Forte Lighting 7116-04 Manual


Læs gratis den danske manual til Forte Lighting 7116-04 (1 sider) i kategorien Lys. Denne vejledning er vurderet som hjælpsom af 3 personer og har en gennemsnitlig bedømmelse på 4.8 stjerner ud af 2 anmeldelser. Har du et spørgsmål om Forte Lighting 7116-04, eller vil du spørge andre brugere om produktet?

Side 1/1
7116-04
Install bulb(s) (not included) in accordance with the fixtures
specifications. Do not exceed the recommended maximum wattage.
Each fixture includes two 18-inch rods (K), two 12-inch
rode (L), and two 6-inch rods (M). Determine the correct
number of rods needed for a proper hanging height. To
lengthen the fixture, add additional rods. If additional
rods are needed, contact the place of purchase to order. To
leave at least 8 to 10 inches of wire beside to the desired length,
and slide any the extra rods off the fixtures wires to discard. Keep
in mind that you must use the provided 6-inch rods (M) to hang
the fixture at least. Thread the wires through the rods and pull the
wires until it is taut before connecting the rods together. Screw
bottom rods (M) onto nipples (N) on the fixture. Screw the nipples
of the top rods into the swivel posts (I) of the canopy (F). Pull the
fixture wires through the top of the canopy.
Remove all contents from the carton. See the important
notes above carefully. Shut off the power at the circuit
breaker and completely remove the old fixture from the
ceiling, including the old crossbar. Remove the crossbar
kits from the bag. Crossbar (B) contains several pairs of
threaded holes. Find the pair of holes that matches the
spacing of the holes on the junction box and the fixtures
canopy. Two mounting screws (A) should be attached to
crossbar (B). You may need to tighten nuts (C) to hold
these screws in place. Pull the house wires through the
center of the crossbar (B). Place the crossbar (B) over the
junction box so that the mounting screws (A) are vertical
and aligned with the hole locations on the fixtures
canopy (F). Secure crossbar (B) to the junction box by
tightening the screws.
CLEANING TIPS
Treat the fixture gently! Regular cleaning will reduce the need of deep cleaning. For regular cleaning, turn off the lighting and wipe down
the fixture with a clean lint-free cotton or microfiber cloth. Never spray cleaner directly onto the fixture.
W A R N I N G! S H U T POW ER OFF AT FUSE OR CIRCUIT BREAKER
BEFORE INSTALLATION
AVERTISSEMENT! COUPER LE COURANT AU NIVEAU DES FUSIBLES OU DU DIS JONCTEUR.
These instructions are provided for your safety. It is very important to read them carefully and completely before beginning
installation of the lighting fixture.We strongly suggest that all direct-wired fixture be installed by a qualified and licensed
electrician.
Have an assistant support the fixtures weight while working on
t
he wiring. Attach the fixtures wires to the power supply wires
f
rom the junction box. Connect the black to black( or smooth);
t
he white wire with the white (or ribbed); the ground wire with
t
heground (green or copper). Twist the end of the wire pairs together
a
nd twist on a wire connector. Make sure all twists are in the same
d
irection. If there is no ground wire(green or copper) from thejunction
b
ox, locate the ground screw (E) on the crossbar (B) and wrap the
f
ixtures ground wire around the green ground screw (E). Use a
s
crewdriver to tighten the ground screw (E) onto the crossbar(B).
Tuck all wires neatly into the junction box.


Produkt Specifikationer

Mærke: Forte Lighting
Kategori: Lys
Model: 7116-04

Har du brug for hjælp?

Hvis du har brug for hjælp til Forte Lighting 7116-04 stil et spørgsmål nedenfor, og andre brugere vil svare dig