GE Profile PXD22BYPFS Manual

GE Køleskab Profile PXD22BYPFS

Læs gratis den danske manual til GE Profile PXD22BYPFS (8 sider) i kategorien Køleskab. Denne vejledning er vurderet som hjælpsom af 10 personer og har en gennemsnitlig bedømmelse på 4.8 stjerner ud af 5.5 anmeldelser. Har du et spørgsmål om GE Profile PXD22BYPFS, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/8
LOCATING THE ANTI-TIP FLOOR
BRACKET
Place the anti-tip floor bracket locator template
(included inside the anti-tip kit) onto the floor up
against the rear wall, within W, and in line with the
desired location of the RH side of the refrigerator
(see Figure 1).
Place the anti-tip floor bracket onto the locator
template with its RH floor holes lined up with the floor
13 ½" from the edge of the sheet or the RH side of the
refrigerator.
Hold down in position and use the anti-tip floor bracket
as a template for marking the holes based upon your
configuration and type of construction as shown in Step
3. Mark the hole locations with a pencil, nail or awl.
NOTE:
•
It is REQUIRED to use at least 2 screws to mount
the floor bracket (one on each side of the anti-tip
floor bracket). Both must be into either the wall or the
floor. Figure 2 indicates all the acceptable mounting
configurations for screws. Identify the screw holes on
the anti-tip floor bracket for your configuration.
MEASURE CABINET OPENING
AVAILABLE VS. REFRIGERATOR WIDTH
Measure width of cabinet opening where
refrigerator will be placed, W.
Be sure to account for any countertop overhang,
baseboard thickness and any clearance desired.
Width, W, should not be less than 36”. The
refrigerator will be placed approximately in the
middle of this opening.
MATERIALS YOU MAY NEED (not included)
TOOLS YOU WILL NEED
Pencil
1/8” (3 mm) Drill Bit and
Electric or Hand Drill
Tape measure
5/16” (8 mm) Nut Driver
Lag Bolts
1/4” (6 mm) x 1-1/2” (38 mm)
Anchor Sleeves
1/2” (12 mm) OD
For Anti-Tip Bracket Mounted on CONCRETE Floors Only
Drill Bit Appropriate for Anchors
1
Baseboard
Thickness or
Countertop
Overhang
(Whichever Is
Larger) Plus
Any Desired
Clearance
Rear Wall
Front
RH Side
A
2
B
C
1
W
REFRIGERATOR
31-1000632-3 03-25
Floor – Wood
(2 Holes)
Figure 1 – Installation Overview
Base Plate
on the Refrigerator
2 Wall Holes
RH Side of Refrigerator
Floor – Concrete
(2 Holes)
13 ½"
Locator
Template Sheet
Floor Bracket
to Install
RH Holes
Rear RH
Corner of
Cabinet Wall
NOTE:
If you did not receive an anti-tip bracket with your
purchase, call 1.800.GECARES to receive one at no
cost. (In Canada, call 1.800.561.3344.)
For installation instructions of the bracket,
visit: www.GEAppliances.com.
(In Canada, www.GEAppliances.ca.)
WARNING
Tip Over Hazard.
Built-in style models (models PJD, PJE, PXD, CJE and
CXE) are top heavy, especially with any doors open.
These models must be secured with the anti-tip floor
bracket to prevent tipping forward, which could result
in death or serious injury. Read and follow the entire
installation instructions for installing the anti-tip floor
bracket packed with your refrigerator.
Anti-Tip
Floor Bracket
PJD, PJE, PXD, CJE and CXE Models Only
Installation
Instructions
Installation Instructions
LOCATING THE ANTI-TIP FLOOR
BRACKET (cont.)
2
Recommended Installation
– Wood
Recommended Installation
– Concrete
Minimum Acceptable #1 –
Wall Plate Stud
Minimum Acceptable #2
– Wood Floor
Minimum Acceptable #3
– Concrete Floor
Figure 2 – Acceptable Screw
Placement Locations
CONCRETE Wall and Floor Construction:
• Anchors required (not provided):
4 each 1/4” (6 mm) x 1-1/2” (38 mm) lag bolts 4
each 1/2” (12 mm) O.D. sleeve anchors
• Drill the recommended size holes for the
anchors into the concrete at the center of the
holes marked in Step 2.
• Install the sleeve anchors into the drilled holes.
2. Remove the locator template from the floor.
• Install the lag bolts through the anti-tip floor
bracket and tighten appropriately.
WOOD Wall and TILE Floor Construction:
• For this special case, locate the 2 wall holes
identified in Fig. 2. Drill an angled 1/8” (3 mm)
pilot hole (approx. as shown in Fig. 3) in the
center of each hole.
• Mount the anti-tip floor bracket using the
Minimum Acceptable Installation #1, as
illustrated in Fig. 2.
C
B
ANTI-TIP BRACKET INSTALLATION
WOOD Wall and Floor Construction:
•
Drill the appropriate number of 1/8” (3 mm)
pilot holes in the center of each floor bracket
hole being used (a nail or awl may be used if
a drill is not available) AND remove the locator
template from the floor.
• Mount the anti-tip floor bracket by fastening the
2, or recommended 4, #10 screws included,
tightly into place as illustrated in Figure 3.
3
A
POSITIONING THE REFRIGERATOR
TO ENGAGE THE ANTI-TIP FLOOR
AND BASE BRACKETS
Before pushing the refrigerator into the opening,
plug the power cord into the receptacle and
connect waterline (if equipped). Check for leaks.
Locate the refrigerator’s RH side and move back
approximately in line with the RH side of the cabinet
opening, W. This should position the anti-tip floor
bracket to engage the anti-tip base bracket on the
refrigerator.
Gently roll the refrigerator back into the cabinet
opening until it comes to a complete stop. Check to
see if the refrigerator front lines up with the cabinet
front face. If not, carefully rock the refrigerator
forward and backward until engagement occurs and
you notice that the refrigerator is fully pushed up
against the rear wall.
If Applicable: Adjust the rear (and front) wheel
height settings to fully engage the rear anti-tip
brackets, while also aligning the refrigerator front
with the cabinet front face.
4
A
C
B
D
Figure 3 – Attachment to Wall and
Floor
NOTE:
If you pull the refrigerator out and away from the wall
for any reason, make sure the anti-tip floor bracket is
engaged when the refrigerator is pushed back against
the rear wall.
Rear RH
Corner of the
Refrigerator
Floor
Wall
Plate
Stud
Floor
Bracket
2 Screws
Must Enter
Wood or
Metal Stud
Wall
2
31-1000632-3 03-25

