Garmin EchoMAP CHIRP 90 Manual

Garmin Ikke kategoriseret EchoMAP CHIRP 90

Læs gratis den danske manual til Garmin EchoMAP CHIRP 90 (6 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 31 personer og har en gennemsnitlig bedømmelse på 4.1 stjerner ud af 16 anmeldelser. Har du et spørgsmål om Garmin EchoMAP CHIRP 90, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/6
echoMAP™ CHIRP
70/90 Series
Installation Instructions
Important Safety Information
WARNING
See the guide in the Important Safety and Product Information
product box for product warnings and other important
information.
When connecting the power cable, do not remove the in-line
fuse holder. To prevent the possibility of injury or product
damage caused by fire or overheating, the appropriate fuse
must be in place as indicated in the product specifications. In
addition, connecting the power cable without the appropriate
fuse in place voids the product warranty.
CAUTION
Always wear safety goggles, ear protection, and a dust mask
when drilling, cutting, or sanding.
NOTICE
When drilling or cutting, always check what is on the opposite
side of the surface.
To obtain the best performance and to avoid damage to your
boat, install the device according to these instructions.
Read all installation instructions before proceeding with the
installation. If you experience difficulty during the installation,
contact Garmin® Product Support.
Software Update
You may need to update the device software when you install
the device or add an accessory to the device.
Loading the New Software on a Memory Card
You must copy the software update to a memory card using a
computer that is running Windows® software.
NOTE: You can contact Garmin customer support to order a
preloaded software update card if you do not have a computer
with Windows software.
1Insert a memory card into the card slot on the computer.
2Go to .www.garmin.com/support/software/marine.html
3Select next to the software bundle that Download
corresponds with your device.
4Read and agree to the terms.
5Select .Download
6If necessary, select .Run
7If necessary, select the drive associated with the memory
card, and select > .Next Finish
Updating the Device Software
Before you can update the software, you must obtain a
software-update memory card or load the latest software onto a
memory card.
1Turn on the chartplotter.
2After the home screen appears, insert the memory card into
the card slot.
NOTE: In order for the software update instructions to
appear, the device must be fully booted before the card is
inserted.
3Follow the on-screen instructions.
4Wait several minutes while the software update process
completes.
5When prompted, leave the memory card in place and restart
the chartplotter manually.
6Remove the memory card.
NOTE: If the memory card is removed before the device
restarts fully, the software update is not complete.
Registering Your Device
Help us better support you by completing our online registration
today.
• Go to .http://my.garmin.com
• Keep the original sales receipt, or a photocopy, in a safe
place.
Contacting Garmin Product Support
• Go to for in-country support www.garmin.com/support
information.
• In the USA, call 913-397-8200 or 1-800-800-1020.
• In the UK, call 0808 238 0000.
• In Europe, call +44 (0) 870 850 1241.
Tools Needed
• Drill and drill bits
• #2 Phillips screwdriver
• Jigsaw or rotary tool
• File and sandpaper
• Marine sealant (optional)
Mounting Considerations
The device can be mounted using the included bracket, or it can
be mounted flush with the dashboard using a flush-mount kit
(may be sold separately).
Before permanently installing any part of your device, you
should plan the installation by determining the location of the
various components.
• The mounting location must provide a clear view of the
screen and access to the keys on the device.
• The mounting location must be sturdy enough to support the
device and the mount.
• The cables must be long enough to connect the components
to each other and to power.
• The cables can be routed under the bail mount or behind the
device.
• To avoid interference with a magnetic compass, the device
should not be installed closer to a compass than the
compass-safe distance value listed in the product
specifications.
December 2015 Printed in Taiwan 190-01952-02_0A
Bail Mounting the Device
NOTICE
If you are mounting the bracket on fiberglass with screws, it is
recommended to use a countersink bit to drill a clearance
counterbore through only the top gel-coat layer. This will help to
avoid any cracking in the gel-coat layer when the screws are
tightened.
Stainless-steel screws may bind when screwed into fiberglass
and overtightened. Garmin recommends applying an anti-seize
lubricant to the screws before installing them.
1Select the mounting hardware appropriate for your mounting
surface and for the bail-mount bracket.
2Using the bail-mount bracket as a template, mark the pilot
holes through the screw holes.
3Using a drill bit appropriate for the mounting hardware, drill
the four pilot holes.
4Using the selected mounting hardware, secure the bail-mount
bracket to the mounting surface.
5Install the bail-mount knobs À on the sides of the device.
6Place the device into the cradle Á.
7Place the cradle in the bail-mount bracket and tighten the
bail-mount knobs.
Flush Mounting the Device
NOTICE
Be careful when cutting the hole to flush mount the device.
There is only a small amount of clearance between the case and
the mounting holes, and cutting the hole too large could
compromise the stability of the device after it is mounted.
Using a metal pry tool such as a screwdriver can damage the
trim caps and the device. Use a plastic pry tool when possible.
You can mount the device in your dashboard using the flush-
mount template and appropriate hardware.
1Trim the template and make sure it fits in the location where
you want to mount the device.
2Secure the template to the mounting location.
3Using a 9.5 mm (3/8 in.) drill bit, drill one or more of the holes
inside the corners of the solid line on the template to prepare
the mounting surface for cutting.
4Using a jigsaw or rotary cutting tool, cut the mounting surface
along the inside of the solid line indicated on the template.
5Place the device into the cutout to test the fit.
6If necessary, use a file and sandpaper to refine the size of
the hole.
7If your device has trim caps, use a pry tool, such as a flat
piece of plastic or a screwdriver, to carefully pry up the
corners of the trim caps À, slide the pry tool to the center
Á,
and remove the trim caps.
8Ensure the mounting holes on the device line up with the pilot
holes on the template.
9If the mounting holes on the device do not line up with the
pilot holes on the template, mark the new pilot-hole locations
on your template.
10Using a 3.2 mm (1/8 in.) drill bit, drill the pilot holes.
11Remove the template from the mounting surface.
12If you will not have access to the back of the device after you
mount it, connect all necessary cables to the device before
placing it into the cutout.
NOTE: To prevent corrosion of the metal contacts, cover
unused connectors with weather caps.
13Install the rubber gasket pieces on the back of the device.
The pieces of the rubber gasket have adhesive on the back.
Make sure you remove the protective liner before installing
them on the device.
14Securely connect each cable to a port on the cradle.
15Place the device into the cutout.
16Secure the device to the mounting surface using the included
screws.
17Install the trim caps by snapping them in place around the
edges of the device.
Installing the Cables and Connectors
Wiring to Power
1Route the power cable from the swivel mount to the boat
battery or fuse block.
2

