Garmin GRF 10 Manual


Læs gratis den danske manual til Garmin GRF 10 (26 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 25 personer og har en gennemsnitlig bedømmelse på 4.4 stjerner ud af 13 anmeldelser. Har du et spørgsmål om Garmin GRF 10, eller vil du spørge andre brugere om produktet?

Side 1/26
GRF 10 Installation Instructions .................................................................................................... 2
Instructions d'installation du GRF 10 ............................................................................................. 4
GRF 10 - Istruzioni di installazione ................................................................................................6
GRF 10 – Installationsanweisungen ..............................................................................................8
Instrucciones de instalación del GRF 10 ..................................................................................... 10
GRF 10 – Instruções de Instalação ............................................................................................. 12
GRF 10 - Installatie-instructies .................................................................................................... 14
GRF 10 Installationsvejledning ....................................................................................................16
GRF 10:n asennusohjeet ............................................................................................................ 18
Installeringsinstruksjoner for GRF 10 .......................................................................................... 20
GRF 10-installationsinstruktioner ................................................................................................ 22
GRF 10 — instrukcja instalacji .................................................................................................... 23
Garmin International, Inc.
1200 East 151st Street
Olathe, Kansas 66062, USA
Garmin (Europe) Ltd.
Liberty House, Hounsdown Business Park
Southampton, Hampshire, SO40 9LR UK
Garmin Corporation
No. 68, Zhangshu 2nd Road, Xizhi Dist.
New Taipei City, 221, Taiwan (R.O.C.)
Garmin® and the Garmin logo are trademarks of Garmin Ltd. or its subsidiaries, registered in the USA and other countries. These
trademarks may not be used without the express permission of Garmin.
September 2012 190-01454-94_0B Printed in Taiwan
GRF 10 Installation Instructions
WARNING
See the guide in the Important Safety and Product Information
product box for product warnings and other important
information.
Installation Preparation
CAUTION
Always wear safety goggles, ear protection, and a dust mask
when drilling, cutting, or sanding.
NOTICE
When drilling or cutting, always check what is on the opposite
side of the surface.
Package Contents
Item Description
ÀGRF 10
ÁM4 screw (×5)
ÂM6 locknut (×2)
ÃM6 nut (×2)
ÄWasher
ÅTiller arm mount
ÆBall joint assembly (×2)
ÇThreaded rod
Tools Needed
Drill and 1/8 in. (3.2 mm) drill bit
8 and 10 mm wrenches
10 mm socket
Metal saw appropriate for cutting a threaded rod
#2 Phillips screwdriver
Tape measure
Pencil or marker
Extension cables, if necessary ( )page 2
Mounting Considerations
ÀThe sensor must be installed parallel to the tiller arm while the
rudder is amidships.
ÁThe distance from the rotation axis of the tiller to the ball-joint
assembly must be the same as the distance from the rotation axis
of the sensor to the ball joint assembly.
ÂThe sensor and rudder rotation axes must be aligned.
ÃThe maximum range of travel from stop to stop is 140° (70º from
the center position to each stop). Exceeding this range may result
in damage to the sensor.
ÄThe rod that connects the sensor to the tiller arm is 11.8 in. (300
mm) long, and can be shortened if needed.
The rod should be level when connected to the sensor and rudder.
If a perfectly level installation is not possible, the rod must be
installed within +/- 5º off level in order to function correctly.
ÅThe rod should be installed perpendicular to the tiller arm and
sensor, using the second hole from the tip of the sensor for the ball-
joint connector.
Although the second hole is preferred, the other holes may be used
if necessary for the installation location.
Connection Considerations
This sensor can be connected to a compatible Garmin
®
autopilot system with a 12-pin rudder feedback connector.
The cable connected to the sensor is 78 in. (2 m) long.
If needed, extension cables for the sensor are available
from your Garmin dealer.
Do not cut the sensor cable to extend or shorten it.
Installation Procedures
Installing the Sensor
For the best results, keep the rudder amidships during the
sensor-installation process.
1Rotate the sensor counter-clockwise so the arrows on the
back À line up in the center Á before marking the mounting
holes.
2


Produkt Specifikationer

Mærke: Garmin
Kategori: Ikke kategoriseret
Model: GRF 10

Har du brug for hjælp?

Hvis du har brug for hjælp til Garmin GRF 10 stil et spørgsmål nedenfor, og andre brugere vil svare dig




Ikke kategoriseret Garmin Manualer

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer