Forte Lighting 2745-06 Manual


Læs gratis den danske manual til Forte Lighting 2745-06 (1 sider) i kategorien Lys. Denne vejledning er vurderet som hjælpsom af 2 personer og har en gennemsnitlig bedømmelse på 4.5 stjerner ud af 1.5 anmeldelser. Har du et spørgsmål om Forte Lighting 2745-06, eller vil du spørge andre brugere om produktet?

Side 1/1
2745-06
Carefully remove all contents from the carton. See the
important notes above. Shut off the power at the circuit
breaker and completely remove the old fixture from the
ceiling, including the old crossbar. Remove the crossbar
assembly from the bag. The crossbar (B) contains several
pairs of threaded holes. Find the pair of holes that matches
the spacing of the holes on the junction box and the fixtures
crossbar (B). You may need to tighten nuts (C) to hold these
screws in place. Pull the house wires through the center of
the crossbar (B). Place the crossbar (B) over the junction box
so that mounting screws (A) are vertical and aligned with
the hole locations on the fixtures canopy (F). Secure the
crossbar (B) to the junction box by tightening the screws.
Cover the junction box with canopy (F) by tightening nuts
(H) onto the exposed mounting screws (A).
W A R N I N G! S H U T POW ER OFF AT FUSE OR CIRCUIT BREAKER
BEFORE INSTALLATION
AVERTISSEMENT! COUPER LE COURANT AU NIVEAU DES FUSIBLES OU DU DIS JONCTEUR.
CLEANING TIPS
Treat the fixture gently! Regular cleaning will reduce the need of deep cleaning. For regular cleaning, turn off the lighting and wipe down
the fixture with a clean lint-free cotton or microfiber cloth. Never spray cleaner directly onto the fixture.
Each fixture includes two 18-inch rods (K), two 12-inch
rode (L), and two 6-inch rods (M). Determine the correct
number of rods needed for a proper hanging height. To
lengthen the fixture, add additional rods. If additional
rods are needed, contact the place of purchase to order. To
shorten the fixture, trim the wires to the desired length.
Unscrew the ring (O) to release the glass fitter (P). Tilt and rotate the
glass shade (R) so that the glass holder (Q) into glass shade (R).
Drop glass fitter (P) and secure with the ring (H) . Restore power to
the circuit at breaker or fuse box.Install light bulb(s) (not included) in
accordance with the fixtures specification. Do not exceed the
recommended maximum wattage.
These instructions are provided for your safety. It is very important to read them carefully and completely before beginning
installation of the lighting fixture.We strongly suggest that all direct-wired fixture be installed by a qualified and licensed
electrician.
Have an assistant support the fixtures weight while working
o
n the wiring. Attach the fixtures wires to the power supply
w
ires from the junction box. Connect the black wire to black
(
or smooth); the white wire with the white (or ribbed); the
g
round wire with the ground (green or copper). Twist the end
o
f the wire pairs together and twist on a wire connector. Make
s
ure all twists are in the same direction. If there is no ground
w
ire(green or copper) from the junction box, locate a ground
s
crew (E) on the crossbar (B) and wrap the fixtures ground
w
ire around the green ground screw (E). Use a screwdriver to
t
ighten the ground screw (E) onto the crossbar(B). Tuck all
wires neatlyinto the junction box.


Produkt Specifikationer

Mærke: Forte Lighting
Kategori: Lys
Model: 2745-06

Har du brug for hjælp?

Hvis du har brug for hjælp til Forte Lighting 2745-06 stil et spørgsmål nedenfor, og andre brugere vil svare dig