended use as described in this manual. The device should only be used by people
in full possession of their physical, sensory and mental abilities who must have the
knowledge and experience required. All the other persons are only allowed to use
the device under the supervision or direction of a person responsible for their safety.
Safety:
Risk of electric shock
This system requires voltage, which can result in an electrical shock. Never remove
covers. The parts inside the device are maintenance free.
Dangers for children
Ensure a proper disposal of plastic envelopes and packaging. They should not be
near babies nor young children: suffocation danger. Make sure that children do not
remove and swallow small parts of the unit (e.g. knobs, screws or similar). Never leave
unattended children use electrical devices.
Electric shock caused by a short circuit
Do not modify the power cord nor the plug. In case of noncompliance, there is a risk
of electric shock and fire hazard. If in doubt, contact a certified technician.
Risk of fire
Never cover the device. Do not install the device close to a source of heat. Keep the
device away from flames.
Terms of use
The device is designed for indoor use. To prevent damage, do not expose the
product to liquid or moisture. Avoid direct sunlight, clogging and strong vibrations.
CARE
- Unplug the unit when cleaning it and during all maintenance operations
- Do not remove the serial number sticker.
- Do not use cleaning product: use a dry cloth and rub gently.
- Store the device in a clean, dry place, away from direct exposure from
sunlight and dust.
TX TX
RX
RX
Y: 360°
X: 90°
CONNECT TX100N
2.4GHz CRMX EMITTER
EXALUX is a registered trademark of
the French Tech company LEDIXIS
1 rue de la Noë - Bat. IM3
CS 12111 44322 Nantes cedex 3
FRANCE
+33 (0)9.72.45.70.43
www.exalux.eu
Information:
contact@exalux.eu
Technical support:
support@exalux.eu
Last updated on 10-2020

Produkt Specifikationer

Mærke: Exalux
Kategori: Ikke kategoriseret
Model: Connect TX100N

Har du brug for hjælp?

Hvis du har brug for hjælp til Exalux Connect TX100N stil et spørgsmål nedenfor, og andre brugere vil svare dig


Ikke kategoriseret Exalux Manualer

Exalux

Exalux Connect TX100N Manual

20 August 2024
Exalux

Exalux Connect RX200N Manual

20 August 2024
Exalux

Exalux Connect RX100S Manual

19 August 2024
Exalux

Exalux Connect One Manual

19 August 2024
Exalux

Exalux Control One Manual

18 August 2024
Exalux

Exalux Control Touch Manual

17 August 2024
Exalux

Exalux Control Sky Manual

17 August 2024
Exalux

Exalux Connect+ Manual

22 Juli 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Siemens

Siemens WQ32G28IL Manual

6 December 2025
MDT

MDT BE-TA550606.02 Manual

6 December 2025
Opticis

Opticis USC-CC32 Manual

6 December 2025
Audio-Technica

Audio-Technica AT33xMONO Manual

6 December 2025
Bosch

Bosch SPI4EMS24E Manual

6 December 2025
Fostex

Fostex P1000K Manual

6 December 2025
Advantech

Advantech UTC-124I1 Manual

6 December 2025
Anton/Bauer

Anton/Bauer Titon Micro Kit Manual

6 December 2025
Philips

Philips Zoom! DayWhite DIS130 Manual

6 December 2025
Opticis

Opticis USB-FC30AA Manual

6 December 2025