Extron MTP T 15HD A Manual

Extron AV forlænger MTP T 15HD A

Læs gratis den danske manual til Extron MTP T 15HD A (2 sider) i kategorien AV forlænger. Denne vejledning er vurderet som hjælpsom af 10 personer og har en gennemsnitlig bedømmelse på 4.7 stjerner ud af 5.5 anmeldelser. Har du et spørgsmål om Extron MTP T 15HD A, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Product Category

IMPORTANT:

Go to www.extron.com for the

complete user guide and installation

instructions before connecting the

product to the power source.

Power Supply

Output Cord

SECTION A–A

Ridges

Smooth

Tie

Wrap

POWER

12V

0.5A MAX

Rear

Panel

Ridges

Earth

Ground

3/16"

(5 mm)

Max.

MTP 15HD A Series • Setup Guide

This guide provides instructions for an installer to set up and operate

any of the Extron MTP 15HD A transmitters and receivers.

Installation

1. Turn off all MTPs and devices.

Turn the input and output devices off and unplug their power

cords. Verify that all MTPs are disconnected from the power

sources before proceeding.

2. Connect the transmitter inputs.

• Connect a VGA video source to the Input connector (

)

• Connect a VGA monitor to the Monitor connector (

)

• Connect a 3.5 mm stereo audio plug into the Audio connector (

Wire the plug as shown in gure 2.

3. Terminate and connect TP cables between units.

• Connect a TP cable between the Output connector (

) of the transmitter and the Input

connector (

) of the receiver. Terminate the cable ends identically with either standard as

shown in gure 3.

• For daisy-chaining, connect up to eight receivers using TP cables between the Buffered

Output connector (

) of a receiver and the Input connector (

) of a daisy-chained receiver.

4. Connect the receiver outputs.

• Connect a VGA display to the Output connector (

)

• Connect a 3.5 mm, 5-pole captive screw audio connector into the Mono Audio

connector (

) for two mono audio outputs. Wire the connector as shown in gure 4.

ATTENTION: Connect the sleeves to the ground (G). Connecting the sleeves

to a negative (–) terminal will damage the audio output circuits.

5. Configure the receiver DIP switches.

See figure 5 for DIP switch (located on the front panel of the receiver) layout and settings.

• H Sync + and V Sync + switches — Set these switches On (up) for positive sync or Off

(down) for negative sync.

• S-Video switch — Set this switch ON (up) to output chroma on pin 3 and luma on pin 2.

Set this switch OFF (down) to output chroma on pin 1 and luma on pin 2.

• End Unit switch — Set this switch On (up) if either of the following is true:

• The receiver being congured is the only receiver connected

to the transmitter.

• The receiver being congured is the last receiver in a daisy-chained system.

Set the End Unit switch Off (down) on the receiver being congured if there are one or

more receivers connected to the Buffered Output RJ-45 connector.

6. Terminate the power cable and ground the unit.

ATTENTION: See “Power Supply Wiring” in the user guide before wiring.

Wire the 2-pole captive screw connectors as shown in gure 6. Plug them into the Power connectors (

)

of the MTPs. The LED indicator on each MTP should be on when receiving power.

Grounding guidelines:

Extron MTP 15HD A products can be adversely affected by electrostatic discharge

(ESD)

if they are not

grounded

corr

ectly

To prevent malfunctions or product damage, an installer can correctly ground an Extron MTP 15HD A series

product by grounding the power input port. Insert one end of the grounding wire to the negative

ground pin

on the power input connector

(see

gure 6). Tie the other end of

the

wir

to an earth

ground.

If you have any questions about how to ground a product in a specic application, contact an Extron

technical

support

specialist.

Sleeve ( )

Ring

Right (

)

Tip

Left (+)

Figure 1. Transmitter and Receiver Rear Panels

Figure 2. Stereo Audio Plug

OUTPUT

INPUT

AUDIO

POWER

12V

.5A MAX

MONITOR

PRE-PEAK

OFF

MTP T 15HD A

INPUT

BUFFERED

OUTPUT

OUTPUTS

RGB

POWER

12V

.5A MAX

MTP RL 15HD A

MONO AUDIO

651 32

7 8 9

12345678

Insert Twisted

Pair Wires

Pins:

NOTE: If you are using Enhanced Skew-Free™

A/V cable, use the TIA/EIA T568A standard only.

T568A

Wire Color

White-green

Green

White-orange

Blue

White-blue

Orange

White-brown

Brown

T568B

Wire Color

White-orange

Orange

White-green

Blue

White-blue

Green

White-brown

Brown

Figure 3. TP Termination

MONO AUDIO

Unbalanced Output

Balanced Output

Do not tin the wires!

Tip

Ring

Tip

Ring

Sleeves

Tip

No Ground Here

Tip

Sleeves

Figure 4. Captive Screw

Connector

1 2 3 4 5

H SYNC +

V SYNC +

S-VIDEO

END UNIT

SPARE

Figure 5. DIP Switches

Figure 6. Power Wiring

and Grounding

Produkt Specifikationer

Mærke:	Extron
Kategori:	AV forlænger
Model:	MTP T 15HD A
Type:	AV sender
Vekselstrømsindgangsspænding:	100-240 V
Vekselstrømsindgangsfrekvens:	50 - 60 Hz
Produktfarve:	Black, Grey
Pakkevægt:	830 g
Opbevaringstemperatur (T-T):	-40 - 70 °C
Relativ luftfugtighed ved drift (H-H):	10 - 90 %
Relativ luftfugtighed ved opbevaring (H-H):	10 - 90 %
Driftstemperatur (T-T):	0 - 50 °C
Maksimal opløsning:	2048 x 1080 pixel
Impedens:	75 ohm (Ω)
Certificering:	CE, c-UL, UL\nC-tick, FCC Class A, ICES, VCCI
Pakkens dimensioner (BxDxH):	186 x 265 x 73 mm
RJ-45 indgangs-porte:	1
Stativ-montering:	Ja
VGA (D-Sub) indgangsporte:	2
Understøttede kabeltyper:	Cat5, Cat5e, Cat6
Senderdimensioner (BxDxH):	109 x 76 x 43 mm
Transmitter vægt:	500 g