Forte Lighting 2405-01 Manual

Forte Lighting Lys 2405-01

Læs gratis den danske manual til Forte Lighting 2405-01 (1 sider) i kategorien Lys. Denne vejledning er vurderet som hjælpsom af 3 personer og har en gennemsnitlig bedømmelse på 4.5 stjerner ud af 2 anmeldelser. Har du et spørgsmål om Forte Lighting 2405-01, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/1

2405-01

Secure shade (Q) onto the socket (P) by screwing socket

ring (R) tightly. Install light bulb (not included) in accordance

with the fixture’s specifications. Do not exceed the recommended

maximum wattage.

Carefully remove all contents from the carton. See the

important notes above. Shut off the power at the circuit

breaker and completely remove the old fixture from the

ceiling, including the old crossbar. Remove the crossbar

assembly from the bag. Crossbar (B) contains several

pairs of threaded holes. Find the pair of holes that matches

the spacing of the holes on the junction box and the fixture’s

canopy. Two mounting screws (A) should be attached to

crossbar (B). You may need to tighten nuts (C) to hold these

screws in place. Pull the house wires through the center of

crossbar (B). Place crossbar (B) over the junction box so

that mounting screws (A) are vertical and aligned with

the hole locations on the fixture’s canopy (F). Secure

crossbar (B) to the junction box by tightening the screws.

crossbar

There are an 18 inch rod (K), a 12 inch rod (L), and a 6

inch rod (M) included for each fixture. Rod (L) is wired.

Determine the correct number of rods needed for proper

hanging height. To lengthen the fixture, add additional rods.

If additional rods are needed, contact the place of purchase

to order. To shorten the fixture, trim the wires to the desired

length, leave at least 8 to 10 inches of wire in addition to the

desired length and slide any excess rods off to discard. Keep

in mind that you must use at least the provided 6 inch rod (M)

Push canopy (F) up to the ceiling and tighten the deco nuts (H)

onto the exposed mounting screws (A).

to hang the fixture. Thread the wires through the rods and

pull the wires until taut beforeconnecting the rods togethre.

Thread bottom rod (M) onto nipple (N) on the fixture. Thread

the nipple of the top rod onto swivel post (I) of canopy (F).

Pull the fixture wires through the top of the canopy.

Produkt Specifikationer

Mærke:	Forte Lighting
Kategori:	Lys
Model:	2405-01

Har du brug for hjælp?

Hvis du har brug for hjælp til Forte Lighting 2405-01 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Lys Forte Lighting Manualer

Forte Lighting 2405-01 Manual

9 December 2025

Forte Lighting 2680-01 Manual

9 December 2025

Forte Lighting 7117-06 Manual

9 December 2025

Forte Lighting 2751-01 Manual

8 December 2025

Forte Lighting 7100-04 Manual

8 December 2025

Forte Lighting 5197-01 Manual

8 December 2025

Forte Lighting 2770-01 Manual

8 December 2025

Forte Lighting 7116-05 Manual

8 December 2025

Forte Lighting 7210-01 Manual

8 December 2025

Forte Lighting 5745-03 Manual

8 December 2025

Lys Manualer

Nyeste Lys Manualer

Kichler 15005MST Manual

11 December 2025

Robert Abbey RR43X Manual

10 December 2025

Dainolite FLY-2211LEDT Manual

10 December 2025

Dals MSL10 Manual

10 December 2025

AFX TPWW70050LWH Manual

10 December 2025

Robert Abbey CI21X Manual

10 December 2025

Kichler 15079BKT Manual

10 December 2025

Quoizel PCELW8532MBK Manual

10 December 2025

NUVO 65/671 Manual

10 December 2025

Dals LEDDOWNG3-CC Manual

10 December 2025