Garmin GHS 11i Manual


Læs gratis den danske manual til Garmin GHS 11i (14 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 41 personer og har en gennemsnitlig bedømmelse på 4.6 stjerner ud af 21 anmeldelser. Har du et spørgsmål om Garmin GHS 11i, eller vil du spørge andre brugere om produktet?

Side 1/14
GHS™ 11
Installation Instructions 2
Instructions d'installation 3
Istruzioni di installazione 4
Installationsanweisungen 5
Instrucciones de instalación 7
Instruções de instalação 8
Installatie-instructies 9
Asennusohjeet 10
Installeringsinstruksjoner 11
Installationsinstruktioner 12
Instrukcja instalacji 13
Garmin® and the Garmin logo are trademarks of Garmin Ltd. or its subsidiaries, registered in the USA and other countries. GHS
is a trademark of Garmin Ltd. or its subsidiaries. These trademarks may not be
used without the express permission of Garmin.
July 2017
190-02061-97_0A
GHS™ 11
Installation Instructions
Important Safety Information
WARNING
See the guide in the Important Safety and Product Information
product box for product warnings and other important
information.
CAUTION
Always wear safety goggles, ear protection, and a dust mask
when drilling, cutting, or sanding.
NOTICE
When drilling or cutting, always check what is on the opposite
side of the surface.
Tools Needed
• Pencil
• Drill
22 mm (7/8 in.) drill bit or hole saw
3 mm (1/8 in.) drill bit
4.76 mm (3/16 in.) wrench
Phillips screwdriver
Marine sealant (optional)
Mounting Considerations
NOTICE
This device should be mounted in a location that is not exposed
to extreme temperatures or conditions. The temperature range
for this device is listed in the product specifications. Extended
exposure to temperatures exceeding the specified temperature
range, in storage or operating conditions, may cause device
failure. Extreme-temperature-induced damage and related
consequences are not covered by the warranty.
When selecting a mounting location, observe these
considerations.
To avoid interference with a magnetic compass, do not install
the device closer to a compass than the compass-safe
distance value listed in the product specifications.
A 10 m (32 ft) extension cable is included to connect the
handset to the VHF radio. You must select a mounting
location for the handset that allows this extension cable to
connect to the back of the VHF radio.
You can use the included screws to mount the extension
cable and the handset cradle mount on your boat. If the
included screws are not appropriate for the mounting surface,
you must purchase suitable hardware.
Installing the Extension Cable in the Mounting
Surface
Before drilling a hole to mount the extension cable, you must
make sure that the extension cable is long enough connect to
the back of the VHF radio from the selected mounting location.
1Using the mounting plate À as a template, trace the cable
hole in the center of the mounting plate and mark the screw
locations.
2Set the mounting plate aside.
Do not drill through the mounting plate.
3Using a 22 mm (7/8 in.) drill bit or hole saw, drill the center
cable hole Á in the mounting surface.
4Using a 3 mm (1/8 in.) drill bit, drill the pilot holes.
5Apply marine sealant between the mounting plate and the
mounting surface to help seal the holes (optional).
6Using the included screws, attach the mounting plate to the
mounting surface.
7Connect one end of the extension cable to the microphone
relocation port on the back of the VHF radio, and route the
other end of the extension cable to the mounting location.
8Feed the extension cable connector
 through the back of
the mounting surface.
9Apply marine sealant around the extension cable connector
in the mounting plate to help seal the hole (optional).
10Secure the extension cable connector to the mounting plate
using the weather cap à and the nut Ä.
11Connect the handset to the extension cable.
Installing the Cradle Mount
1Select a mounting location near the extension cable.
TIP: You can place the handset in the cradle mount, connect
the handset to the extension cable, and hold it against the
mounting surface to help determine the best location.
2Using the cradle mount as a template, mark the screw
locations.
3Set the cradle mount aside.
Do not drill through the cradle mount.
4Using a 3 mm (1/8 in.) drill bit, drill the pilot holes.
5Using the included screws, secure the cradle mount to the
mounting surface.
Specifications
Specification Measurement
Dimensions (H×W×D) 154 × 69 × 40 mm (6.1 × 2.7 × 1.6 in.)
Weight 318 g (11.22 oz.)
Temperature range Operating: From -15° to 70°C (from 5° to
158°F)
Storage: From -20° to 70°C (from -4° to
158°F)
Compass-safe distance 60 cm (23.6 in.)
Water rating IEC 60529 IPX7*
*The device withstands incidental exposure to water of up to 1 m
for up to 30 min. For more information, go to www.garmin.com
/waterrating.
2 Installation Instructions


Produkt Specifikationer

Mærke: Garmin
Kategori: Ikke kategoriseret
Model: GHS 11i

Har du brug for hjælp?

Hvis du har brug for hjælp til Garmin GHS 11i stil et spørgsmål nedenfor, og andre brugere vil svare dig




Ikke kategoriseret Garmin Manualer

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer