Garmin GT51M-THP Manual

Garmin Ikke kategoriseret GT51M-THP

Læs gratis den danske manual til Garmin GT51M-THP (8 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 35 personer og har en gennemsnitlig bedømmelse på 4.9 stjerner ud af 18 anmeldelser. Har du et spørgsmål om Garmin GT51M-THP, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/8
Thru-Hull Transducer
Installation Instructions
Important Safety Information
WARNING
See the guide in the Important Safety and Product Information
product box for product warnings and other important
information.
The device must be installed with at least one of the included
anti-rotation bolts. Failure to do so could result in the device
rotating while the boat is moving and could cause damage to
your vessel.
You are responsible for the safe and prudent operation of your
vessel. Sonar is a tool that enhances your awareness of the
water beneath your boat. It does not relieve you of the
responsibility of observing the water around your boat as you
navigate.
CAUTION
Failure to install and maintain this equipment in accordance with
these instructions could result in damage or injury.
Always wear safety goggles, ear protection, and a dust mask
when drilling, cutting, or sanding.
NOTICE
When drilling or cutting, always check what is on the opposite
side of the surface.
This equipment should be installed by a qualified marine
installer.
To obtain the best performance and to avoid damage to your
boat, you must install the Garmin® transducer according to these
instructions.
Read all installation instructions before proceeding with the
installation. If you experience difficulty during the installation,
contact Garmin Product Support.
Registering Your Device
Help us better support you by completing our online registration
today.
• Go to .http://my.garmin.com
• Keep the original sales receipt, or a photocopy, in a safe
place.
Contacting Garmin Product Support
• Go to for in-country support www.garmin.com/support
information.
• In the USA, call 913-397-8200 or 1-800-800-1020.
• In the UK, call 0808 238 0000.
• In Europe, call +44 (0) 870 850 1241.
Loading the New Software on a Memory Card
You must copy the software update to a memory card.
1Insert a memory card into the card slot on the computer.
2Go to .www.garmin.com/support/software/marine.html
3Select next to “Garmin Marine Network with SD Download
card”.
4Read and agree to the terms.
5Select .Download
6If necessary, select or save and open the file.Run
7If necessary, select the drive associated with the memory
card, and select > .Next Finish
Updating the Device Software
Before you can update the software, you must obtain a
software-update memory card or load the latest software onto a
memory card.
1Turn on the chartplotter.
2After the home screen appears, insert the memory card into
the card slot.
NOTE: In order for the software update instructions to
appear, the device must be fully booted before the card is
inserted.
3Follow the on-screen instructions.
4Wait several minutes while the software update process
completes.
The device returns to normal operation after the software
update process is complete.
5Remove the memory card.
NOTE: If the memory card is removed before the device
restarts fully, the software update is not complete.
Tools Needed
• Drill
• 3 mm bit (1/8 in.)
• 9 mm bit (3/8 in.)
• 13 mm bit (1/2 in.)
• 25 mm spade bit (1 in.) (fiberglass hull)
• 29 mm spade bit (1 1/8 in.) (fiberglass hull)
• 32 mm spade bit (11/4 in.) (fiberglass hull)
• 32 mm hole saw (1 1/4
in.) (metal hull)
• Bandsaw or table saw
• Slip-joint pliers or crescent wrench
• Masking tape
• Marine sealant
• Epoxy or exposed core sealant (cored fiberglass hull)
About the Transducer
The transducer transmits and receives sound waves through the
water, and relays sound-wave information to your Garmin sonar
device.
Mounting Location Considerations
• On outboard and sterndrive vessels
À, the transducer should
be mounted in front of and close to the engine or engines.
• On inboard vessels Á, the transducer should be mounted in
front of and far away from the engine propeller and shaft.
• On step-hull vessels Â, the transducer should be mounted in
front of the first step.
May 2015 Printed in Taiwan 190-01774-02_0B
• On full-keel vessels Ã, the transducer should be mounted at
a slight angle that aims at the bow, not parallel to the
centerline.
• On fin-keel vessels Ä, the transducer should be mounted
from 25 cm to 75 cm (from 10 to 30 in.) in front of the keel
and a maximum of 10 cm (4 in.) to the side of the centerline.
• On vessels with displacement hulls Å, the transducer should
be mounted approximately 1/3 aft of the waterline length of
the vessel from the bow, and from 150 to 300 mm (from 6 to
12 in.) to the side of the centerline.
• The transducer should be mounted parallel to the bow-stern
axis of your vessel.
• The transducer should not be mounted behind strakes, struts,
fittings, water intake or discharge ports, or anything that
creates air bubbles or causes the water to become turbulent.
The transducer must be in clean (non-turbulent) water for
optimal performance.
• The transducer should not be mounted in a location where it
might be jarred when launching, hauling, or storing.
• On single-drive boats, the transducer must not be mounted in
the path of the propeller.
The transducer can cause cavitation that can degrade the
performance of the boat and damage the propeller.
• On twin-drive boats, the transducer should be mounted
between the drives, if possible.
Fairing Block Angle Cut
A fairing block positions your transducer parallel to the water line
for increased sonar accuracy. You must measure the deadrise
angle of your boat hull to determine if a fairing block is
necessary to mount the transducer. If the deadrise angle of your
mounting location exceeds 5°, you should use a fairing block to
mount the transducer.
Deadrise Angle
Deadrise is the angle formed between a horizontal line and a
boat hull at a single point. You can measure the deadrise angle
with an angle finder, a protractor, or a digital level. You can also
ask your boat manufacturer for the deadrise angle of the specific
point on your boat hull.
NOTE: A boat may have several deadrise angles depending on
the shape of the hull. Measure the deadrise angle only at the
location where you plan to install the transducer.
Cutting the Fairing Block
CAUTION
Always wear safety goggles, ear protection, and a dust mask
when drilling, cutting, or sanding.
1Using wood screws, attach the fairing block to a piece of
wood.
The wood becomes a cutting guide for the fairing block.
2Measure the deadrise angle of the hull at the mounting
location.
3Tilt your table saw blade À to match the deadrise angle and
secure the cutting fence.
4Position the fairing block on the table so the cutting guide
rests against the fence Á and the angle matches the angle of
the mounting location .
5Adjust the cutting fence to ensure the fairing block has a
minimum thickness of 13 mm (1/2 in.).
NOTE: The maximum cutting angle of the fairing block is 25°.
6Cut the fairing block.
7Using a rasp or power tool, shape the fairing block to the hull
as precisely as possible.
8Use the remaining section of the fairing block as the backing
block inside the hull.
Cored Fiberglass Boat Hull Installation
Instructions
Thru-Hull Transducer in a Cored Hull with a Fairing
Block
If the deadrise angle of your mounting location exceeds 5°, you
must use a fairing block to mount the device.
Drilling the Transducer Stem Hole and the Anti-Rotation
Bolt Holes in a Cored Fiberglass Hull
Before you can drill holes for the anti-rotation bolts, you must
drill the hole for the transducer stem (Drilling the Transducer
Stem Hole and the Anti-Rotation Bolt Holes in a Cored
Fiberglass Hull Cutting the ) and you must cut the fairing block (
Fairing Block).
WARNING
The device must be installed with at least one of the included
anti-rotation bolts. Failure to do so could result in the device
rotating while the boat is moving and could cause damage to
your vessel.
The core must be cut and sealed carefully to protect against
water seepage.
1Select a mounting location without surface irregularities or
obstructions.
2Using the template, mark the location of the stem hole and
anti-rotation bolts.
3Drill a 3 mm (1/8 in.) pilot hole through the template and hull
at the stem hole location.
The hole must be perpendicular to the water surface.
4Place masking tape over the pilot hole and surrounding area
outside the hull to prevent damage to the fiberglass.
5Using a 25 mm (1 in.) bit at the stem hole location, drill from
outside the hull through the outer skin
À, inner skin Á, and
the core Â.
2

