FLIR Blackfly S Manual

FLIR Ikke kategoriseret Blackfly S

Læs gratis den danske manual til FLIR Blackfly S (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 28 personer og har en gennemsnitlig bedømmelse på 4.3 stjerner ud af 14.5 anmeldelser. Har du et spørgsmål om FLIR Blackfly S, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

GETTING

GETTINGGETTING





STARTED

STARTEDSTARTED

BLACKFLY®S

Board-level GigE Vision

Will

WillWill your

your

youryour system

system

systemsystem support

support

supportsupport the

the

thethe camera?

camera?

camera?camera?

Recommended System Configuration:

OS—Windowsor Linux (32- or 64-bit)

CPU— Intel i5 or greater

RAM—4GB

Ports—GigE network adapter

Software—Microsoft Visual Studio 2010, Visual Studio 2013, or Visual Studio

2015 (to run and compile example code)

DoDo you

you

youyou have

have

havehave a

aa downloads

downloads

downloadsdownloads account?

account?

account?account?

A downloads account is required to download software and firmware.

1. Go to .www.flir.com/account

2. Enter your email address and click Continue.

3. Complete the Create an account form and click Continue.

4. You will receive an email with a link to activate your account.

5. Once activated, you can login using the credentials you've created.

The has many resources to help you operateBlackfly S Board-level resources page

your camera effectively, including:

Spinnaker

SDKsoftware, including drivers (login required)

Firmware updates and release notes (login required)

Dimensional drawings and CADmodels

Documentation

DoDo you

you

youyou have

have

havehave all

all

allall the

the

thethe parts

parts

partsparts you

you

youyou need?

need?

need?need?

To install your camera you need the following components:

Ethernet cable

Powered Ethernet switch or Ethernet power injector (if using PoE)

TF38 to FPC RJ45 PoE panel mount adapter

Heatsink (recommended)

FPC cable

GPIOcable

Lens mount and lens

Tripod adapter (optional)

Interface card

Teledyne FLIR sells a number of the additional parts required for installation. To

purchase, visit the .Accessories page

Camera

CameraCamera Care

Care

CareCare

To clean the imaging surface of your camera, follow the steps outlined in Cleaning

the imaging surface of your camera.

Extended exposure to bright sunlight, rain, dusty environments, etc. may cause

problems with the electronics and optics of the system.

Avoid excessive shaking, dropping, or mishandling of the device.

Warning! Avoid electrostatic charging.

Installing

InstallingInstalling Your

Your

YourYour Interface

Interface

InterfaceInterface Card

Card

CardCard and

and

andand Software

Software

SoftwareSoftware

1. Install your Interface Card

Ensure the card is installed per the

manufacturer's instructions.

Connect the internal IDE or SATApower

connector on the card to the computer power

supply.

Alternatively, use your PC's built- in host

controller, if equipped.

Open the Windows Device Manager. Ensure the card is properly installed. Ethernet

cards appear under . An exclamation point (!) next to the cardNetwork Adapters

indicates the driver has not yet been installed.

2. Install the Spinnaker® Software

Note: For existing users who already have Spinnaker installed, we recommend

ensuring you have the latest version for optimal performance of your camera. If

you do not need to install Spinnaker, use SpinView to install and enable drivers

for your card.

a. Go to the page.Spinnaker SDK

b. Click the Download button. You are prompted to login, if not already.

c. Select your operating system. Depending on your selection there may be other

versions to select.

d. After download is complete, open the file to start the Spinnaker setup wizard.

e. Follow the steps in each setup dialog.

3. Enable jumbo frames on the Ethernet card

a. In , right click on the NetworkStart->All Programs-> Spinnaker SDK->SpinView

Adapter and select Adapter Configuration, then select IP Configuration.

b. Click Open Network Connections.

c. Click Change Settings.

d. Click on the Advanced tab and from the Settings list select Jumbo Packet.

e. Set the Value to 9014 Bytes and click OK.

See for more information onHow to Optimize GigENetwork Adapter Settings

configuring for best performance.

Using

UsingUsing the

the

thethe Spinnaker

Spinnaker

SpinnakerSpinnaker

®®

SDK

SDKSDK

You can monitor or control features of the camera through Spinnaker API examples

provided in the Spinnaker SDK, or through the SpinView camera evaluation

application. A is included in the installation.Programmer's Guide and API Reference

11/21/2022

Names and marks appearing on the products herein are either registered

trademarks or trademarks of FLIR Systems, Inc. and/or its subsidiaries.

Produkt Specifikationer

Mærke:	FLIR
Kategori:	Ikke kategoriseret
Model:	Blackfly S

Har du brug for hjælp?

Hvis du har brug for hjælp til FLIR Blackfly S stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret FLIR Manualer

8 September 2025

8 September 2025

7 September 2025

7 August 2025

FLIR Blackfly S Manual

5 August 2025

FLIR Forge Manual

5 August 2025

FLIR Thermal Studio Manual

5 August 2025

FLIR SkyWatch Manual

22 Juli 2025

FLIR LS-X Manual

7 Juli 2025

FLIR Horizon 9.3 Manual

11 Marts 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

PAG Mini link 6002 Manual

4 November 2025

Wamsler K128 Manual

4 November 2025

Sonifex Redbox RB-DSD8 Manual

4 November 2025

Zotac ZBOX MI561 nano Manual

4 November 2025

MuxLab 500800-RX Manual

4 November 2025

Hawke Laser/LED Foregrip Manual

4 November 2025

Wooden Camera 213900 Manual

4 November 2025

Chauvet Freedom Flex Stick Battery Manual

4 November 2025

DS18 VOC8LD-PK Manual

4 November 2025

Sony XDCAM PXW-Z90 Manual

4 November 2025