GE GTS18GCSWW Manual
Læs nedenfor 📖 manual på dansk for GE GTS18GCSWW (24 sider) i kategorien Køleskab. Denne guide var nyttig for 17 personer og blev bedømt med 4.7 stjerner i gennemsnit af 9 brugere
Side 1/24
ge.com
Refrigerators
Top-Freezer
197D7799P001 49-60521-1 08-08 JR
Safety Instructions . . . . . . . . . .2–4
Operating Instructions
Automatic Icemaker . . . . . . . . . . . .7
Care and Cleaning . . . . . . . . . . . . .8
Shelves . . . . . . . . . . . . . . . . . . . . .5, 6
Storage Drawers . . . . . . . . . . . . . . .6
Temperature Controls . . . . . . . . . .5
Installation Instructions
Preparing to Install
the Refrigerator . . . . . . . . . . . . . . .9
Reversing the Door Swing . . .13–16
Water Line Installation . . . . . .10–12
Troubleshooting Tips
Before You Call For Service . . 17, 18
Normal Operating Sounds . . . . . .17
Consumer Support
Consumer Support . . . . Back Cover
Product Registration
(Canadian) . . . . . . . . . . . . . . . 21, 22
Product Registration (U.S.) . 20–22
Warranty for
Canadian Customers . . . . . . . . . . 19
Warranty for U.S. Customers . . . 23
Write the model and serial
numbers here:
Model #______________________
Serial # ______________________
You can find them on a label on
the upper left side of the fresh food
compartment.
Models 16, 17, 18
Owner’s Manual and
Installation Instructions
2
COMMENT VOUS DÉBARRASSER
CONVENABLEMENT DE VOTRE ANCIEN RÉFRIGÉRATEUR
Les enfants pris au piège ou morts d’asphyxie
sont toujours d’actualité. Les réfrigérateurs
abandonnés sont toujours aussi dangereux,
même si on n’attend que «quelques jours»
pour s’en débarrasser. Si vous ne gardez pas
votre ancien réfrigérateur, veuillez suivre les
directives ci-dessous afin de prévenir les accidents.
Avant de vous débarrasser de votre ancien
réfrigérateur ou congélateur :
■Démontez les portes.
■Laissez les clayettes en place afin d’empêcher
les enfants de grimper à l’intérieur.
Réfrigérants
Tous les appareils de réfrigération contiennent
des réfrigérants qui, conformément aux lois
fédérales, doivent être enlevés avant toute
élimination de l’appareil. Si vous vous
débarrassez de vieux appareils de réfrigération,
vérifiez, auprès de la société qui s’occupe de
leur élimination, ce que vous devez faire.
DANGER! RISQUES POUR LES ENFANTS
PROPER DISPOSAL OF THE REFRIGERATOR
Child entrapment and suffocation are not
problems of the past. Junked or abandoned
refrigerators are still dangerous…even if they
will sit for “just a few days.” If you are getting
rid of your old refrigerator, please follow the
instructions below to help prevent accidents.
Before You Throw Away Your Old
Refrigerator or Freezer:
■Take off the doors.
■Leave the shelves in place so that children
may not easily climb inside.
Refrigerants
All refrigeration products contain refrigerants,
which under federal law must be removed prior
to product disposal. If you are getting rid of an
old refrigeration product, check with the
company handling the disposal about what
to do.
DANGER! RISK OF CHILD ENTRAPMENT
Consumer Support Troubleshooting Tips Operating InstructionsInstallation InstructionsTroubleshooting Tips Installation Instructions Operating InstructionsTroubleshooting Tips Installation Instructions Safety InstructionsOperating Instructions
CORDONS PROLONGATEURS
Nous vous recommandons fortement de ne pas utiliser de cordons prolongateurs à cause des risques
potentiels qu’ils présentent dans certaines conditions.
Toutefois si vous décidez d’utiliser tout de même un cordon prolongateur, il est absolument nécessaire
qu’il s’agisse d’un cordon à 3 fils avec mise à la terre pour appareils électroménagers homologué UL (aux
États-Unis) ou certifié CSA (au Canada), pourvu d’une fiche et d’une prise mises à la terre de 15 ampères
(minimum) et de 120 volts.
USE OF EXTENSION CORDS
Because of potential safety hazards under certain conditions, we strongly recommend
against the use of an extension cord.
However, if you must use an extension cord, it is absolutely necessary that it be a UL-listed (in the United
States) or a CSA certified (in Canada), 3-wire grounding type appliance extension cord having a grounding
type plug and outlet and that the electrical rating of the cord be 15 amperes (minimum) and 120 volts.
IMPORTANT SAFETY INFORMATION.
READ ALL INSTRUCTIONS BEFORE USING.
Consumer SupportTroubleshooting TipsOperating InstructionsSafety Instructions Installation Instructions
IMPORTANT SAFETY INFORMATION.
READ ALL INSTRUCTIONS BEFORE USING. ge.com
WARNING!
Use this appliance only for its intended purpose as described in this Owner’s Manual.
SAFETY PRECAUTIONS
When using electrical appliances, basic safety precautions should be followed, including the following:
■
■This refrigerator must be properly installed
and located in accordance with the Installation
Instructions before it is used.
■
■Do not allow children to climb, stand or hang
on the shelves in the refrigerator. They could
damage the refrigerator and seriously injure
themselves.
■
■Do not touch the cold surfaces in the freezer
compartment when hands are damp or wet.
