Focal FDP 4.600 V2 Manual

Focal Modtager FDP 4.600 V2

Læs gratis den danske manual til Focal FDP 4.600 V2 (8 sider) i kategorien Modtager. Denne vejledning er vurderet som hjælpsom af 42 personer og har en gennemsnitlig bedømmelse på 4.2 stjerner ud af 21.5 anmeldelser. Har du et spørgsmål om Focal FDP 4.600 V2, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/8

POWER PER CHANNEL

• 4 x 150 wRMS into 4 ohms @ 1% THD

• 4 x 200 wRMS into 2 ohms @ 1% THD

• 2 x 400 wRMS Bridged into 4 ohms @ 1% THD

DO NOT Bridge into 2 ohms

All power ratings are at 14.4v DC.

ROUTE SWITCH

• 1+2 = All four RCA inputs are used.

• 3+4 = Input signal on channels 3+4 are routed to channels 1+2. Use this mode when you need a band pass filter

on all four channels.

Recommended when bridging channels 1, 2, 3, 4.

The controls still function.LEVEL

• Copy = Input signal and ﬁlters on channels 3+4 are copied to channels 1+2. Use this mode when you need a band

pass ﬁlter on all four channels.

Recommended when bridging channels 1,2,3,4.

The controls still function. LEVEL

CHANNELS 1 & 2 CROSSOVER CONFIGURATION

• Flat: Full Range Signal. No crossover filter used.

• HP: Activates the High Pass Filter for a midbass or tweeter.

CHANNELS 3 & 4 CROSSOVER CONFIGURATION

• Flat: Full Range Signal. No crossover filter used.

• HP: Activates the High Pass filter.

• LP/BP: Activates the selection of either a Low Pass filter for woofer or a Band Pass filter for midrange.

• MONO Mode: Inputs 3+4 are mixed to mono for bridge mode operation. If 1+2 ROUTE is set to COPY then 1+2

will also be mono subwoofer and the remote volume control will control level.

The subwoofer remote volume control is activated. There is a clip distortion light on the remote volume control.

If you see this light on, reduce volume until the light goes out so that you do not damage your speaker.

AUTOMATIC POWER TURN ON/OFF

1. The best way to automatically turn the amplifier power on and off is to use the REM wire from your source radio

connected to the REM amplifier terminal.Band Pass for a subwoofer or midbass of a 3 way speaker.

2. If your original equipment stereo or source radio has a BTL amplifier then the RCA inputs have an auto turn

on sensing circuit. When you connect the high level BTL speaker wires to the RCA input the REM wire is not

necessary.

FDP 4.600 V2: FOUR CHANNEL AMPLIFIER

OPERATION / CONFIGURATION MANUAL

RCA INPUT, BOTH LOW LEVEL AND HIGH LEVEL

• The amplifier LEVEL control has sufficient adjustment range for both low level and high level input into the RCA

jacks. A factory source radio that does not have RCA output, using the wires that are connected to the speakers,

can be directly connected to the RCA jacks when the amplifier control is adjusted to 8V.LEVEL

SETTING LEVEL

• The best way to set system levels is to use a D’Amore Engineering DD-1 and test signals.

Follow their gain overlap instructions.

• Set the amplifier control to minimum before you turn on the amplifier for the first time.LEVEL

• For lowest distortion and lowest noise the ampliﬁer should be set at the lowest setting that yields LEVEL

sufﬁcient loudness without distortion. For lowest noise your source radio volume control should be near

maximum that does cause distortion.NOT

• To ﬁnd the best ampliﬁer setting if you are NOT using a DD-1: LEVEL

1) With the ampliﬁer at minimum, slowly increase the source radio volume until you hear distortion. Then LEVEL

turn it down to until the distortion stops.

2) Next, slowly turn up the ampliﬁer control to the maximum desired loudness, or until the red LED LEVEL

light ﬂashes on the music’s ocassional peaks. (The LED turns on when there is distortion that can damage your

speakers.) Listen very carefully and turn down the ampliﬁer control if you hear any distortion.LEVEL

FDP 4.600 V2 CONFIGURATION EXAMPLES

4 CHANNEL STEREO NON-BRIDGED (SEE GRAPHIC B1)

• If you have four input wires from the source deck, plug them into inputs 1+2 and 3+4.

Set ROUTE switch to 1+2.

• If you have two input wires from the source deck, plug them into inputs 3+4.

Set ROUTE switch to 3+4.

Set the switch to STEREO.

• If you are NOT using a subwoofer set all switches to flat. If you hear distortion in your woofers set all switch to

HP and adjust all HP frequency until the distortion goes away, this will probably be around 50 Hz to 70 Hz.

RADIO FLAT or HP50Hz

1+250Hz FLAT or HP

STEREO

B1 (4 CHANNEL STEREO NON-BRIDGED)

XOVER

XOVER XOVER

XOVER

Produkt Specifikationer

Mærke:	Focal
Kategori:	Modtager
Model:	FDP 4.600 V2

Har du brug for hjælp?

Hvis du har brug for hjælp til Focal FDP 4.600 V2 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Modtager Focal Manualer

Focal FDP 1.900V2 Manual

28 August 2024

Focal FPX 1.100 Manual

21 August 2024

Focal FPS 4160 Manual

21 August 2024

Focal FDP 6.900 Manual

20 August 2024

Focal FDP 6.900 V2 Manual

19 August 2024

Focal FDS 2.350 Manual

19 August 2024

Focal FPS 2160 Manual

19 August 2024

Focal FDP 4.600 Manual

19 August 2024

Focal FDP 1.2000 Manual

19 August 2024

Focal FDS 1.350 Manual

19 August 2024

Modtager Manualer

Nyeste Modtager Manualer

Albrecht HAE75 Manual

1 August 2025

CYP AU-A220 Manual

30 Juli 2025

Sirus I-Amp 8.150T Manual

30 Juli 2025

AER Colourizer 2 Manual

30 Juli 2025

Sirus I-Amp 1.300T Manual

30 Juli 2025

PAC AP4-FD32 Manual

30 Juli 2025

CYP PUV-1540S-RX Manual

30 Juli 2025

ART USB Dual Pre Manual

29 Juli 2025

SSL Pure Drive Quad Manual

29 Juli 2025

SSL Pure Drive Octo Manual

29 Juli 2025