Forte Lighting 2743-03 Manual

Forte Lighting Lys 2743-03

Læs gratis den danske manual til Forte Lighting 2743-03 (1 sider) i kategorien Lys. Denne vejledning er vurderet som hjælpsom af 3 personer og har en gennemsnitlig bedømmelse på 4.1 stjerner ud af 2 anmeldelser. Har du et spørgsmål om Forte Lighting 2743-03, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/1

2743-03 2743-06

Connect the lamp holder (N) to the lamp holder (P) and lock it

with (T). Secure shade (Q) onto the socket (O) by screwing

socket ring (R) tightly. Install light bulb (not included) in

accordance with the fixture’s specifications. Do not exceed

the recommended maximum wattage.

Carefully remove all contents from the carton. See the

important notes above. Shut off the power at the circuit

breaker and completely remove the old fixture from the

ceiling, including the old crossbar. Remove the crossbar

assembly from the bag. Crossbar (B) contains several

pairs of threaded holes. Find the pair of holes that matches

the spacing of the holes on the junction box and the fixture’s

canopy. Two mounting screws (A) should be attached to

crossbar (B). You may need to tighten nuts (C) to hold these

screws in place. Pull the house wires through the center of

crossbar (B). Place crossbar (B) over the junction box so

that mounting screws (A) are vertical and aligned with

the hole locations on the fixture’s canopy (F). Secure

crossbar (B) to the junction box by tightening the screws.

crossbar

There are an 18 inch rod (K), a 12 inch rod (L), and a 6

inch rod (M) included for each fixture. Rod (L) is wired.

Determine the correct number of rods needed for proper

hanging height. To lengthen the fixture, add additional rods.

If additional rods are needed, contact the place of purchase

to order. To shorten the fixture, trim the wires to the desired

length, leave at least 8 to 10 inches of wire in addition to the

desired length and slide any excess rods off to discard. Keep

in mind that you must use at least the provided 6 inch rod (M)

Push canopy (F) up to the ceiling and tighten the deco nuts (H)

onto the exposed mounting screws (A).

to hang the fixture. Thread the wires through the rods and

pull the wires until taut before connecting the rods together.

Thread bottom rod (M) onto nipple (N) on the fixture. Thread

the nipple of the top rod onto swivel post (I) of canopy (F).

Pull the fixture wires through the top of the canopy.

SMOOTH

Produkt Specifikationer

Mærke:	Forte Lighting
Kategori:	Lys
Model:	2743-03

Har du brug for hjælp?

Hvis du har brug for hjælp til Forte Lighting 2743-03 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Lys Forte Lighting Manualer

Forte Lighting 5745-02 Manual

21 December 2025

Forte Lighting 2743-03 Manual

21 December 2025

Forte Lighting 5743-02 Manual

21 December 2025

Forte Lighting 2748-05 Manual

21 December 2025

Forte Lighting 2745-03 Manual

21 December 2025

Forte Lighting 7120-05 Manual

20 December 2025

Forte Lighting 2760-03 Manual

20 December 2025

Forte Lighting 7116-04 Manual

20 December 2025

Forte Lighting 5748-02 Manual

20 December 2025

Forte Lighting 2664-04 Manual

20 December 2025

Lys Manualer

Nyeste Lys Manualer

Alora Marcel EW464002 Manual

21 December 2025

Vaxcel Grant P0289 Manual

21 December 2025

Bellevue Novo VXP49432ORB Manual

21 December 2025

Progress Lighting P500508 Manual

21 December 2025

Vaxcel Alto C0218 Manual

21 December 2025

Vaxcel Canton C0270 Manual

21 December 2025

Progress Lighting P3053 Manual

21 December 2025

Vaxcel W0493 Manual

21 December 2025

Vaxcel P0105 Manual

21 December 2025

Bellevue Kash VXCF80058NB Manual

21 December 2025