Extron NetPA U 8001 SUB Manual

Extron Modtager NetPA U 8001 SUB

Læs nedenfor 📖 manual på dansk for Extron NetPA U 8001 SUB (34 sider) i kategorien Modtager. Denne guide var nyttig for 37 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF
Side 1/34
User Guide
NetPA U 8001 SUB
NetPA Ultra Series
Mono Subwoofer Amplifier with Dante and DSP
68-3414-01 Rev. A
10 22
NetPA U 8001 SUB • Installation 11
LIMITTER / PROT
ECT
S IGNAL
R
OVERTEMP
1 2 1 2
RS-232
S TANDBY
Tx Rx G G
AT CONFIG LINE OUTLINE INREMOTE
CLAS S 2 WIRING
TS
240V--1.7A, 50-60 Hz
etPA U 8001 SUB
MITER/PROTECT
SIGNAL
8Ω/4Ω OUTPUT
CLASS 2 WIRING
NetPA U 8001 SUB
Figure 11. Connecting the Amplifier to the Subwoofer
NetPA U 8001 SUB • Installation 14
3. Remove the two screws holding the blue hot (line) and the brown neutral wires from the
terminal block on the PCB. Put the screws to the side to be used later (see figure 13
on page 13).
4. Remove the ground wire nut from the grounding stud located on the bottom of the
enclosure, as shown below. Place the wire nut with the other screws to be used later.
5. Remove the wires attached to the IEC connector from the body of the amplifier, and
slide the IEC connector and attached wires up and out of the amplifier enclosure.
6. Remove the washer at the end of the conduit (see Washer-B in figure 14), and remove
the conduit adapter plate that ships attached to the conduit.
Separate adapter plate
and washer from conduit
Washer-B
Washer-A
Conduit Adapter Plate
Figure 14. Removing the Existing Adapter Plate
7. Place the adapter plate that ships with the conduit kit on the conduit, with the flat side
of the plate facing the hexagonal nut (washer-A), and secure the new plate to conduit
with the washer that was removed back in step 6, washer-B (see figure 15).
Place the adapter plate
with the flat side against
washer-A and secure with
washer-B.
Washer-B
Washer-A
NetPA Ultra Series Conduit
Adapter Plate
Figure 15. Secure NetPA Ultra Series Adapter Plate to Conduit
8. Thread the blue, brown, and green 18-gauge power wires that are included with the
flexible conduit adapter kit through the length of the electrical conduit.
9. Install the conduit with the new conduit plate attached into the opening from where the
IEC connector was removed in step 5 (see figure 16 on page 15).
NetPA U 8001 SUB • Operation 16
Operation
This section describes the operation of the NetPA U 8001 SUB Amplifiers. Topics include:
• Front Panel Features Rear Panel Features Operation• •
Front Panel Features
1 Power/Standby LED 2 Over Temp LED 3 Channel Status LEDs
Figure 17. NetPA U 8001 SUB Front Panel
NOTE: The front panels of all models in the NetPA Ultra Series function identically.
1 — A single LED that lights green when the unit is on and active, Power/Standby LED
and lights amber when:
• The unit is powering up and booting.
• The unit is in standby mode, which turns off all outputs from the amplifier although
the amplifier still receives power.
• DC voltage is detected (see Troubleshooting on page 96).
This LED unit flashes amber when an “Identify Device” request is sent to the unit via
Dante Controller, and the Link Indicator LED located on the rear panel blinks green.
Once the cycle has been completed, the LED returns to normal.
NOTE: Power indicator LED may light amber for a short time after the removal
of AC power. This is normal.
2 Over Temp Indicator — A single LED that lights red when the amplifier has exceeded
the maximum recommended operating temperature. The amplifier recovers once the
unit has sufficiently cooled down (see Troubleshooting).
3 — Two rows of two LEDs on the NetPA U 8001 SUB that Channel Status LEDs
represent amplifier channels.
• Limiter/Protect LED — This LED lights red when the channel is in protection
mode, which is triggered by any of the limiter protection circuits such as:
• When the channel is in an overload situation.
• When the output short circuits.
• When digital clipping is detected on the output of the DSP going into the
amplifier channel.
• When the channel overheats.

Produkt Specifikationer

Mærke: Extron
Kategori: Modtager
Model: NetPA U 8001 SUB

Har du brug for hjælp?

Hvis du har brug for hjælp til Extron NetPA U 8001 SUB stil et spørgsmål nedenfor, og andre brugere vil svare dig


Modtager Extron Manualer

Extron

Extron XTP R HWP 201 4K Manual

30 September 2024
Extron

Extron DP DA2 Manual

24 September 2024
Extron

Extron DA HD 8K L Manual

11 September 2024
Extron

Extron DVI DA Plus Series Manual

11 September 2024
Extron

Extron DA HD 4K Manual

11 September 2024
Extron

Extron XPA U 2002 SB Manual

7 September 2024
Extron

Extron XPA U 3502 Manual

7 September 2024
Extron

Extron DTP2 R 211 Manual

7 September 2024
Extron

Extron XTP SFR HD 4K Manual

6 September 2024
Extron

Extron XPA U 1002 Manual

6 September 2024

Modtager Manualer

Nyeste Modtager Manualer

Meliconi

Meliconi AT 380 USB Manual

8 April 2025
AudioSource

AudioSource ADTV3.1 Manual

8 April 2025
LEA

LEA CS702-G Manual

8 April 2025
ESX

ESX Quantum QS-FOUR Manual

7 April 2025
DJI

DJI D-RTK 3 Manual

4 April 2025
Phonocar

Phonocar PH5130 Manual

4 April 2025
Phonocar

Phonocar PH544 Manual

4 April 2025
Phonocar

Phonocar PH545 Manual

4 April 2025
Phonocar

Phonocar PH560 Manual

4 April 2025
Phonocar

Phonocar PH564 Manual

4 April 2025