Garmin GBT 10 Manual

Garmin Ikke kategoriseret GBT 10

Læs gratis den danske manual til Garmin GBT 10 (6 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 11 personer og har en gennemsnitlig bedømmelse på 4.6 stjerner ud af 6 anmeldelser. Har du et spørgsmål om Garmin GBT 10, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/6
GBT™ 10 Installation and Conguration Instructions
Use the Garmin
®
GBT 10 Bennett Trim Tab Adapter to adapt analog information provided by
a Bennett Trim Tab Position Indicator (Bennett TPI), or by the Bennett trim tab sensors on
your boat, to your NMEA 2000
®
network. Your GBT 10 adapter allows you to observe trim tab
information on the compatible Garmin display devices connected to your NMEA 2000 network.
For a list of compatible Garmin chartplotters and devices, visit www.garmin.com.
Compare the contents of this package with the packing list on the box. If any pieces are
missing, contact your Garmin dealer immediately.
Product Registration
Help us better support you by completing our online registration today. Go to http://my.garmin
.com. Keep the original sales receipt, or a photocopy, in a safe place.
Contact Garmin
Contact Garmin Product Support if you have any questions while using your GBT 10 adapter.
In the USA, go to www.garmin.com/support, or contact Garmin USA by phone at (913)
397.8200 or (800) 800.1020.
In the UK, contact Garmin (Europe) Ltd. by phone at 0808 2380000.
In Europe, go to www.garmin.com/support and click for in-country support Contact Support
information, or contact Garmin (Europe) Ltd. by phone at +44 (0) 870.8501241.
See the Important Safety and Product Information guide in the compatible Garmin display device box for
product warnings and other important information.
Always wear safety goggles, ear protection, and a dust mask when drilling, cutting, or CAUTION:
sanding.
When drilling or cutting, always check the opposite side of the drilling or cutting NOTICE:
surface.
Needed Tools and Supplies
Heat-shrink tubing and a heat gun
Cable ties
Additional NMEA 2000 cabling and connectors (optional)
•
•
•
July 2009 190-01081-04 Rev. A Printed in Taiwan
 GBT10InstallationandCongurationInstructions
Determining an Installation Location
When you are selecting a location to install the GBT 10 adapter, consider the following:
During installation, you connect the GBT 10 adapter to the Bennett TPI (or directly to the
Bennett trim tab sensors), and to the NMEA 2000 network. Therefore:
Choose a location that is within 173 in. (4.4 m) of the Bennett TPI (or the Bennett trim
tab sensors) to avoid splicing bare wires.
Choose a location between the NMEA 2000 backbone and the Bennett TPI (or the
Bennett trim tab sensors).
If you cannot connect the adapter directly to the NMEA 2000 network, add a drop cable.
See for more information.page 3
The adapter is IEC 60529 IPX7 waterproof, and can be submerged up to 30 minutes at 1
meter. Do not install the adapter in a location where it will be submerged regularly, though
the location can be subject to wash-down.
You can use cable ties (not included) to secure the adapter to an existing structure on your
boat.
You can use mounted-head cable ties (not included) and screws (not included) to secure the
adapter to a bulkhead or other suitable surface on your boat.
Install the adapter at least 2 in. (5 cm) from a magnetic compass to prevent electromagnetic
interference, which can cause inaccurate compass readings.
Wiring the GBT 10 Adapter
Connect the GBT 10 adapter either to the Bennett TPI or to the Bennett trim tab sensors directly
using the bare wires on the wiring harness.
Wiring the GBT 10 Adapter to the Bennett
Trim Tab Display
You can wire the GBT 10 adapter directly to the Bennett
TPI. Do not remove any wires from the back of the
Bennett TPI, and wire the GBT 10 adapter to the TPI
according to the following table. Use only the wires listed
for the GBT 10 adapter. Cut and tape any unused wires.
*When wiring the GBT 10 adapter to the Bennett TPI, it is important that you do not connect
wires to the RED and GRN connections farthest from the SHLD connection. Connecting the
GBT 10 adapter wires to the connections farthest from the SHLD connection will interfere with
the operation of the Bennett TPI.
•
◦
◦
◦
•
•
•
•
Bennett TPI
Connector
Label
GBT 10 Adapter
Wire Color
+ None
– None
BRG None
RED None*
RED Blue
SHLD Black
GRN Yellow
GRN None*
Bennett TPI
Connector
Label
GBT 10 Adapter
Wire Color
+ None
– None
BRG None
RED None*
RED Blue
SHLD Black
GRN Yellow
GRN None*

Produkt Specifikationer

Mærke: Garmin
Kategori: Ikke kategoriseret
Model: GBT 10

Har du brug for hjælp?

Hvis du har brug for hjælp til Garmin GBT 10 stil et spørgsmål nedenfor, og andre brugere vil svare dig


Ikke kategoriseret Garmin Manualer

Garmin

Garmin Approach CT1 Manual

26 Februar 2025
Garmin

Garmin Spectra LC302 Manual

9 Januar 2025
Garmin

Garmin Spectra LC102 Manual

9 Januar 2025
Garmin

Garmin dēzl Headset 210 Manual

14 November 2024
Garmin

Garmin Inreach Messenger Plus Manual

11 November 2024
Garmin

Garmin GMM 170 Manual

4 Oktober 2024
Garmin

Garmin GMR 18 xHD Manual

4 Oktober 2024
Garmin

Garmin Edge Power Mount Manual

3 Oktober 2024
Garmin

Garmin GT30-TH Manual

3 Oktober 2024
Garmin

Garmin GMR 18 HD+ Manual

30 September 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

AmpliVox

AmpliVox Airvox SW695 Manual

15 Juni 2025
Stiga

Stiga SBC 635 KD Manual

15 Juni 2025
Cleveland

Cleveland 36CGM300 Manual

15 Juni 2025
Gourmia

Gourmia GTF7970 Manual

15 Juni 2025
Planet Audio

Planet Audio P9630B Manual

15 Juni 2025
ORNO

ORNO OR-DOM-YR-934UD Manual

15 Juni 2025
Lavex

Lavex 842CD12VST12 Manual

15 Juni 2025
Marshall

Marshall RCP-PLUS Manual

15 Juni 2025
Hughes & Kettner

Hughes & Kettner BassForce XL Manual

15 Juni 2025
Hughes & Kettner

Hughes & Kettner Red Box Mk III Manual

15 Juni 2025