Produkt Specifikationer

Mærke: Garmin
Kategori: Ikke kategoriseret
Model: EchoMAP CHIRP 90

Har du brug for hjælp?

Hvis du har brug for hjælp til Garmin EchoMAP CHIRP 90 stil et spørgsmål nedenfor, og andre brugere vil svare dig


Ikke kategoriseret Garmin Manualer

Garmin

Garmin Foretrex 701 Ballistic Edition Manual

12 August 2025
Garmin

Garmin Approach CT1 Manual

26 Februar 2025
Garmin

Garmin dēzl Headset 110 Manual

8 Februar 2025
Garmin

Garmin Spectra LC302 Manual

9 Januar 2025
Garmin

Garmin Spectra LC102 Manual

9 Januar 2025
Garmin

Garmin dēzl Headset 210 Manual

14 November 2024
Garmin

Garmin Inreach Messenger Plus Manual

11 November 2024
Garmin

Garmin GMM 170 Manual

4 Oktober 2024
Garmin

Garmin GMR 18 xHD Manual

4 Oktober 2024
Garmin

Garmin Edge Power Mount Manual

3 Oktober 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

AstralPool

AstralPool Niche Switch Manual

18 Oktober 2025
Sungrow

Sungrow SH8.0RT-V113 Manual

18 Oktober 2025
AstralPool

AstralPool Roma Manual

18 Oktober 2025
Evenflo

Evenflo SafeMax Manual

18 Oktober 2025
NEO Tools

NEO Tools 94-002 Manual

18 Oktober 2025
LC-Power

LC-Power Platinum Pro LC1000P V3.1 Manual

17 Oktober 2025
Metz

Metz 130B21-E Manual

17 Oktober 2025
NEO Tools

NEO Tools 99-038 Manual

17 Oktober 2025
FBT

FBT MPU 2120 Manual

17 Oktober 2025
Icy Box

Icy Box IB-MS404-T Manual

17 Oktober 2025