Skin may stick to these extremely cold surfaces.
■
■Do not store or use gasoline or other flammable
vapors and liquids in the vicinity of this or any
other appliance.
■
■Keep fingers out of the “pinch point” areas;
clearances between the doors and between
the doors and cabinet are necessarily small.
Be careful closing doors when children are
in the area.
■
■In refrigerators with automatic icemakers,
avoid contact with the moving parts of the
ejector mechanism, or with the heating element
that releases the cubes. Do not place fingers or
hands on the automatic icemaking mechanism
while the refrigerator is plugged in.
■
■Unplug the refrigerator before cleaning and
making repairs.
NOTE: We strongly recommend that any servicing be
performed by a qualified individual.
■
■Turning the control to the
0
position does
not remove power to the light circuit.
■
■Do not refreeze frozen foods which have
thawed completely.
MESURES DE SÉCURITÉ IMPORTANTES.
LISEZ D’ABORD TOUTES LES DIRECTIVES.
AVERTISSEMENT!
N’utilisez cet électroménager que pour l’usage auquel il est destiné, comme expliqué dans le
présent manuel.
MESURES DE SÉCURITÉ
Lorsque vous utilisez un appareil électrique, observez toujours les mesures de sécurité de base,
y compris les suivantes.
■Installez le réfrigérateur conformément aux
directives d’installation avant de l’utiliser.
■Ne laissez pas les enfants grimper, s’asseoir,
se tenir debout ni se pendre aux clayettes du
réfrigérateur. Ils pourraient endommager le
réfrigérateur et se blesser gravement.
■N’entreposez et n’utilisez pas d’essence ou
autres vapeurs et liquides inflammables à
proximité de cet appareil ou de tout autre
appareil électroménager.
■Éloignez les doigts des parties du réfrigérateur
où l’on peut facilement se pincer : les espaces
entre les portes et entre les portes et les placards
sont toujours étroits. Soyez prudent lorsque
vous fermez les portes de l’appareil en présence
des enfants.
■Si votre réfrigérateur est doté d’une machine à
glaçons automatique évitez le contact avec les
pièces mobiles du mécanisme éjecteur, ou avec
l’élément chauffant qui libère les glaçons.
Ne posez pas les doigts ou les mains sur le
mécanisme de la machine à glaçons pendant
que le réfrigérateur est branché.
■Ne touchez pas les surfaces froides du congélateur
si vous avez les mains humides ou mouillées : la
peau risque d’adhérer à ces surfaces très froides.
■Débranchez votre réfrigérateur avant de le
nettoyer ou de le réparer.
REMARQUE : Nous vous recommandons vivement de
confier toute réparation à un technicien qualifié.
■Lorsque vous réglez la commande sur
0
(éteint),
l’alimentation électrique de l’ampoule n’est pas
coupée.
■Ne recongelez pas les aliments surgelés qui ont
complètement dégelé. 3
IMPORTANT SAFETY INFORMATION.
READ ALL INSTRUCTIONS BEFORE USING.
WARNING!
HOW TO CONNECT ELECTRICITY
Do not, under any circumstances, cut or remove the third (ground) prong from the power cord.
For personal safety, this appliance must be properly grounded.
The power cord of this appliance is equipped with a 3-
prong (grounding) plug which mates with a standard
3-prong (grounding) wall outlet to minimize the
possibility of electric shock hazard from this appliance.
Have the wall outlet and circuit checked by a qualified
electrician to make sure the outlet is properly
grounded.
Where a standard 2-prong wall outlet is encountered, it
is your personal responsibility and obligation to have it
replaced with a properly grounded 3-prong wall outlet.
The refrigerator should always be plugged into its own
individual electrical outlet which has a voltage rating
that matches the rating plate.
This provides the best performance and also prevents
overloading house wiring circuits which could cause a
fire hazard from overheated wires.
Never unplug your refrigerator by pulling on the
power cord. Always grip plug firmly and pull straight
out from the outlet.
Repair or replace immediately all power cords that
have become frayed or otherwise damaged. Do not use
a cord that shows cracks or abrasion damage along its
length or at either end.
When moving the refrigerator away from the
wall, be careful not to roll over or damage the
power cord.
MESURES DE SÉCURITÉ IMPORTANTES.
LISEZ D’ABORD TOUTES LES DIRECTIVES.
AVERTISSEMENT!
RACCORDEMENT ÉLECTRIQUE
Ne coupez ni retirez en aucun cas la troisième broche (mise à la terre) de la fiche du cordon
d’alimentation. Pour votre sécurité, cet appareil doit être correctement mis à la terre.
Le cordon d’alimentation de cet appareil est muni
d’une fiche à 3 broches (mise à la terre) qui se branche
dans une prise murale ordinaire à 3 alvéoles (mise à la
terre) pour réduire au minimum les risques de chocs
électriques.
Faites examiner la prise de courant et le circuit par un
électricien qualifié pour vous assurer que la prise est
correctement mise à la terre.
Si la prise murale est du type standard à 2 alvéoles, il
vous incombe de la faire remplacer par une prise à 3
alvéoles correctement mise à la terre.
Le réfrigérateur doit toujours être branché dans sa
propre prise de courant, dont la tension nominale est
identique à celle indiquée sur la plaque signalétique.
Cette précaution est recommandée pour garantir un
rendement optimum et éviter une surcharge des
circuits électriques de la résidence, ce qui pourrait
créer un risque d’incendie par surchauffe des fils.
