Garmin GET 10 Manual

Garmin Ikke kategoriseret GET 10

Læs gratis den danske manual til Garmin GET 10 (8 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 69 personer og har en gennemsnitlig bedømmelse på 4.8 stjerner ud af 35 anmeldelser. Har du et spørgsmål om Garmin GET 10, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/8

GET™ 10 Installation and Conguration Instructions

Use the Garmin

GET 10 adapter to adapt analog information provided by an engine-tilt sensor

on your boat to your NMEA 2000

network. Your GET 10 adapter allows you to observe

engine-tilt information on compatible Garmin display devices connected to your NMEA 2000

network. For a list of compatible Garmin chartplotters and devices, visit www.garmin.com.

Compare the contents of this package with the packing list on the box. If any pieces are

missing, contact your Garmin dealer immediately.

Product Registration

Help us better support you by completing our online registration today. Go to http://my.garmin

.com. Keep the original sales receipt, or a photocopy, in a safe place.

Contact Garmin

Contact Garmin Product Support if you have any questions while using your GET 10. In the

USA, go to www.garmin.com/support, or contact Garmin USA by phone at (913) 397.8200 or

(800) 800.1020.

In the UK, contact Garmin (Europe) Ltd. by phone at 0808 2380000.

In Europe, go to www.garmin.com/support and click for in-country support Contact Support

information, or contact Garmin (Europe) Ltd. by phone at +44 (0) 870.8501241.

See the Important Safety and Product Information guide in the compatible Garmin display device box for

product warnings and other important information..

Always wear safety goggles, ear protection, and a dust mask when drilling, cutting, or CAUTION:

sanding.

When drilling or cutting, always check the opposite side of the drilling or cutting NOTICE:

surface.

Needed Tools and Supplies

Heat-shrink tubing and a heat gun

Cable ties

Additional NMEA 2000 cabling and connectors (optional)

•

July 2009 190-01081-05 Rev. A Printed in Taiwan

 GET10InstallationandCongurationInstructions

Determining an Installation Location

When you are selecting a location to install the GET 10 adapter, consider the following:

During installation, you connect the GET 10 adapter to the analog gauge (or directly to the

engine-tilt sensor), and to the NMEA 2000 network. Therefore:

Choose a location that is within 173 in. (4.4 m) of the analog gauge (or the engine-tilt

sensor) to avoid splicing bare wires.

Choose a location between the NMEA 2000 backbone and the analog gauge (or the

engine-tilt sensor).

If you cannot connect the adapter directly to the NMEA 2000 network, add a drop cable.

See for more information.page 3

The adapter is IEC 60529 IPX7 waterproof, and can be submerged up to 30 minutes at

1 meter. Do not install the adapter in a location where it will be submerged regularly, though

the location can be subject to wash-down.

You can use cable ties (not included) to secure the adapter to an existing structure on your

boat.

You can use mounted-head cable ties (not included) and screws (not included) to secure the

adapter to a bulkhead or other suitable surface on your boat.

Install the adapter at least 2 in. (5 cm) from a magnetic compass to prevent electromagnetic

interference, which can cause inaccurate compass readings.

Wiring the GET 10

Connect the GET 10 adapter either to an analog gauge or to the sender directly using the bare

wires on the wiring harness.

Wiring the GET 10 Adapter to an Analog Gauge

If your boat has an analog gauge representing engine tilt, you can wire the GET 10 adapter

directly to the gauge. Consult the owner’s manual provided by your boat or sensor manufacturer

to determine the ground, sensor, and power (ignition) connections on the gauge. Typically,

the power (ignition) connector is labeled with a “+”, a “+12V”, an “I”, or an “IGN” marking.

The ground connector is typically labeled with a “-”, a “ ”, or a “G” marking, and the sensor

connector is typically labeled with an “S” or a “G” marking. Do not remove any wires from the

back of the gauge, and wire the GET 10 adapter to the gauge using the following table.

Wiring the GET 10 Adapter Directly to an Engine-Tilt Sensor

If your boat does not have an analog gauge representing engine tilt, you can wire the adapter

directly to the sensor. All outboard and inboard/outboard motors that feature trim control should

have either a terminal or a wire allowing access to the engine-tilt sensor. Consult the owner’s

manual provided by your boat or sensor manufacturer to determine the type of sensor (resistive

or generic voltage) in use, and the sending and ground terminals on the sensor. Typically, the

sending terminal is labeled with an “S” marking for sensor or a “G” marking for gauge, and the

ground terminal is typically labeled with a negative sign (-). Wire the GET 10 adapter to the

sensor according to the following table.

•

◦

•

Produkt Specifikationer

Mærke:	Garmin
Kategori:	Ikke kategoriseret
Model:	GET 10

Har du brug for hjælp?

Hvis du har brug for hjælp til Garmin GET 10 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Garmin Manualer

Garmin Foretrex 701 Ballistic Edition Manual

12 August 2025

Garmin Approach CT1 Manual

26 Februar 2025

Garmin dēzl Headset 110 Manual

8 Februar 2025

Garmin Spectra LC302 Manual

9 Januar 2025

Garmin Spectra LC102 Manual

9 Januar 2025

Garmin dēzl Headset 210 Manual

14 November 2024

Garmin Inreach Messenger Plus Manual

11 November 2024

Garmin GMM 170 Manual

4 Oktober 2024

Garmin GMR 18 xHD Manual

4 Oktober 2024

Garmin Edge Power Mount Manual

3 Oktober 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Atlas AT100-PA Manual

1 September 2025

Furman PL-Pro DMC E Manual

1 September 2025

Omnires Y1236/K MAX Manual

1 September 2025

Gree IDAV 1021A Manual

1 September 2025

Gree IDAV 1321A Manual

1 September 2025

RYOBI RRT12 Manual

1 September 2025

Gree ERAF 0821A Manual

1 September 2025

Wëasy kfx32 Manual

1 September 2025

Wëasy crust70 Manual

1 September 2025

Biltema 27-0171 Manual

1 September 2025