Fisher 29841 Manual

Fisher Ikke kategoriseret 29841

Læs gratis den danske manual til Fisher 29841 (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 19 personer og har en gennemsnitlig bedømmelse på 4.9 stjerner ud af 10 anmeldelser. Har du et spørgsmål om Fisher 29841, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

1. Do not use reel at higher pressures or temperatures than listed on

the back of these instructions.

2. Remove all spring tension before beginning dissassembly process.

SAFETY

INSTALLATION:

LUBRICATION:

REPLACING HOSE:

ADJUSTMENTS:

REPAIRS:

MOUNTING:

Dimensions

A 11 3/16”

B 11 1/16”

C 6”

D 8”

E 4 3/16”

F 6”

G 2 1/2”

Operating Instructions

Model: 29841 / 29662

Spring Driven Reel

Fisher Manufacturing Co. • 1900 “O” Street, Tulare, CA 93274

Ph: 800-421-6162 / 559-685-5200 • Fax: 800-832-8238 / 599-685-5222

Part No.75031 Rev.A

A flexible hose connection must be used between the hose reel inlet and the source of supply to prevent possible

misalignment and binding. Turn over the page for more detailed instructions and drawing configuration.

This reel is configured to be under the counter mounted.The hose reel is equipped with a universal mounting bracket so that it can

be mounted on the floor, wall or hose guide arm accessory kit (sold separately)or ceiling. In order to modify it”s factory set position the

can be moved to the position desired by removing two screws fastening the spring case to the reel base. Shift the guide arm bracket

so the hose comes off the reel at the desired position and replace the screws. CAUTION: Unless reel was specified differently when

ordering. maximum height is 16 feet.

Hose reel spring and bearings are factory lubricated and require no further lubrication.

1. Wind spool flange clockwise-facing swivel-until spring is tight

2. Back off three turns and latch.

3. Insert hose through roller guide.

4. Connect hose fitting to swivel joint and secure hose with clamps.

To adjust spring tension, add or remove wraps of hose from the spool, one wrap at a time until desired tension is

obtained.

Extensive repairs should be performed only by an authorized serviceman or factory to avoid damage which may

void your warranty. Remove all spring tension before beginning disassembly process.

Model: 29841 / 29662

Model: 74989 Reel Kit Utilty Spray Valve / Pro Spray

Page 2

Description

29841 or 29662

Hose I.D. and Length 3/8” x 20’

Reel Inlet Connection 3/8” NPT (F)

Hose Outlet Connection 1/4” NPT(M)

Max. Operating Pressure 300 PSI

Max. Operating Temperature 160 °F

Item # Description # Req.

1 Swivel and elbow assy, 3/8 LP, 3/8 MPT x FPT 1

2 Hardware Kit 1

Spacing washer 1.005 ID x 1.312 OD x .020 THK 2

Snap ring 1

Hex washer screw 3

Hex lock nut M5 8

Machine screw M5 x 10 8

Screw set 3/8-16 x 1/2 1

Nyloc nut M6 2

U-bolt 1

3 Main shaft with snap ring 1

4 Sheave Assembly 1

Sheave flange 1

Sheave disc 1

Ratchet arbor 1

Item # Description # Req.

5 Base and roller assembly 1

Tube rivet 4

Universal roller (2”) 1

Base weldment assembly 1

6 Drive spring assembly 1

7 Spring case stud 1

8 Spring case assembly 1

9 Bumper assembly

10 Latch pawl assembly 1

Latch pin 1

Latch pawl 1

Torsion spring 1

11 Hose assemby

12 Guide arm assembly w/ hardware

(sold separately) 1

Item # Req.# Part Description

13 175066 Hose RR 3/8m x 1/2f x 1 1/2 ft

14 12900-3309 Bushing 1/4f x 3/8m brs

12980-R020 Tube vinyl clear 6 inch15

16 12913-3/8 Handle 3/4-14f X 3/8f

17 12922-5000 Gasket Handle

18 12920 or 2990 Utility Spray Valve or Pro Spray

19 13298 PST Thread Sealant

1. Connect the lead-in line (13) to the reel (29841 / 29662) inlet located on the right-hand side of the hose reel,

by appling PST (19) or plumbers tape on the male 3/8” NPT threads on the lead-in line (13) and thead it

to the reel (29841) using a wrench to support the swivel while tightening the lead-in line.

2. Connect the 1/2” female end of the lead-in line (13) to the water supply using PST (19) or plumbers tape

and tighent.

3. Turn on water supply and flush the reel line to remove any debis from the reel for a few seconds and

then turn off water supply.

4. Attach the bushing (14) to the reel hose (11) By appling PST (19) or plumbers tape on the 1/4” NPT male threads on reel hose

and tighten.

5. Slide the clear vinyl tube (15) over the reel hose up to the bumper (9).

6. Attach the handle (16) to the reel hose (11). By appling PST (19) or plumbers tape on the 3/8” NPT male threads on reel hose

and tighen.

7. Insert the gasket handle (17) into the handle (16) and then connect the pro spray valve (18).

8. Turn water supply on and check for leaks.

NOTE: Apply PST or Plumber Tape on

the following locations to prevent any

leaks.

Produkt Specifikationer

Mærke:	Fisher
Kategori:	Ikke kategoriseret
Model:	29841

Har du brug for hjælp?

Hvis du har brug for hjælp til Fisher 29841 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Fisher Manualer

Fisher 29841 Manual

19 August 2024

Fisher 32027 Manual

18 August 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Tripp Lite Protect It! TLP606TAA Manual

31 Juli 2025

Holzmann MFS1SET Manual

31 Juli 2025

Tripp Lite NFI-U05A Manual

31 Juli 2025

Saris Fluid 2 Manual

31 Juli 2025

Eibenstock BST 250 Manual

31 Juli 2025

Intermatic ET2825CR Manual

31 Juli 2025

Tripp Lite Protect It! TLP808TEL Manual

31 Juli 2025

Tripp Lite SmartOnline SU5000XFMRT2U20 Manual

31 Juli 2025

Tripp Lite DRS-1215 Manual

31 Juli 2025

Tripp Lite N286-10G-SR-C Manual

31 Juli 2025