Ne débranchez jamais le réfrigérateur en tirant sur le
cordon d’alimentation. Saisissez fermement la fiche du
cordon et tirez droit pour la retirer de la prise.
Réparez ou remplacez immédiatement tout cordon
effiloché ou endommagé. N’utilisez pas un cordon
fendillé ou présentant des signes d’usure.
Lorsque vous déplacez votre réfrigérateur du mur,
faites attention de ne pas le faire rouler sur le cordon
d’alimentation afin de ne pas l’endommager.
4
Consumer Support Troubleshooting Tips Operating InstructionsInstallation InstructionsTroubleshooting Tips Installation Instructions Operating InstructionsTroubleshooting Tips Installation Instructions Safety InstructionsOperating Instructions
VEUILLEZ LIRE ET SUIVRE ATTENTIVEMENT CES MESURES DE SÉCURITÉ.
CONSERVEZ CES DIRECTIVES
READ AND FOLLOW THIS SAFETY INFORMATION CAREFULLY.
SAVE THESE INSTRUCTIONS
About the temperature control dial. ge.com
Turning the dial to 0stops cooling in both compartments—fresh food and freezer. It does not shut off power to the refrigerator.
Temperature Control Dial (on some models)
The temperature control dial has nine
settings plus
0
.
1
is the warmest.
9
is the
coldest. At first, set the dial at
5
.
After using the refrigerator, adjust the
dial if necessary.
Insert a coin into the slot in the middle
of the dial and you can turn the dial to
the setting that is best suited to your needs.
Allow 24 hours for the refrigerator to
get cold.
About the fresh food compartment shelves.
Shelf supports at various levels allow you to custom-space your shelves. Not all features are on all models.
Full-Width Shelves
Some models have a steel wire sliding
shelf, a stationary tempered glass shelf,
a spillproof shelf or two steel wire
stationary shelves. These shelves can be
moved to another place in the fresh food
compartment.
The full-width sliding shelf has stop-locks.
When placed correctly on the shelf
supports, the shelf will stop before coming
completely out of the refrigerator and will
not tilt when you place food on it or
remove food from it.
Half-Width Shelves
One end of the shelf rests on a molded side-
wall support; a bracket on the other end
hooks into a track on the rear cabinet wall.
To remove,
lift the shelf up at front, then off
the support and out of the track.
To replace,
select desired shelf height. With
shelf front raised slightly, hook the
bracket’s top lug into the track, then lower
the shelf onto the support.
NOTE: The shelf to the right of the track is
designed to hook into the right-hand slot; the shelf
to the left is designed to hook into the left-hand slot.
2Lift up and out
1Tilt up
To remove a full-width shelf when
the fresh food compartment door
cannot be opened fully
Lift rear
Pull forward and down
Lift rear
Pull forward
To remove the full-width shelves
5
Spillproof Shelves (on some models)
Spillproof shelves have special edges
to help prevent spills from dripping
to lower shelves. To remove or replace
the shelves, see the above instructions.
Consumer SupportTroubleshooting TipsOperating InstructionsSafety Instructions Installation Instructions
The snacks drawer can be moved to the
most useful location for your family’s
needs.
Snacks Drawer
Not all features are on all models.
About the storage drawers.
6
Fruit and Vegetable Drawers
Excess water that may accumulate in the
bottom of the drawers should be emptied
and the drawers wiped dry.
About the freezer compartment shelves.
Step Shelf
To remove the step shelf:
Lift left side of shelf slightly.
Move shelf to the left to free its right
ends from holes in the cabinet wall.
Lower right side of shelf, move shelf to
the right and take it out.
3
2
1
To replace the step shelf:
With shelf tilted as shown, fit left ends
of shelf into holes in cabinet wall.
Lift left side of shelf slightly, swing shelf
up, fit right ends of shelf into holes in
cabinet wall, and lower shelf into place.
2
1
123
Consumer Support Troubleshooting Tips Operating Instructions Safety InstructionsInstallation Instructions
Consumer SupportTroubleshooting TipsOperating InstructionsSafety Instructions Installation Instructions
About storage drawer and cover removal. ge.com
Not all features are on all models.
Twin Drawer Shelf
To remove:
Remove the drawers.
Reach in, push the front of glass cover
up, and at the same time, pull it forward
as far as it will come.
Tilt it and take it out. Avoid cleaning the cold
glass cover with hot water because the extreme
temperature difference may cause it to break.
Remove the drawer frame. (Always
remove the glass cover before you take
out the drawer frame.)
Lift the frame off the supports at each side
and back, pull it forward, tilt it and take it out.
To replace:
Lower the frame until it rests on the
supports at each side and back.
Replace the glass cover, pushing its rear
edge firmly into the rear frame channel
and gently lowering the front into place.
Replace the drawers.
3
2
1
3
2
1
Drawer and Cover Removal
Drawers can be removed easily by grasping the sides and lifting up slightly while pulling
drawers past the
stop
location.
Full-Width Drawer with
Plastic Cover
To remove the cover,
lift it off its supports,
pull it forward, tilt it and take it out.
Adjustable Humidity Drawer (on some models)
Slide the control all the way to the
HIGH
setting to provide high humidity
recommended for most vegetables.
Slide the control all the way to the
LOW
setting to provide lower humidity levels
recommended for most fruits.
