GBC HeatSeal H600 Pro Manual

GBC Lamineringssystem HeatSeal H600 Pro

Læs gratis den danske manual til GBC HeatSeal H600 Pro (8 sider) i kategorien Lamineringssystem. Denne vejledning er vurderet som hjælpsom af 16 personer og har en gennemsnitlig bedømmelse på 3.8 stjerner ud af 8.5 anmeldelser. Har du et spørgsmål om GBC HeatSeal H600 Pro, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/8
General Binding Corporation
Northbrook, IL 60062-4195
®
®
13 PRO Operating Instructions. . . . . . . . . . 2
Manuel d’Utilisation . . . . . . . . . . . . 3
Manual de Utilización . . . . . . . . . . 5
Operating Instructions
IMPORTANT SAFETY INSTRUCTIONS
YOUR SAFETY AS WELL AS THE SAFETY
OF OTHERS IS IMPORTANT TO US. IN THIS
INSTRUCTION MANUAL AND ON THE
PRODUCT ARE IMPORTANT SAFETY
MESSAGES. READ THESE MESSAGES
CAREFULLY.
THE SAFETY ALERT SYMBOL PRE-
CEDES EACH SAFETY MESSAGE IN
THIS INSTRUCTION MANUAL.THIS SYMBOL
INDICATES A POTENTIAL PERSONAL SAFE-
TY HAZARD THAT COULD HURT YOU OR
OTHERS, AS WELL AS CAUSE PRODUCT
DAMAGE OR PROPERTY DAMAGE.
THE FOLLOWING WARNING IS FOUND ON
THE BOTTOM OF THE PRODUCT.
This safety message means that you could
be seriously hurt or killed if you open the
product and expose yourself to hazardous
voltage.
IMPORTANT SAFEGUARDS
WARNING: FOR YOUR PROTECTION
DO NOT CONNECT THE POUCH
LAMINATOR TO ELECTRICAL POWER
UNTIL YOU READ THESE INSTRUCTIONS
COMPLETELY. KEEP THESE INSTRUCTIONS
IN A CONVENIENT LOCATION FOR FUTURE
REFERENCE. TO GUARD AGAINST INJURY,
THE FOLLOWING BASIC SAFETY PRECAU-
TIONS MUST BE OBSERVED IN THE SET-UP
AND USE OF THIS PRODUCT.
GENERAL SAFEGUARDS
•Use the pouch laminator only for its
intended purpose of laminating
documents according to the indicated
specifications.
•Do not place anything in the throat
opening of the machine other than
carriers with pouches/documents.
•Place unit on a secure, stable work area
to prevent the machine falling and
possibly causing personal injury and
damage to the unit.
•Turn unit off when not in use for an
extended period of time.
•Follow all warnings and instructions
marked on the product.
ELECTRICAL SAFEGUARDS
•The pouch laminator must be connected
to a supply voltage corresponding to the
electrical rating of the machine as
indicated.
•Unplug the pouch laminator before
moving it, or when it is not in use for an
extended period of time.
•Do not operate with a damaged supply
cord or plug, after it malfunctions, or after
it has been damaged in any manner.
•Do not overload electrical outlets beyond
their capacity as this can result in fire or
electrical shock.
•Do not alter attachment plug. Plug is
configured for the appropriate electrical
supply.
•The unit is intended for indoor use only.
•Never push objects into this product
through cabinet slots. Do not spill liquid of
any kind on this product.
SERVICE
•Do not attempt to service or repair the
pouch laminator yourself. Unplug the unit
and contact an authorized service
representative for any required repairs.
CLEANING
CAUTION: Unplug this product before
cleaning.
•Wipe exterior only with a damp cloth. Do
not use detergents or solvents.
OPERATION
Control Panel LCD. The following
information is displayed on the LCD:
READY - Indicates that the machine is at the
requested laminating temperature.
TEMPERATURE - The numbers directly
below the word TEMPERATURE indicate the
user requested temperature setting.
SPEED - The numbers directly below the
word SPEED indicate the speed setting.
Selecting Functions. Pressing keys
performs functions as follows:
Low - Sets the machine to 230°F (110°C),
speed 5
Mid - Sets the machine to 266°F (130°C),
speed 3.
High - Sets the machine to 302°F (150°C)
speed 3.
Note: Use of a carrier is recommended with
all films for better quality output and
protection of rollers.
PRE/H - Sets the machine to 176˚ ˚ F (80 C),
Speed 2, stand-by.
MEAS - Measures the current machine
temperature.
COLD - This is the setting that is
automatically selected when the machine is
first turned on. Sets the machine to 0, no
temperature and no speed. If the
temperature of the heater platen is above 90˚
C (194 F), then speed ˚ “2” is automatically
set to protect the rollers.
TEMPERATURE -These keys are used to
increase or decrease temperature by
1˚F. Temperature can be adjusted up
to 160 C or 320˚ ˚ F.
SPEED - Adjust the speed of the rollers.
Speed 6 is the fastest speed.
STOP - Stops the revolution of the rollers. To
protect the rollers, the machine should not be
stopped for long periods of time when the
temperature is above 90 C (194˚ ˚ F).
REV - Reverses the revolution of the
rollers to correct misfeeds.
SET-UP
1. Connect power cord to appropriate power
source.
2. Push the power switch located on the back
of the machine to the “on” position.
HOT LAMINATION
After the laminator has been turned on using
the power switch located on the back of the
machine, the Cold mode is automatically set.
“Ready,” temperature setting “0” and speed
setting “ ”0 should be displayed on the LCD.
1. Select either “LOW, MID, or HIGH”
function key. The LCD will indicate the
temperature and speed selected. “Ready”
will not be indicated until the laminator
has reached the set temperature.
2. Use the Laminating Guide included with
the machine to select the proper tempera-
ture and speed for the material to be
laminated.
3. Center the item to be laminated into a
laminating pouch, so that the borders are
even on all sides.
4. Insert the pouch with the item sealed-edge
first into the paper CARRIER that is includ-
ed with each carton of pouches. Position
the sealed edge of the pouch against the
inside folded edge of the carrier.
5. Insert the carrier and its contents straight
into the machine, leading with the folded
edge. handle carriers carefully so that
they can be reused.
WARNING
Electrical shock hazard. Do not
open. No user servicable parts
inside. Refer servicing to
qualified service personnel.
2
13 Pro
!
REV
Selecting
Functions
}
}
Control
Panel
LCD

