GARDE 181COM2BST Manual

GARDE Dåseåbner 181COM2BST

Læs gratis den danske manual til GARDE 181COM2BST (1 sider) i kategorien Dåseåbner. Denne vejledning er vurderet som hjælpsom af 2 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 1.5 anmeldelser. Har du et spørgsmål om GARDE 181COM2BST, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/1
08/2023
IT IS RECOMMENDED THE KNIFE AND GEAR ARE
REPLACED AT THE SAME TIME FOR OPTIMAL PERFORMANCE.
1. Insert the can opener into the base. The base will be
needed for leverage while removing the gear.
2. Use a at head screwdriver to hold the gear in place by
jamming the head of the screw driver into the teeth of the
old gear. You will need to apply enough pressure to hold
the gear in place.
counter clockwise. You should feel the tension in the
spring ease up and the gear will come loose after a few
turns.
4. Remove the old gear and keep the washer. Insert the
new gear with the washer on top. Turn the handle clock-
wise until the handle connects to the shaft below the gear.
The spring should be tense now and the can opener is
ready to use.
(181COM2GEAR)
REPLACING THE GEAR
1. Using either a Phillips or at head screw driver to remove
the 2 screws that connect the knife to the opener.
2. Remove and discard the old knife while keeping the
knife support plate.
3. Position the new knife in line with the holes and place the
support plate on top of the knife.
4. Use the screwdriver to tighten the screws.
(181COM2KNIFE)
REPLACING THE KNIFE
The can opener’s surface should be cleaned regularly using
a food safe sanitizer.
Recommendation:
Noble Chemical’s QuikSan Sanitizer and Disinfectant (147QUIKSAN)
Use a toothbrush-style brush to ensure you are able to reach
the crevices around the knife.
Recommendation:
Scrubble Products 7¼ Utility Brush Stainless Steel Bristles (27140675)
After cleaning, apply a food safe oil to the gear to keep it
turning smoothly.
Recommendation:
Petrol-Gel Food Grade Sanitary Lubricant - 4 oz. Tube (401PETROGEL)
CLEANING / MAINTENANCE
USE CAUTION WHEN CLEANING
ITEM NUMBER DESCRIPTION
181COBASE2 Steel Base
181COM2KNIFE Knife
181COM2GEAR Gear
181COM2SCRW Knife Screws
These parts can be purchased from the same location as the can opener.
REPLACEMENT PARTS
1. Position the can you are opening on the counter on top of
the base with the lip of the can touching the can opener.
2. Line up the knife on the inside lip of the can. With the
handle upright, punch down so the knife punctures the
can’s lid.
3. Push the handle down so it is parallel with the counter
and begin turning the handle to open the can.
4. Once the lid is separated, safely remove it from the can.
Avoid touching the sharp edges of the lid created while
opening the can.
5. Pull the can opener up and move the can away from the
opener.
USING YOUR NEW CAN OPENER
The Garde Standard Duty Can Opener is made of durable cast
iron construction with a rust-resistant coating. It can be used to
open cans of all sizes, including #10 Cans. Bases are sold sepa-
rately and are required for proper leverage when opening cans.
ABOUT
Please read and comply with the instructions listed on this document. To get the
best service life and performance from your machine, clean it thoroughly before
and after each use by following the instructions listed below. Minimize the use of
alkaline cleaners as they may dull the nish and cause pitting.
181COM2BST - Plated Steel Base
181COM2NB - No Base
MODELS
STANDARD DUTY CAN OPENERS
QUICK START GU

Produkt Specifikationer

Mærke: GARDE
Kategori: Dåseåbner
Model: 181COM2BST

Har du brug for hjælp?

Hvis du har brug for hjælp til GARDE 181COM2BST stil et spørgsmål nedenfor, og andre brugere vil svare dig


Dåseåbner GARDE Manualer

GARDE

GARDE 181COM2NB Manual

17 September 2025
GARDE

GARDE 181COM2BST Manual

17 September 2025

Dåseåbner Manualer

Nyeste Dåseåbner Manualer

Vollrath

Vollrath BCO-5000 Manual

27 August 2025
Garde XL

Garde XL 181CONSFNB Manual

27 August 2025
Vollrath

Vollrath BCO-1 Manual

27 August 2025
Garde XL

Garde XL 181CONSFBST Manual

25 August 2025
Edlund

Edlund S-11 Manual

25 August 2025
Edlund

Edlund U-12 Manual

25 August 2025
Vollrath

Vollrath BCO-6000 Manual

25 August 2025
Edlund

Edlund G-2 Manual

25 August 2025
Vollrath

Vollrath BCO-3000 Manual

25 August 2025
Nemco

Nemco 56050-1 Manual

25 August 2025