About the automatic icemaker.
A newly-installed refrigerator may take 12 to 24 hours to begin making ice.
Automatic Icemaker (on some models)
The icemaker will produce approximately
100–130 cubes in a 24-hour period,
depending on the freezer compartment
temperature, room temperature, number of
door openings and other use conditions.
If the refrigerator is operated before the water
connection is made to the icemaker, move the
feeler arm to the
STOP
(up) position.
When the refrigerator has been connected
to the water supply, move the feeler arm to
the
ON
(down) position.
The icemaker will fill with water when it cools
to 15°F. A newly-installed refrigerator may take
12 to 24 hours to begin making ice cubes.
Once the icemaker starts to make ice,
it may take up to 48 hours to fill the bin,
depending on the temperature settings
and number of door openings.
You will hear a buzzing sound each time
the icemaker fills with water.
Throw away the first few batches of ice
to allow the water line to clear.
Be sure nothing interferes with the sweep
of the feeler arm.
When the bin fills to the level of the feeler
arm, the icemaker will stop producing ice.
It is normal for several cubes to be joined
together.
If ice is not used frequently, old ice cubes
will become cloudy, taste stale, shrink or
fuse together.
On power switch models, the green power
light will blink if ice cubes get stuck in the
icemaker. To correct this, set the power
switch to
O (off)
and remove the cubes. Set
the power switch to
I (on)
to restart the
icemaker. After the icemaker has been
turned on again, there will be a delay of
about 45 minutes before the icemaker
resumes operation.
NOTE: In homes with lower-than-average water
pressure, you may hear the icemaker cycle multiple
times when making one batch of ice.
Icemaker Accessory Kit
If your refrigerator did not already come
equipped with an automatic icemaker, an
icemaker accessory kit is available at extra cost.
Check the back of the refrigerator for
the specific icemaker kit needed for
your model.
Feeler Arm in
the STOP
(up) positionFeeler Arm in
the (down)ON
position
7
There are 2 types of icemakers:
Power switch model
Feeler arm model
Power Switch
Green Power Light
Icemaker
Feeler Arm
Care and cleaning of the refrigerator.
8
Consumer Support Troubleshooting Tips Operating Instructions Safety InstructionsInstallation Instructions
Cleaning the Outside
The door handles and trim
(on some models). Clean
with a cloth dampened with soapy water. Dry with a
soft cloth.
Keep the outside clean.
Wipe with a clean cloth lightly
dampened with kitchen appliance wax or mild liquid
dish detergent. Dry and polish with a clean,
soft cloth.
The stainless steel panels and door handles
(on some
models) can be cleaned with a commercially available
stainless steel cleaner. Do not use appliance wax or polish
on the stainless steel.
Do not wipe the refrigerator with a soiled dish cloth or wet
towel. These may leave a residue that can erode the paint.
Do not use scouring pads, powdered cleaners, bleach or cleaners
containing bleach because these products can scratch and
weaken the paint finish.
Cleaning the Inside
To help prevent odors,
leave an open box of baking soda
in the fresh food and freezer compartments.
Unplug the refrigerator before cleaning.
If this is not practical, wring excess moisture out of
sponge or cloth when cleaning around switches, lights
or controls.
Use warm water and baking soda solution—about a
tablespoon (15 ml) of baking soda to a quart (1 liter)
of water. This both cleans and neutralizes odors. Rinse
and wipe dry.
After cleaning the door gaskets, apply a thin layer of
petroleum jelly to the door gaskets at the hinge side.
This helps keep the gaskets from sticking and bending
out of shape.
Avoid cleaning cold glass shelves (on some models) with hot water
because the extreme temperature difference may cause them to
break. Handle glass shelves carefully. Bumping tempered glass can
cause it to shatter.
Do not wash any plastic refrigerator parts in the dishwasher.
Condenser
There is no need for routine
condenser cleaning in
normal home operating
environments. However, in
environments that may be
particularly dusty or greasy,
the condenser should be
cleaned periodically for efficient refrigerator operation.
To clean the condenser, turn the temperature control
dial to
0
. Sweep away or vacuum up dust.
For best results, use a brush specially designed for this
purpose. It is available at most appliance parts stores.
Moving the Refrigerator
Be careful when moving the refrigerator away from
the wall. All types of floor coverings can be damaged,
particularly cushioned coverings and those with
embossed surfaces.
Turn the leveling legs at each front corner of the
refrigerator counterclockwise until the rollers support
the refrigerator. Pull the refrigerator straight out and
return it to position by pushing it straight in.
Moving
the refrigerator in a side direction may result in damage
to the floor covering or refrigerator.
When pushing the refrigerator back, make sure you don’t roll over
the power cord or icemaker supply line (on some models).
After rolling the refrigerator back into place, turn the
legs clockwise until the legs again bear the weight of the
refrigerator.
Light Bulb Replacement
To replace a burned-out bulb, unplug the refrigerator
from its electrical outlet, unscrew the bulb when cool
and replace it with an appliance bulb of the same or
lower wattage.
Turning the control to the position does not remove power to 0
the light circuit.
Preparing for Vacation
For long vacations or absences, remove food and
unplug the refrigerator. Move the temperature control
dial to the
0
position, and clean the interior with a
baking soda solution of one tablespoon (15 ml) of
baking soda to one quart (1 liter) of water. Leave the
doors open.
Move the feeler arm to the
STOP
(up) position and
shut off the water supply to the refrigerator.
