Forte Lighting 2664-04 Manual

Forte Lighting Lys 2664-04

Læs gratis den danske manual til Forte Lighting 2664-04 (1 sider) i kategorien Lys. Denne vejledning er vurderet som hjælpsom af 2 personer og har en gennemsnitlig bedømmelse på 4.7 stjerner ud af 1.5 anmeldelser. Har du et spørgsmål om Forte Lighting 2664-04, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/1

2664-04

Secure glass shade (Q) onto the socket (P) by screwing socket

ring (R) tightly. Install light bulb (not included) in accordance

with the fixture’s specifications. Do not exceed the recommended

maximum wattage.

There are two 18 inch rods (K), two 12 inch rods (L), and

two 6 inch rods (M) included for each fixture. Determine

the correct number of rods needed for proper hanging height.

To lengthen the fixture, add additional rods. If additional

rods are needed, contact the place of purchase to order. To

shorten the fixture, trim the wires to the desired length,

leave at least 8 to 10 inch of wire in addition to the desired

length and slide any excess rods off the fixture’s wires to

discard. Keep in mind that you must use at least the provided

6 inch rods (M) to hang the fixture. Thread the wires through

the rods and pull the wires until taut before connecting the

rods together. Screw bottom rods (M) onto nipples (N) on the

fixture. Screw the nipples of the top rods into swivel posts (I)

of canopy (F). Pull the fixture wires through the top of the

canopy.

Carefully remove all contents from the carton. See the

important notes above. Shut off the power at the circuit

breaker and completely remove the old fixture from the

ceiling, including the old crossbar. Remove the crossbar

assembly from the bag. Crossbar (B) contains several

pairs of threaded holes. Find the pair of holes that matches

the spacing of the holes on the junction box and the fixture’s

canopy. Two mounting screws (A) should be attached to

crossbar (B). You may need to tighten nuts (C) to hold

these screws in place. Pull the house wires through the

center of crossbar (B). Place crossbar (B) over the junction

box so that mounting screws (A) are vertical and aligned

with the hole locations on the fixture’s canopy (F). Secure

crossbar (B) to the junction box by tightening the screws.

screw (E) on crossbar (B) and wrap the fixture’s ground

wire around the green ground screw (E). Use screwdriver

to secure ground screw (E) onto crossbar (B). Tuck all wires

neatly into the junction box.

Produkt Specifikationer

Mærke:	Forte Lighting
Kategori:	Lys
Model:	2664-04

Har du brug for hjælp?

Hvis du har brug for hjælp til Forte Lighting 2664-04 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Lys Forte Lighting Manualer

Forte Lighting 7120-05 Manual

20 December 2025

Forte Lighting 2760-03 Manual

20 December 2025

Forte Lighting 7116-04 Manual

20 December 2025

Forte Lighting 5748-02 Manual

20 December 2025

Forte Lighting 2664-04 Manual

20 December 2025

Forte Lighting 2759-03 Manual

20 December 2025

Forte Lighting 2763-01 Manual

20 December 2025

Forte Lighting 7116-01 Manual

20 December 2025

Forte Lighting 5743-03 Manual

20 December 2025

Forte Lighting 2405-01 Manual

9 December 2025

Lys Manualer

Nyeste Lys Manualer

NUVO 65/538R1 Manual

20 December 2025

Progress Lighting P2919 Manual

20 December 2025

NUVO 62/469 Manual

20 December 2025

Vaxcel Harper W0472 Manual

20 December 2025

Vaxcel Anson P0413 Manual

20 December 2025

Vaxcel Pryce W0502 Manual

20 December 2025

Regina Andrew Redford 17-1019 Manual

20 December 2025

Vaxcel Euclid P0317 Manual

20 December 2025

Progress Lighting P300437 Manual

20 December 2025

Vaxcel Milano P0178 Manual

20 December 2025