FLIR Forge Manual

FLIR Ikke kategoriseret Forge

Læs gratis den danske manual til FLIR Forge (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 41 personer og har en gennemsnitlig bedømmelse på 4.4 stjerner ud af 21 anmeldelser. Har du et spørgsmål om FLIR Forge, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

GETTING

GETTINGGETTING





STARTED

STARTEDSTARTED

FORGE®

GigE Vision

Will

WillWill your

your

youryour system

system

systemsystem support

support

supportsupport the

the

thethe camera?

camera?

camera?camera?

Recommended System Configuration:

OS—Windowsor Linux (32- or 64-bit)

CPU— Intel i7 or greater

RAM—8 GB dual channel

Ports—GigE network adapter with 5G Full Duplex support

Software—Microsoft Visual Studio 2015 (to run and compile example code)

DoDo you

you

youyou have

have

havehave a

aa downloads

downloads

downloadsdownloads account?

account?

account?account?

A downloads account is required to download software and firmware.

1. Go to .www.flir.com/account

2. Enter your email address and click Continue.

3. Complete the Create an account form and click Continue.

4. You will receive an email with a link to activate your account.

5. Once activated, you can login using the credentials you've created.

The has many links to help you operate your cameraForge resources page

effectively, including:

Spinnaker

SDKsoftware, including drivers (login required)

Firmware updates and release notes (login required)

Dimensional drawings and CADmodels

Documentation

DoDo you

you

youyou have

have

havehave all

all

allall the

the

thethe parts

parts

partsparts you

you

youyou need?

need?

need?need?

To install your camera you need the following components:

Ethernet cable

Powered Ethernet switch or Ethernet power injector (if using PoE)

GPIOcable

Lens

Tripod adapter (optional)

Interface card

Teledyne FLIR sells a number of the additional parts required for installation. To

purchase, visit the .Accessories page

Camera

CameraCamera Care

Care

CareCare

To clean the imaging surface of your camera, follow the steps outlined in Cleaning

the imaging surface of your camera.

Extended exposure to bright sunlight, rain, dusty environments, etc. may cause

problems with the electronics and optics of the system.

Avoid excessive shaking, dropping, or mishandling of the device.

Warning! Avoid electrostatic charging.

Installing

InstallingInstalling your

your

youryour Interface

Interface

InterfaceInterface Card

Card

CardCard and

and

andand Software

Software

SoftwareSoftware

1. Install your Interface Card

Ensure the card is installed per the

manufacturer's instructions.

Connect the internal IDE or SATApower

connector on the card to the computer power

supply.

Alternatively, use your PC's built- in host

controller, if equipped.

Open the Windows Device Manager. Ensure the card is properly installed. Ethernet

cards appear under . An exclamation point (!) next to the cardNetwork Adapters

indicates the driver has not yet been installed.

Configure the network adapter to use 5G Full Duplex.

a. Update the driver to the latest to access the 5GFull Duplex option.

b. In Windows go to Control Panel\Network and Internet\Network Connections,

right-click on your network adapter and select .Properties

c. Click .Configure

d. On the Advanced tab, from the Property box select and fromSpeed &Duplex

the Value drop-down select .5Gbps Full Duplex

e. Click .OK

On the Advanced tab, if not already enabled, set the Jumbo Packet to 9014 Bytes.

2. Install the Spinnaker® SDK Software

Note: For existing users who already have Spinnaker installed, we recommend

ensuring you have the latest version for optimal performance of your camera. If

you do not need to install Spinnaker, use SpinView to install and enable drivers

for your card. Forge requires Spinnaker version 3.1 or later.

a. Go to the page.Spinnaker SDK

b. Click the Download button. You are prompted to login, if not already.

c. Select your operating system. Depending on your selection there may be other

versions to select.

d. After download is complete, open the file to start the Spinnaker setup wizard.

e. Follow the steps in each setup dialog.

3. Optimize the settings of your Ethernet card

a. In , right click on the NetworkStart->All Programs-> Spinnaker SDK->SpinView

Adapter and select Adapter Configuration. The Adapter Config Utility lists your

network adapters and allows you to access the following:

Adapter IP address

Subnet mask

Default gateway

Receive buffers

Transmit buffers

Jumbo packets

RSS

Media optimization

CPU affinity

Note: See How to Optimize GigENetwork Adapter Settings for more information

on configuring for best performance.

5/19/2023

Names and marks appearing on the products herein are either registered

trademarks or trademarks of FLIR Integrated Imaging Solutions Inc. and/or its

subsidiaries.

Produkt Specifikationer

Mærke:	FLIR
Kategori:	Ikke kategoriseret
Model:	Forge

Har du brug for hjælp?

Hvis du har brug for hjælp til FLIR Forge stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret FLIR Manualer

8 September 2025

8 September 2025

7 September 2025

7 August 2025

FLIR Blackfly S Manual

5 August 2025

FLIR Forge Manual

5 August 2025

FLIR Thermal Studio Manual

5 August 2025

FLIR SkyWatch Manual

22 Juli 2025

FLIR LS-X Manual

7 Juli 2025

FLIR Horizon 9.3 Manual

11 Marts 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Trident PreAmp 80B-PRE Manual

4 November 2025

HYTE Keeb TKL Manual

4 November 2025

Sonifex HY-03DTD Manual

4 November 2025

MSI FORGE GK110 Manual

4 November 2025

Sonifex Redbox RB-DD4 Manual

4 November 2025

WesAudio ngTubeComp Manual

4 November 2025

Listen LR-4200-216 Manual

4 November 2025

Digital Watchdog SiteWatch DW-SWSP15A Manual

4 November 2025

Wooden Camera 162600 Manual

4 November 2025

DS18 VOC10LD-PK Manual

4 November 2025