If the temperature can drop below freezing, have a
qualified servicer drain the water supply system (on
some models) to prevent serious property damage
due to flooding.
Preparing to Move
Secure all loose items such as grille, shelves and drawers
by taping them securely in place to prevent damage.
Be sure the refrigerator stays in an upright position during moving.
Cleaning the condenser coils.
BEFORE YOU BEGIN
Read these instructions completely and carefully.
•IMPORTANT – Save these
instructions for local inspector’s use.
•IMPORTANT – Observe all
governing codes and ordinances.
•Note to Installer – Be sure to leave these
instructions with the Consumer.
•Note to Consumer – Keep these instructions
for future reference.
•Skill level – Installation of this appliance requires
basic mechanical skills.
•Completion time – Refrigerator Installation
15 minutes
Reversing the Door Swing
1 hour
•Proper installation is the responsibility of the
installer.
•Product failure due to improper installation is not
covered under the Warranty.
• Do not install the refrigerator where the temperature
will go below 60°F (16°C) because it will not run often
enough to maintain proper temperatures.
• Install it on a floor strong enough to support it fully
loaded.
REFRIGERATOR LOCATION
Allow the following clearances for ease of installation,
proper air circulation and plumbing and electrical
connections.
• Sides 3/4″ (19 mm)
• Top 1″ (25 mm)
• Back 1″ (25 mm)
CLEARANCES
Leveling legs
near each front corner of the refrigerator
are adjustable. They firmly position the refrigerator
and prevent it from moving when the doors are
opened. Leveling legs should be set so the front of the
refrigerator is raised just enough that the doors close
easily when opened about halfway.
Turn the leveling legs
clockwise to raise
the
refrigerator,
counterclockwise to lower it
.
Rollers
next to the leveling legs allow you to move the
refrigerator away from the wall for cleaning.
Turn the legs counterclockwise until the weight of the
refrigerator is transferred from them to the rollers.
After rolling the refrigerator back into place, turn the
legs clockwise until the legs again bear the weight of
the refrigerator.
ROLLERS AND LEVELING LEGS
If the refrigerator has an icemaker, it will have to be
connected to a cold water line. A water supply kit
(containing copper tubing, shutoff valve, fittings and
instructions) is available at extra cost from your dealer,
by visiting our Website at ge.com (in Canada at
www.geappliances.ca) or from Parts and Accessories,
1.800.661.1616.
WATER SUPPLY TO THE ICEMAKER
(on some models)
9
Installation Instructions
Models 16, 17, 18
If you have questions, call 1.800.GE.CARES
or visit our Website at:
ge.com
In Canada, call 1.800.561.3344
or Visit our Website at:
www.geappliances.ca
10
WHAT YOU WILL NEED
•Copper or GE SmartConnect™Refrigerator Tubing
kit, 1/4″outer diameter to connect the refrigerator
to the water supply. If using copper, be sure both
ends of the tubing are cut square.
To determine how much tubing you need: measure
the distance from the water valve on the back of the
refrigerator to the water supply pipe. Then add 8′
(2.4 m). Be sure there is sufficient extra tubing
(about 8 [2.4 m] coiled into 3 turns of about 10′ ″
[25 cm] diameter) to allow the refrigerator to move
out from the wall after installation.
INSTALLING THE WATER LINE (ON SOME MODELS)
Installation Instructions
BEFORE YOU BEGIN
Recommended copper water supply kits are WX8X2,
WX8X3 or WX8X4, depending on the amount of
tubing you need. Approved plastic water supply lines
are GE SmartConnect™Refrigerator Tubing
(WX08X10006, WX08X10015 and WX08X10025).
When connecting your refrigerator to a GE Reverse
Osmosis Water System, the only approved installation
is with a GE RVKit. For other reverse osmosis water
systems, follow the manufacturer’s recommendations.
This water line installation is not warranted by the
refrigerator or icemaker manufacturer. Follow these
instructions carefully to minimize the risk of expensive
water damage.
Water hammer (water banging in the pipes) in house
plumbing can cause damage to refrigerator parts and
lead to water leakage or flooding. Call a qualified
plumber to correct water hammer before installing
the water supply line to the refrigerator.
To prevent burns and product damage, do not hook
up the water line to the hot water line.
If you use your refrigerator before connecting the
water line, make sure the feeler arm is in the
STOP
(up) position.
Do not install the icemaker tubing in areas where
temperatures fall below freezing.
When using any electrical device (such as a power
drill) during installation, be sure the device is double
insulated or grounded in a manner to prevent the
hazard of electric shock, or is battery powered.
All installations must be in accordance with local
plumbing code requirements.
1
WHAT YOU WILL NEED (CONT.)
GE SmartConnect™Refrigerator Tubing Kits are
available in the following lengths:
6′ (1.8 m) – WX08X10006
15′ (4.6 m) – WX08X10015
25′ (7.6 m) – WX08X10025
Be sure that the kit you select allows at least 8′(2.4 m)
as described above.
NOTE: The only GE approved plastic tubing is that
supplied in GE SmartConnect™Refrigerator Tubing
kits. Do not use any other plastic water supply line
because the line is under pressure at all times. Certain
types of plastic will crack or rupture with age and
cause water damage to your home.
•A GE water supply kit (containing tubing, shutoff
valve and fittings listed below) is available at extra
cost from your dealer or from Parts and Accessories,
1.800.661.1616.