Produkt Specifikationer

Mærke: Garmin
Kategori: Ikke kategoriseret
Model: GT51M-THP

Har du brug for hjælp?

Hvis du har brug for hjælp til Garmin GT51M-THP stil et spørgsmål nedenfor, og andre brugere vil svare dig


Ikke kategoriseret Garmin Manualer

Garmin

Garmin Foretrex 701 Ballistic Edition Manual

12 August 2025
Garmin

Garmin Approach CT1 Manual

26 Februar 2025
Garmin

Garmin dēzl Headset 110 Manual

8 Februar 2025
Garmin

Garmin Spectra LC302 Manual

9 Januar 2025
Garmin

Garmin Spectra LC102 Manual

9 Januar 2025
Garmin

Garmin dēzl Headset 210 Manual

14 November 2024
Garmin

Garmin Inreach Messenger Plus Manual

11 November 2024
Garmin

Garmin GMM 170 Manual

4 Oktober 2024
Garmin

Garmin GMR 18 xHD Manual

4 Oktober 2024
Garmin

Garmin Edge Power Mount Manual

3 Oktober 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Atlas

Atlas AT100-PA Manual

1 September 2025
Furman

Furman PL-Pro DMC E Manual

1 September 2025
Omnires

Omnires Y1236/K MAX Manual

1 September 2025
Gree

Gree IDAV 1021A Manual

1 September 2025
Gree

Gree IDAV 1321A Manual

1 September 2025
RYOBI

RYOBI RRT12 Manual

1 September 2025
Gree

Gree ERAF 0821A Manual

1 September 2025
Wëasy

Wëasy kfx32 Manual

1 September 2025
Wëasy

Wëasy crust70 Manual

1 September 2025
Biltema

Biltema 27-0171 Manual

1 September 2025