Focal FDP 4.600 Manual

Focal Modtager FDP 4.600

Læs gratis den danske manual til Focal FDP 4.600 (8 sider) i kategorien Modtager. Denne vejledning er vurderet som hjælpsom af 24 personer og har en gennemsnitlig bedømmelse på 4.9 stjerner ud af 12.5 anmeldelser. Har du et spørgsmål om Focal FDP 4.600, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/8

POWER PER CHANNEL:

• 4 x 150 wRMS @ 4ohms

• 4 x 200 wRMS @ 2ohms

• 2 x 400 wRMS (Bridged @ 4ohms)

ROUTE SWITCH

• 1+2 = All four RCA inputs are used.

• 3+4 = Input signal on channels 3+4 are routed to channels 1+2. Use this mode when you need a band pass filter

on all four channels.

Recommended when bridging channels 1, 2, 3, 4.

The level controls still function.

• Copy = Input signal and ﬁlters on channels 3+4 are copied to channels 1+2. Use this mode when you need a band

pass ﬁlter on all four channels.

Recommended when bridging channels 1,2,3,4.

The level controls still function.

CHANNELS 1 & 2 CROSSOVER CONFIGURATION

• Flat: Full Range Signal. No crossover filter used.

• HP: Activates the High Pass Filter for a midbass or tweeter.

CHANNELS 3 & 4 CROSSOVER CONFIGURATION

• Flat: Full Range Signal. No crossover filter used.

• HP: Activates the High Pass filter.

• LP/BP: Activates the selection of either a Low Pass filter for woofer or a Band Pass filter for midrange.

• MONO Mode: Inputs 3+4 are mixed to mono for bridge mode operation. If 1+2 ROUTE is set to COPY then 1+2

will also be mono subwoofer and the remote volume control will control level.

The subwoofer remote volume control is activated. There is a clip distortion light on the remote volume control.

If you see this light on, reduce volume until the light goes out so that you do not damage your speaker.

AUTOMATIC POWER TURN ON/OFF

1. The best way to automatically turn the amplifier power on and off is to use the REM wire from your source radio

connected to the REM amplifier terminal.Band Pass for a subwoofer or midbass of a 3 way speaker.

2. If your original equipment stereo or source radio has a BTL amplifier then the RCA inputs have an auto turn

on sensing circuit. When you connect the high level BTL speaker wires to the RCA input the REM wire is not

necessary.

FDP 4.600 : FOUR CHANNEL AMPLIFIER

Operation / Configuration

Produkt Specifikationer

Mærke:	Focal
Kategori:	Modtager
Model:	FDP 4.600

Har du brug for hjælp?

Hvis du har brug for hjælp til Focal FDP 4.600 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Modtager Focal Manualer

Focal FDP 1.900V2 Manual

28 August 2024

Focal FPX 1.100 Manual

21 August 2024

Focal FPS 4160 Manual

21 August 2024

Focal FDP 6.900 Manual

20 August 2024

Focal FDP 6.900 V2 Manual

19 August 2024

Focal FDS 2.350 Manual

19 August 2024

Focal FPS 2160 Manual

19 August 2024

Focal FDP 4.600 Manual

19 August 2024

Focal FDP 1.2000 Manual

19 August 2024

Focal FDS 1.350 Manual

19 August 2024

Modtager Manualer

Nyeste Modtager Manualer

Jensen JA5CH Manual

1 November 2025

Jensen JA4CH Manual

31 Oktober 2025

QFX FX-180 Manual

31 Oktober 2025

Monacor PA-4500DX Manual

31 Oktober 2025

Alpine iLX-W670S Manual

29 Oktober 2025

Jensen JA2CH Manual

29 Oktober 2025

Kramer WP-DEC7 Manual

17 Oktober 2025

FBT MXA 3120 Manual

17 Oktober 2025

Rotel C8 Manual

15 Oktober 2025

Rotel RA-11 Manual

15 Oktober 2025