Garmin EchoMAP CHIRP 72 Manual

Garmin Ikke kategoriseret EchoMAP CHIRP 72

Læs gratis den danske manual til Garmin EchoMAP CHIRP 72 (6 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 63 personer og har en gennemsnitlig bedømmelse på 4.5 stjerner ud af 32 anmeldelser. Har du et spørgsmål om Garmin EchoMAP CHIRP 72, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/6

echoMAP™ CHIRP

70/90 Series

Installation Instructions

Important Safety Information

WARNING

See the guide in the Important Safety and Product Information

product box for product warnings and other important

information.

When connecting the power cable, do not remove the in-line

fuse holder. To prevent the possibility of injury or product

damage caused by fire or overheating, the appropriate fuse

must be in place as indicated in the product specifications. In

addition, connecting the power cable without the appropriate

fuse in place voids the product warranty.

CAUTION

Always wear safety goggles, ear protection, and a dust mask

when drilling, cutting, or sanding.

NOTICE

When drilling or cutting, always check what is on the opposite

side of the surface.

To obtain the best performance and to avoid damage to your

boat, install the device according to these instructions.

Read all installation instructions before proceeding with the

installation. If you experience difficulty during the installation,

contact Garmin® Product Support.

Software Update

You may need to update the device software when you install

the device or add an accessory to the device.

Loading the New Software on a Memory Card

You must copy the software update to a memory card using a

computer that is running Windows® software.

NOTE: You can contact Garmin customer support to order a

preloaded software update card if you do not have a computer

with Windows software.

1Insert a memory card into the card slot on the computer.

2Go to .www.garmin.com/support/software/marine.html

3Select next to the software bundle that Download

corresponds with your device.

4Read and agree to the terms.

5Select .Download

6If necessary, select .Run

7If necessary, select the drive associated with the memory

card, and select > .Next Finish

Updating the Device Software

Before you can update the software, you must obtain a

software-update memory card or load the latest software onto a

memory card.

1Turn on the chartplotter.

2After the home screen appears, insert the memory card into

the card slot.

NOTE: In order for the software update instructions to

appear, the device must be fully booted before the card is

inserted.

3Follow the on-screen instructions.

4Wait several minutes while the software update process

completes.

5When prompted, leave the memory card in place and restart

the chartplotter manually.

6Remove the memory card.

NOTE: If the memory card is removed before the device

restarts fully, the software update is not complete.

Registering Your Device

Help us better support you by completing our online registration

today.

• Go to .http://my.garmin.com

• Keep the original sales receipt, or a photocopy, in a safe

place.

Contacting Garmin Product Support

• Go to for in-country support www.garmin.com/support

information.

• In the USA, call 913-397-8200 or 1-800-800-1020.

• In the UK, call 0808 238 0000.

• In Europe, call +44 (0) 870 850 1241.

Tools Needed

• Drill and drill bits

• #2 Phillips screwdriver

• Jigsaw or rotary tool

• File and sandpaper

• Marine sealant (optional)

Mounting Considerations

The device can be mounted using the included bracket, or it can

be mounted flush with the dashboard using a flush-mount kit

(may be sold separately).

Before permanently installing any part of your device, you

should plan the installation by determining the location of the

various components.

• The mounting location must provide a clear view of the

screen and access to the keys on the device.

• The mounting location must be sturdy enough to support the

device and the mount.

• The cables must be long enough to connect the components

to each other and to power.

• The cables can be routed under the bail mount or behind the

device.

• To avoid interference with a magnetic compass, the device

should not be installed closer to a compass than the

compass-safe distance value listed in the product

specifications.

December 2015 Printed in Taiwan 190-01952-02_0A

Bail Mounting the Device

NOTICE

If you are mounting the bracket on fiberglass with screws, it is

recommended to use a countersink bit to drill a clearance

counterbore through only the top gel-coat layer. This will help to

avoid any cracking in the gel-coat layer when the screws are

tightened.

Stainless-steel screws may bind when screwed into fiberglass

and overtightened. Garmin recommends applying an anti-seize

lubricant to the screws before installing them.