•A cold water supply. The water pressure must be
between 20 and 120 p.s.i. (1.4–8.1 bar).
•Power drill.
•1/2″or adjustable wrench.
•Straight and Phillips
blade screwdriver.
•Two 1/4″outer diameter compression nuts and
2 ferrules (sleeves)—to connect
the copper tubing to the shutoff
valve and the refrigerator water valve.
OR
•If you are using a GE SmartConnect™Refrigerator
Tubing kit, the necessary fittings are preassembled
to the tubing.
•If your existing copper water line has a flared fitting
at the end, you will need an adapter (available at
plumbing supply stores) to connect the water line to
the refrigerator OR you can cut off the flared fitting
with a tube cutter and then use a compression
fitting. Do not cut formed end from GE
SmartConnect™Refrigerator tubing.
•Shutoff valve to connect to the cold water line.
The shutoff valve should have a water inlet with a
minimum inside diameter of 5/32 at the point of″
connection to the COLD WATER LINE. Saddle-type
shutoff valves are included in many water supply kits.
Before purchasing, make sure a saddle-type valve
complies with your local plumbing codes.
Installation Instructions
Install the shutoff valve on the nearest frequently used drinking water line.
SHUT OFF THE MAIN WATER
SUPPLY AND UNPLUG
REFRIGERATOR
Turn on the nearest faucet (counterclockwise) long
enough to clear the line of water.
1
11
Choose a location for the valve that is easily
accessible. It is best to connect into the side of a
vertical water pipe. When it is necessary to connect
into a horizontal water pipe, make the connection
to the top or side, rather than at the bottom, to
avoid drawing off any sediment from the water pipe.
Drill a 1/4″hole in the water pipe (even if using a
self-piercing valve), using a sharp bit. Remove any
burrs resulting from drilling the hole in the pipe.
Take care not to allow water to drain into the drill.
Failure to drill a 1/4″ hole may result in reduced
ice production or smaller cubes.
DRILL THE HOLE FOR THE VALVE
2
Fasten the shutoff valve to the cold water pipe with
the pipe clamp.
Tighten the clamp screws until the sealing washer
begins to swell.
NOTE: Do not overtighten or you may crush the
tubing.
NOTE: Commonwealth of Massachusetts Plumbing
Codes 248CMR shall be adhered to. Saddle valves
are illegal and use is not permitted in Massachusetts.
Consult with your licensed plumber.
FASTEN THE SHUTOFF VALVE
3
Washer
Inlet End
Clamp Screw
Vertical Cold
Water Pipe
Saddle-Type
Shutoff Valve
Pipe Clamp FLUSH OUT THE TUBING
Turn the main water supply on (counterclockwise)
and flush out the tubing until the water is clear.
Shut the water off at the water valve after about
one quart (1 liter) of water has been flushed
through the tubing.
6
CONNECT THE TUBING
TO THE VALVE
Place the compression nut and ferrule (sleeve)
for copper tubing onto the end of the tubing and
connect it to the shutoff valve.
Make sure the tubing is fully inserted into the
valve. Tighten the compression nut securely.
For plastic tubing from a GE SmartConnect™
Refrigerator Tubing kit, insert the molded end
of the tubing into the shutoff valve and tighten
compression nut until it is hand tight, then tighten
one additional turn with a wrench. Overtightening
may cause leaks.
NOTE: Commonwealth of Massachusetts Plumbing
Codes 248CMR shall be adhered to. Saddle valves
are illegal and use is not permitted in Massachusetts.
Consult with your licensed plumber.
5
Saddle-Type
Shutoff Valve
Compression
Nut
SmartConnect™
Tubing
Packing Nut
Outlet Valve Ferrule (sleeve)
ROUTE THE TUBING
Route the tubing between the cold water line and
the refrigerator.
Route the tubing through a hole drilled in the wall
or floor (behind the refrigerator or adjacent base
cabinet) as close to the wall as possible.
NOTE: Be sure there is sufficient extra tubing
(about 8 feet [244 cm] coiled into 3 turns of about
10″[25 cm] diameter) to allow the refrigerator to
move out from the wall after installation
.
4
Installation Instructions
12
CONNECT THE TUBING
TO THE REFRIGERATOR
NOTES:
•Before making the connection to the refrigerator,
be sure the refrigerator power cord is not plugged
into the wall outlet.
•We recommend installing a water filter if your water
supply has sand or particles that could clog the
screen of the refrigerator’s water valve. Install it in
the water line near the refrigerator. If using GE
SmartConnect™Refrigerator Tubing kit, you will
need an additional tube (WX08X10002) to connect
the filter. Do not cut plastic tube to install filter.
Remove the access cover.
Remove the plastic flexible
cap from the water valve
(refrigerator connection).
Place the compression nut and ferrule (sleeve)
onto the end of the tubing as shown. On GE
SmartConnect™Refrigerator Tubing kit,
the nuts are already assembled to the tubing.
Insert the end of the tubing into the water valve
connection as far as possible. While holding the
tubing, tighten the fitting.
For plastic tubing from a GE SmartConnect™
Refrigerator Tubing kit, insert the molded end
of the tubing into the shutoff valve and tighten
compression nut until it is hand tight, then
tighten one additional turn with a wrench.
Overtightening may cause leaks.
Fasten the tubing into the clamp provided
to hold it in a vertical position. You may need
to pry open the clamp.
