Garmin Fishfinder 80 Manual

Garmin fiskefinder Fishfinder 80

Læs gratis den danske manual til Garmin Fishfinder 80 (3 sider) i kategorien fiskefinder. Denne vejledning er vurderet som hjælpsom af 22 personer og har en gennemsnitlig bedømmelse på 4.9 stjerner ud af 11.5 anmeldelser. Har du et spørgsmål om Garmin Fishfinder 80, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/3

Flush Mount Installation Instructions

Contents:

Mounting Hardware:

A - Foam Rubber Pads (2)

B - M4x40mm Hew Head Screws (4)

C - M4 Hex Nuts (4)

D - Reusable Cable Tie (1)

E - Metal Retaining Brackets (2)

Please read through these instructions thoroughly before attempting installation. Make

sure you completely understand these instructions before you begin. When in doubt, seek

professional assistance. Be sure the cables will reach the unit and transducer location before

beginning installation. Please check the packing list above. If you are missing any items,

please contact your Garmin dealer. Be sure to wear safety goggles and dusk mask when drill-

ing and cutting.

Installing the Flush Mount Pocket

1. Using the supplied Mounting Template locate a suitable mounting location and

tape the template in place. Be sure to check behind the installation area to

avoid cutting or drilling into wiring, cables, etc.

2. Drill a 3/8” hole at the location in di cat ed on the template as a starting point,

then using the Jig Saw, cut the panel along the bold line. Be sure that your

initial cut does not go outside the line that in di cates the inside edge of the

pocket. (Figure 1)

3. Using a file or sandpaper, remove any burrs from the open ing. Test fit the Flush

Mount Pocket and make any ad just ments to correct the fit.

4. Install the two Foam Rubber Pads in the pocket at the locations indicated in

Figure 2. To install the pads, peel the lining off of the back and install with the

sticky side against the pocket.

5. Insert the pocket in the panel (The Garmin logo should be positioned at the

top.) Install a M4 Hex Head Screw through the pocket and the corresponding

hole in the Metal Retaining Bracket. Start a 4mm Hex Nut on the screw. Repeat

the process until all 4 nuts are started (Figure 3). Tighten the M4 nuts using a

7mm wrench or socket.

If operating in a high vibration environment it is recommended

that you use a thread locking compound on the M4 Hex Head Screws.

6. Secure the cable to the rectangular slot on the left side of the Flush Mount

Pocket or one of the metal retaining brack ets with the wire tie provided in the

kit. Leave approximately 18” of cable extending through the pocket to aid in

the installation and removal of the unit.

Figure 1

Flush Mount Pocket:

Mounts to the bulkhead

and retains the unit

Figure 2

Rubber Pad Location

M4 Machine Nut

Metal Retaining Bracket

Boat Panel

M45x40mm Hex Head

Tool List (Not Included)

Figure 3

Jig Saw Phillips Screwdriver

7mm Wrench Drill and 3/8’ Drill Bit

Masking Tape Thread Locking Compound — (Optional)

Safety Goggles and Dust Mask for drilling

Mounting Pocket

Side View

Wire Tie Slot

CUT ALONG BOLD LINE

TRIM ALONG DASHED LINE

3/8"

DRILL A HO LE FOR

A PLACE T O BEGIN CUT T ING

INSIDE EDGE OF POCKET

Installing/Removing the Unit

1. Connect the wiring harness to the unit, making sure the locking ring is

fully tightened. (Figure 4)

2. Slide the Fishfinder into the pocket. When the Fishfinder is fully inserted,

it will click into place at the lock tabs (Figure 5). It may be necessary to

apply some pressure when inserting the assembly into the pocket to

compress the foam rubber pads.

3. To remove the unit from the pocket, press the lock tabs toward the unit

while sliding the unit out of the pocket. (Figure 6)

Garmin International, Inc.

1200 East 151st Street, Olathe, Kansas 66062, U.S.A

Garmin (Europe) Ltd.

Unit 5, The Quadrangle, Abbey Park In dus tri al Estate, Romsey, SO51 9DL, U.K.

Garmin Corporation

No. 68, Jangshu 2nd Road, Shijr, Taipei County, Taiwan

www.garmin.com

Part Number 190-00311-00 Rev. A

Figure 5 Figure 6

Figure 4

Lock Tabs

Produkt Specifikationer

Mærke:	Garmin
Kategori:	fiskefinder
Model:	Fishfinder 80

Har du brug for hjælp?

Hvis du har brug for hjælp til Garmin Fishfinder 80 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

fiskefinder Garmin Manualer

Garmin Echo 151 Manual

20 September 2024

Garmin 300C Manual

9 August 2024

Garmin FishFinder 400C WW Manual

26 Juli 2024

Garmin ECHOMAP UHD 72cv Manual

25 Juli 2024

Garmin Fishfinder 100 Manual

25 Juli 2024

Garmin Fishfinder 80 Manual

24 Juli 2024

Garmin Fishfinder 240 Manual

23 Juli 2024

Garmin Echo 201 Manual

23 Juli 2024

Garmin STRIKER Vivid 5cv Manual

19 Juli 2024

fiskefinder Manualer

Nyeste fiskefinder Manualer

Humminbird PiranhaMAX 170 Manual

8 Oktober 2024

Lucky FL068-W Manual

19 September 2024

Lucky FF718LIC-WT Manual

15 September 2024

Simrad Cruise 5 Manual

6 September 2024

Closer Pets Fish Mate 5000 GBIO Manual

29 August 2024

Eagle FishMark 320 Portable Manual

25 August 2024

Eagle Cuda 300 Portable Manual

25 August 2024

Humminbird Helix 12 Chirp Mega DI GPS G2N Manual

22 August 2024

Humminbird Helix 12 Chirp GPS G2N Manual

22 August 2024

Humminbird Helix 12 Chirp Mega SI GPS G2N Manual

22 August 2024