1Select the mounting hardware appropriate for your mounting

surface and for the bail-mount bracket.

2Using the bail-mount bracket as a template, mark the pilot

holes through the screw holes.

3Using a drill bit appropriate for the mounting hardware, drill

the four pilot holes.

4Using the selected mounting hardware, secure the bail-mount

bracket to the mounting surface.

5Install the bail-mount knobs À on the sides of the device.

6Place the device into the cradle Á.

7Place the cradle in the bail-mount bracket and tighten the

bail-mount knobs.

Flush Mounting the Device

NOTICE

Be careful when cutting the hole to flush mount the device.

There is only a small amount of clearance between the case and

the mounting holes, and cutting the hole too large could

compromise the stability of the device after it is mounted.

Using a metal pry tool such as a screwdriver can damage the

trim caps and the device. Use a plastic pry tool when possible.

You can mount the device in your dashboard using the flush-

mount template and appropriate hardware.

1Trim the template and make sure it fits in the location where

you want to mount the device.

2Secure the template to the mounting location.

3Using a 9.5 mm (3/8 in.) drill bit, drill one or more of the holes

inside the corners of the solid line on the template to prepare

the mounting surface for cutting.

4Using a jigsaw or rotary cutting tool, cut the mounting surface

along the inside of the solid line indicated on the template.

5Place the device into the cutout to test the fit.

6If necessary, use a file and sandpaper to refine the size of

the hole.

7If your device has trim caps, use a pry tool, such as a flat

piece of plastic or a screwdriver, to carefully pry up the

corners of the trim caps À, slide the pry tool to the center

Á,

and remove the trim caps.

8Ensure the mounting holes on the device line up with the pilot

holes on the template.

9If the mounting holes on the device do not line up with the

pilot holes on the template, mark the new pilot-hole locations

on your template.

10Using a 3.2 mm (1/8 in.) drill bit, drill the pilot holes.

11Remove the template from the mounting surface.

12If you will not have access to the back of the device after you

mount it, connect all necessary cables to the device before

placing it into the cutout.

NOTE: To prevent corrosion of the metal contacts, cover

unused connectors with weather caps.

13Install the rubber gasket pieces on the back of the device.

The pieces of the rubber gasket have adhesive on the back.

Make sure you remove the protective liner before installing

them on the device.

14Securely connect each cable to a port on the cradle.

15Place the device into the cutout.

16Secure the device to the mounting surface using the included

screws.

17Install the trim caps by snapping them in place around the

edges of the device.

Installing the Cables and Connectors

Wiring to Power

1Route the power cable from the swivel mount to the boat

battery or fuse block.

Produkt Specifikationer

Mærke:	Garmin
Kategori:	Ikke kategoriseret
Model:	EchoMAP CHIRP 72

Har du brug for hjælp?

Hvis du har brug for hjælp til Garmin EchoMAP CHIRP 72 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Garmin Manualer

Garmin Approach CT1 Manual

26 Februar 2025

Garmin Spectra LC302 Manual

9 Januar 2025

Garmin Spectra LC102 Manual

9 Januar 2025

Garmin dēzl Headset 210 Manual

14 November 2024

Garmin Inreach Messenger Plus Manual

11 November 2024

Garmin GMM 170 Manual

4 Oktober 2024

Garmin GMR 18 xHD Manual

4 Oktober 2024

Garmin Edge Power Mount Manual

3 Oktober 2024

Garmin GT30-TH Manual

3 Oktober 2024

Garmin GMR 18 HD+ Manual

30 September 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

ORNO OR-PSU-1675 Manual

15 Juni 2025

EmberGlo ES5CTS Manual

15 Juni 2025

Chapin 8201A Manual

15 Juni 2025

Gourmia GDK2365 Manual

15 Juni 2025

Xiaomi Wireless Mouse 3 Manual

15 Juni 2025

Auray SVRK-12U-D Manual

15 Juni 2025

Aiphone IXGW-TGW Manual

15 Juni 2025

Aiphone AC-2DE Manual

15 Juni 2025

Schlage S280 Manual

15 Juni 2025

Cleveland PGM3002 Manual

15 Juni 2025