GE Profile PHD23BYWFS Manual

GE Køleskab Profile PHD23BYWFS

Læs gratis den danske manual til GE Profile PHD23BYWFS (8 sider) i kategorien Køleskab. Denne vejledning er vurderet som hjælpsom af 27 personer og har en gennemsnitlig bedømmelse på 4.6 stjerner ud af 14 anmeldelser. Har du et spørgsmål om GE Profile PHD23BYWFS, eller vil du spørge andre brugere om produktet?

Side 1/8
LOCATING THE ANTI-TIP FLOOR
BRACKET
Place the anti-tip floor bracket locator template
(included inside the anti-tip kit) onto the floor up
against the rear wall, within W, and in line with the
desired location of the RH side of the refrigerator
(see Figure 1).
Place the anti-tip floor bracket onto the locator
template with its RH floor holes lined up with the floor
13 ½" from the edge of the sheet or the RH side of the
refrigerator.
Hold down in position and use the anti-tip floor bracket
as a template for marking the holes based upon your
configuration and type of construction as shown in Step
3. Mark the hole locations with a pencil, nail or awl.
NOTE:
It is REQUIRED to use at least 2 screws to mount
the floor bracket (one on each side of the anti-tip
floor bracket). Both must be into either the wall or the
floor. Figure 2 indicates all the acceptable mounting
configurations for screws. Identify the screw holes on
the anti-tip floor bracket for your configuration.
MEASURE CABINET OPENING
AVAILABLE VS. REFRIGERATOR WIDTH
Measure width of cabinet opening where
refrigerator will be placed, W.
Be sure to account for any countertop overhang,
baseboard thickness and any clearance desired.
Width, W, should not be less than 36”. The
refrigerator will be placed approximately in the
middle of this opening.
MATERIALS YOU MAY NEED (not included)
TOOLS YOU WILL NEED
Pencil
1/8” (3 mm) Drill Bit and
Electric or Hand Drill
Tape measure
5/16” (8 mm) Nut Driver
Lag Bolts
1/4” (6 mm) x 1-1/2” (38 mm)
Anchor Sleeves
1/2” (12 mm) OD
For Anti-Tip Bracket Mounted on CONCRETE Floors Only
Drill Bit Appropriate for Anchors
1
Baseboard
Thickness or
Countertop
Overhang
(Whichever Is
Larger) Plus
Any Desired
Clearance
Rear Wall
Front
RH Side
A
2
B
C
1
W
REFRIGERATOR
31-1000632-3 03-25
Floor – Wood
(2 Holes)
Figure 1 Installation Overview
Base Plate
on the Refrigerator
2 Wall Holes
RH Side of Refrigerator
Floor – Concrete
(2 Holes)
13 ½"
Locator
Template Sheet
Floor Bracket
to Install
RH Holes
Rear RH
Corner of
Cabinet Wall
NOTE:
If you did not receive an anti-tip bracket with your
purchase, call 1.800.GECARES to receive one at no
cost. (In Canada, call 1.800.561.3344.)
For installation instructions of the bracket,
visit: www.GEAppliances.com.
(In Canada, www.GEAppliances.ca.)
WARNING
Tip Over Hazard.
Built-in style models (models PJD, PJE, PXD, CJE and
CXE) are top heavy, especially with any doors open.
These models must be secured with the anti-tip floor
bracket to prevent tipping forward, which could result
in death or serious injury. Read and follow the entire
installation instructions for installing the anti-tip floor
bracket packed with your refrigerator.
Anti-Tip
Floor Bracket
PJD, PJE, PXD, CJE and CXE Models Only
Installation
Instructions


Produkt Specifikationer

Mærke: GE
Kategori: Køleskab
Model: Profile PHD23BYWFS

Har du brug for hjælp?

Hvis du har brug for hjælp til GE Profile PHD23BYWFS stil et spørgsmål nedenfor, og andre brugere vil svare dig




Køleskab GE Manualer

GE

GE C29DP4TW2 Manual

10 September 2025
GE

GE C29DM5TS5 Manual

9 September 2025
GE

GE PJD23BYWFS Manual

25 August 2025
GE

GE PBV10RGTBB Manual

13 August 2025
GE

GE PGD29BYTFS Manual

7 August 2025
GE

GE TPG24PRDBS Manual

7 August 2025
GE

GE CAE28DM5TS5 Manual

7 August 2025
GE

GE CIC36RP2VS1 Manual

7 August 2025
GE

GE DSHF9NGYWW Manual

7 August 2025

Køleskab Manualer

Nyeste Køleskab Manualer