7TURN THE WATER
ON AT THE
SHUTOFF VALVE
Tighten any connections
that leak.
8
Tubing Clamp
1/4″Compression
Nut
Ferrule (sleeve)
SmartConnect™
Tubing
Refrigerator Connection
1/4″Copper
Tubing
PLUG IN THE REFRIGERATOR
Arrange the coil of tubing so that it does not vibrate
against the back of the refrigerator or against the
wall. Push the refrigerator back to the wall.
9
Reattach the access cover.
INSTALLING THE WATER LINE (CONT.)
1
On power switch models, set the icemaker power
switch to the
l (on)
position. On feeler arm models,
move the feeler arm to the
ON
(down) position. The
icemaker will not begin to operate until it reaches
its operating temperature of 15°F (–9°C) or below.
It will then begin operation automatically.
NOTE: In lower water pressure conditions, the
water valve may turn on up to 3 times to deliver
enough water to the icemaker.
START THE ICEMAKER
Power
switch
Power switch model
Feeler Arm in the
STOP (up) position
Feeler Arm in
the ON (down) position
Feeler arm model
10
13
Installation Instructions
REVERSING THE DOOR SWING
2
When reversing the door swing:
•Read the instructions all the way through before
starting.
•Handle parts carefully to avoid scratching paint.
•Set screws down by their related parts to avoid using
them in the wrong places.
•Provide a non-scratching work surface for
the doors.
IMPORTANT: Once you begin, do not move the
cabinet until door-swing reversal is completed.
These instructions are for changing the hinges from
the right side to the left side—if you ever want to change
the hinges back to the right side, follow these same
instructions and reverse all references to left and right.
IMPORTANT NOTES
Phillips screwdriver
TOOLS REQUIRED
Masking tape
T20 or T25 Torxdriver
(needed for some models)
5/16 hex-head ″
socket driver
5/16 open-end″
wrench
Putty knife or thin-blade
screwdriver
2.1 Tape the door shut with masking tape.
2.2 With a 5/16″hex-head socket driver, remove the
screws that hold the top hinge to the cabinet.
REMOVE THE FREEZER DOOR
2
2.3 Lift the hinge straight up to free the hinge pin
from the socket in the top of the door and set it
aside, along with its screws.
Top Hinge
2.6 Transfer the 2 screws from the opposite side of
the cabinet to the screw holes vacated by the
top hinge removal.
2.5 Set the door on a non-scratching surface with
the outside up.
2.4 Remove the tape and tilt the door away from the
cabinet. Lift it off the center hinge pin.
1.1 Unplug the refrigerator from its electrical
outlet.
1.2 Empty all door shelves, including the dairy
compartment.
CAUTION: Do not let either door drop to the
floor. To do so could damage the door stop.
BEFORE YOU START
1
Installation Instructions
3.1 Tape the door shut with masking tape.
REMOVE THE FRESH FOOD DOOR
3
3.4 Set the door outside-up on a non-scratching surface.
3.3 Remove the tape and tilt the door away from the
cabinet. Lift the door from the pin in the bottom
hinge bracket. (If the plastic washer sticks to the
door bottom, put it back on the hinge.)
3.2 Using a 5/16″hex-head socket screwdriver and
a 5/16″ open-end wrench, remove the two
screws holding the center hinge to the cabinet.
Lift the center hinge to free its pin from the
socket in the top of the door, and set hinge and
screws aside. Be careful not to lose the center
hinge spacer and washer.
3.7 Take one of the screws removed in step 2 and start
it in the outermost screw hole on the opposite side.
Do not drive it all the way down—leave enough space
under the screw head for thickness of the bracket.
14
REVERSING THE HARDWARE
4
REVERSING THE DOOR SWING (CONT.)
2
3.5 Transfer the two screws from the opposite side of the
cabinet to the screw holes vacated by the center
hinge removal.
3.6 Transfer the washer (if your model has one) to the
opposite side.
3
REMOVE THE FRESH FOOD DOOR (CONT.)
4.1 Move the bottom hinge bracket and plastic washer from
the right side to the left side.
Plastic
Washer
Hinge
Bracket
Switch the hinge pin to the
opposite side of the bracket.
Installation Instructions
4.2 Interchange hinge and screws at top right with
screws at top left of cabinet. Do not tighten screws
on hinge side at this time.
NOTES:
•Some hinges have four holes. Which holes you
use for installing the hinge depends on which
side you install the hinge.
•The outer edge of the hinge should be parallel
to the edge of the case for correct installation.
Installing the hinge on the left. Installing the hinge on the right.
REVERSING THE DOOR HANDLES
5
5.1.2 Remove the handle.
5.1.3 Remove the screws from the right edge of the
door top and insert them into the handle screw
holes on the opposite side.
Top
Screws
for Handle
Holes
Plug
15
5.3 Reinstall the fresh food door handle
5.3.1 Attach the handle to
the right side of the
door with screws at
the top and under
the handle plug.
5.3.2 Reinstall the
handle plug.
REVERSING THE HARDWARE
(CONT.)
4
5.1 Transfer fresh food door handle
5.1.1 Remove the handle plug using a tape-tipped
putty knife under the edge, and remove the
screw underneath. Remove the two screws
holding the handle to the top of the door.
5.1.4 Remove plug button from the top hinge hole on
the left side of the door and insert it into the hole
on the opposite side that was vacated by removal of
the top hinge.