Produkt Specifikationer

Mærke: GBC
Kategori: Lamineringssystem
Model: HeatSeal H600 Pro

Har du brug for hjælp?

Hvis du har brug for hjælp til GBC HeatSeal H600 Pro stil et spørgsmål nedenfor, og andre brugere vil svare dig


Lamineringssystem GBC Manualer

GBC

GBC Catena 65 Manual

4 Januar 2025
GBC

GBC Swingline Fusion 5000L Manual

7 Oktober 2024
GBC

GBC HeatSeal H600 Pro Manual

25 August 2024
GBC

GBC Ultima 35 EZ Load Manual

25 August 2024
GBC

GBC Pro Series 3600 Manual

6 August 2024
GBC

GBC Foton 30 Manual

5 August 2024
GBC

GBC 1701920 Manual

28 Juli 2024
GBC

GBC 4400306EU Manual

24 Juli 2024
GBC

GBC HeatSeal ProSeries 3500LM Manual

8 Juli 2024
GBC

GBC 3500LM Manual

8 Juli 2024

Lamineringssystem Manualer

Nyeste Lamineringssystem Manualer

Exibel

Exibel L402-A Manual

2 Marts 2025
SEAL

SEAL 54 EL Manual

9 Februar 2025
Fellowes

Fellowes Saturn 2 A3/125 Manual

12 Januar 2025
SEAL

SEAL 65ProMD Manual

4 Januar 2025
Fellowes

Fellowes SPL A2 Manual

30 September 2024
Fellowes

Fellowes Halo A3/125 Manual

26 September 2024
Fellowes

Fellowes SPL A3 Manual

4 September 2024
Fellowes

Fellowes Venus2 125 Manual

2 September 2024
United Office

United Office ULG 350 A1 Manual

1 September 2024
Pavo

Pavo AlaskaVigo A3 Manual

29 August 2024