Extron DTP R HWP 4K 331 D Manual

Extron Modtager DTP R HWP 4K 331 D

Læs gratis den danske manual til Extron DTP R HWP 4K 331 D (4 sider) i kategorien Modtager. Denne vejledning er vurderet som hjælpsom af 15 personer og har en gennemsnitlig bedømmelse på 4.6 stjerner ud af 8 anmeldelser. Har du et spørgsmål om Extron DTP R HWP 4K 331 D, eller vil du spørge andre brugere om produktet?

Side 1/4
IMPORTANT:
Go to www.extron.com for the complete
user guide, installation instructions, and
specifications before connecting the
product to the power source.
1
DTP R HWP 4K D Series • Setup Guide
This setup guide provides instructions for an experienced installer to set up and operate the Extron DTP R HWP 4K 231 D and
DTP R HWP 4K 331 D extenders.
Installation
Step 1 — Disconnect Power
Disconnect all equipment power sources.
Step 2 — Prepare the Mounting Surface
ATTENTION:
Installation and service must be performed by authorized personnel.
Linstallation et l’entretien doivent être effectués par le personnel autorisé uniquement.
The unit must be installed in accordance with the National Electrical Code and with local electrical and safety
codes.
Lunité doit être installée conformément au National Electric Code et aux normes électriques et de sécurité locales.
NOTE: Use the included mud ring (MR 200) or a UL approved 1-gang RACO wall box (not supplied) with a depth of at
least 3.0 inches (7.6 cm). For more information, see the full product user guide at www.extron.com.
a. Place either the mud ring (see gure on page 1) or the wall box (see gure on page 2) against the installation surface and
mark the opening guidelines.
TIP: Use a level to mark the opening.
b. Cut out the material from the marked area.
c. Either:
Insert the mud ring into the opening, rotate the locking
arms, and secure it with the supplied screws,
or
Secure the wall box to the wall stud with 10-penny nails
or #8 or #10 screws, leaving the front edge ush with the
surface.
TLP T1000
V
IN1608
100-240V ~ -- A MAX
1
2
CONFIGURABLE
HDMI HDMI
5
6
7 8
C
RS-232 IR
RS-232 IR
TxRx Tx RxG
TxRx Tx RxG TxRx T x RxG
HDMI
A
B
3
4
INPUTS OUTPUT S
Tx Rx
RS-2 32
G
LAN
2x25W(8Ω)/2x50W(4Ω)
RESET
AUDIO INPUT S OUTPUT S
REMOT E
L L1 R R
L 2 R
L
3
R
CLASS 2 WIRING
L 4 R
L 5 R
+48V
+48V
1 2
L R
VARIABLE
IN1608 S A
2
MIC/LINE
L 6 R
SIG LINK
DT N
SIG LINK
D IN
SIG LINK
DTP UT
50/60 Hz
RS-232 IR
OVER DTP
OVER DTP
OVER DTP
AMPLIFIED OUT PUT
VOLUME
SCALING PRESENTATION SWITCHER
IN 16 08
INPUTS
1
HDCP
SIGNAL
OUTPUTS
ENTER
MENU
Ext r on
2 3 4 5 6 7 8 A B C
IN PUTS
12345678
CONFIG
Extron
DTP T UWP 2 D23
Transmitter
Extron
DTP T HWP 2 D23
Transmitter
Extron
DTP R P HW 4K 331 D
Receiver
Ethe etrn
XTP eDTP 24 Cabl
230'
AUTO SW
CONFIG
IR OUT
HDMI IN
AUDIO IN
S
G
HDCP
1
AUDIO IN
VGA IN
AUTO S W
CONFIG
IR OUT
HDMI IN
AUDIO IN
S
G
HDCP
1
HDMI IN
AUDIO IN
HDCP
1
2
HDMI OUT
GT x Rx
Tx Rx
OVER DTP
RS-232 IR
Projector
HDMI
I O 0PCP PR 55
21
LIMIT
RIR
Tx
Rx
Tx
Rx
RTS
CTS
COM
IR/SERIAL RELAYS FLEX
I/O
S LIMIT
eBUSSWITCHED
12 VDC
1000
LINK
ACT
IPCP PRO 550
OVER
43 1 2 3 4 5 6 7 8
OVER
5678
21
3 4
213 4
5678
21 3 4
Rotate locking arm
and insert into llwa
opening.
Mud Ring
2
DTP R HWP D 4K Series • Setup Guide (Continued)
d. Run all required cables (see steps , , and ),3 4 5
thread the cables through the mud ring or walll
box, and secure them with cable clamps.
TIP: In order to t the unit in the junction
box, do not install boots on TP cables
and RJ-45 connectors.
Step 3 — Run Cables Between Units
Connect the rear panel transmitter output to a rear panel receiver input using twisted pair cable.
Wire the cable as shown in the diagram to the right.
For optimal performance, Extron highly recommends the following:
RJ-45 termination with shielded twisted pair cable must comply with TIA/EIA-T568B
wiring standard for all connections. For more information on TP cable wiring and
termination, see the at DTP R HWP 4K 231 and 331 D User Guide www.extron.com.
Use shielded twisted pair cable, 24 AWG solid conductor or better, with a minimum cable
bandwidth of 400 MHz.
ATTENTION:
Do not use Extron UTP23SF-4 Enhanced Skew-Free AV UTP cable to link the device with DTP transmitters or
receivers.
N’utilisez pas le câble AV Skew-FreeUTP version améliorée UTP23SF d’Extron ou le câble STP201 pour relier
le appareil avec les émetteurs ou les récepteurs DTP.
NOTE: Extron XTP DTP 24 Shielded twisted pair cable is strongly recommended for
optimal performance.
Use shielded RJ-45 plugs to terminate the cable.
Limit the use of RJ-45 patches. Overall transmission distance capabilities vary
depending on the number of patches used. If possible, limit the number of patches to
two total.
If RJ-45 patches must be used in the system, shielded patches are recommended.
Step 4 — Connect Output Device
Front Panel
A DTP RS-232 and IR connectors — To pass serial or infrared data or control signals,
such as serial control of a projector, connect the host device to the transmitter and the
peripheral device to the receiver via the RS-232 and IR captive screw connectors on
both units.
B HDMI output connector Connect an HDMI cable between this port and the input on
a sink device.
HDMI OUT
Extron
OVER DTP
A
B
DTP R HWP 4K 231 D
and DTP R HWP 4K 331 D
Front Panel
5
Pin
1
2
3
6
7
8
4
Wire color
White-green
Green
White-orange
White-blue
Orange
White-brown
Brown
Blue
TIA/EIA
T568-B
TP Wires
1 8234567
Pins:
Wall Stud
Screws
or Nails
Signal
Output
Cabl
e
Decorator-Style Faceplate
Extron
DTP R HWP 4K 231 D
HDMI OUT
Ext ron
OVER D TP


Produkt Specifikationer

Mærke: Extron
Kategori: Modtager
Model: DTP R HWP 4K 331 D

Har du brug for hjælp?

Hvis du har brug for hjælp til Extron DTP R HWP 4K 331 D stil et spørgsmål nedenfor, og andre brugere vil svare dig