Plug Button
5.1.5 Pull the plug button from the front of the door
and transfer it to the opposite side.
5.2 Transfer door stop
5.2.1 Move the metal or plastic door stop and
screws from the right side to the left side.
To reattach the
handle on the
opposite side.
Plug Button
Metal Door Stop
Left Side
REVERSING THE DOOR
HANDLES (CONT.)
5
Right Side
Plastic Door Stop
Left Side
Right Side
Installation Instructions
5.4.3 Remove the screw from the
right top edge of the door
and insert it into the
handle screw hole on the
left side.
5.4.4 Transfer the door stop as shown in preceding
section 5.2.
5.4.5 Attach the handle to the
right edge of the door
with screws at top and
bottom, using bottom holes
vacated by removal of the
door stop screws.
Top
Bottom
5.4 Transfer Freezer Door Handle
5.4.1 Remove the screw
holding the handle
to the top of the
door and the two
screws holding the
handle to the bottom
of the door.
5.4.2 Remove the handle.
16
6.1.2 Insert the pin on the center hinge into the socket in
the top of the door. Place the spacer, then the
washer, on the hinge pin.
NOTE: The center hinge must
be turned over as shown when
mounted on the left side.
Plastic Washer
and Spacer
Hinge Pin
6.2 Re-hang the freezer door
6.2.1 Lower the freezer door
onto the center hinge
pin. Be sure the
washer and spacer
are in place on the pin.
RE-HANGING THE DOORS (CONT.)
6
Center Hinge Pin
Plastic Washer
and Spacer
REVERSING THE DOOR SWING (CONT.)
2
6.1.3 Tilt the door toward the cabinet. As the door is
brought into position, slide the hinge under the head
of the screw which earlier had been partly driven into
the outermost hole. Insert the remaining screw, then
tighten both screws securely.
6.1 Re-hang the fresh food door
6.1.1 Lower the fresh food door onto the
bottom hinge pin. Be sure the washer
is in place on the pin.
RE-HANGING THE DOORS
6
Plastic
Washer
Hinge
Bracket
6.2.2 Tilt the door toward the cabinet, lifting the top hinge
so the pin fits into the socket on the top of the door.
6.2.3. Make sure the door is slightly above the top of the
cabinet and the gap between the doors is even across
the front. Tighten the top hinge screws. Do not
overtighten these screws–tighten them until they are
just snug, then turn them another one-half turn.
REVERSING THE DOOR HANDLES (CONT.)
5
20
Consumer Product Ownership Registration
Dear Customer:
Thank you for purchasing our product and thank you for placing your confidence in us.
We are proud to have you as a customer!
Follow these three steps to protect your new appliance investment:
Important: If you did not get a registration card with your
product, detach and return the form on the next page
to ensure that your product is registered, or register
online at ge.com. The top card is for products installed
in the U.S. The bottom card is for products installed in
Canada.
12 3
Model Number Serial Number
Complete and mail
your Consumer
Product Ownership
Registration today.
Have the peace of
mind of knowing we
can contact you in
the unlikely event of
a safety modification.
After mailing the
registration below,
store this document
in a safe place. It
contains information
you will need should
you require service.
Our service number is
800 GE CARES
(800.432.2737).
Read your Owner’s
Manual carefully.
It will help you
operate your new
appliance properly.
GE Service Protection Plus™
GE, a name recognized worldwide for quality and dependability together with Assurant Solutions, offers
you Service Protection Plus™—comprehensive protection on your appliances.*
Benefits Include:
• Prompt, reliable service from GE Authorized Servicers
• Convenient hours designed to suit your busy schedule
• Quality replacement parts
• The dependability of GE, a name recognized and trusted worldwide
• Ask about our interest-free payment plans
With Service Protection Plus you can expect:
• An extended service plan that limits unexpected repair bills
• Service coverage for most major brands
• Unlimited service calls for the length of your contract, or credit toward a replacement product
• Service coverage for covered operating parts and labor on appliances and home electronics that fail during normal
single family household use
• Your satisfaction is our goal. We strive to provide you with excellent service in a professional and timely manner.
Place your confidence in GE and call us in the U.S. toll-free at 1.800.626.2224 for more information.
*Most brands covered up to 15 years old in the continental U.S.
SPP is a trademark of General Electric Company.
Produkt Specifikationer
| Mærke: | GE |
| Kategori: | Køleskab |
| Model: | GTS18GCSWW |
Har du brug for hjælp?
Hvis du har brug for hjælp til GE GTS18GCSWW stil et spørgsmål nedenfor, og andre brugere vil svare dig
Køleskab GE Manualer
10 Februar 2025
17 Januar 2025
17 Januar 2025
17 Januar 2025
17 Januar 2025
17 Januar 2025
13 Januar 2025
12 Januar 2025
15 December 2024
15 December 2024
Køleskab Manualer
- Køleskab Daewoo
- Køleskab Salton
- Køleskab EAS Electric
- Køleskab Sheffield
- Køleskab Finlux
- Køleskab Atlas
- Køleskab PITSOS
- Køleskab Leisure
- Køleskab Mestic
- Køleskab Coldtainer
- Køleskab AEG-Electrolux
- Køleskab John Lewis
- Køleskab Zanussi
- Køleskab Zerowatt
- Køleskab Philco
Nyeste Køleskab Manualer
30 Maj 2025
29 Maj 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
6 April 2025
6 April 2025
6 April 2025
6 April 2025