Produkt Specifikationer

Mærke: GE
Kategori: Køleskab
Model: Profile PXD22BYPFS

Har du brug for hjælp?

Hvis du har brug for hjælp til GE Profile PXD22BYPFS stil et spørgsmål nedenfor, og andre brugere vil svare dig


Køleskab GE Manualer

GE

GE GDR20DTERWW Manual

28 Juli 2025
GE

GE Profile PPV10R5YR Manual

16 Juli 2025
GE

GE Profile PPV08R5YR Manual

15 Juli 2025
GE

GE Profile PPV10R5YLBB Manual

15 Juli 2025
GE

GE Profile PPV10R5YRSS Manual

15 Juli 2025
GE

GE Profile PPV08R5YRSS Manual

15 Juli 2025
GE

GE Profile PPV10R5YLSS Manual

15 Juli 2025
GE

GE GSE 30 VHT BB SS Manual

30 Juni 2025
GE

GE Profile PHD23BYWFS Manual

21 Juni 2025
GE

GE Profile PXD22BYPFS Manual

17 Juni 2025

Køleskab Manualer

Nyeste Køleskab Manualer

Exquisit

Exquisit KS185-4-HE-040E Manual

1 August 2025
Midea

Midea MR237W Manual

1 August 2025
Etna

Etna KKS7102 Manual

1 August 2025
Amica

Amica EKSS 367 200 Manual

1 August 2025
Midea

Midea MDRB521MGA28O Manual

1 August 2025
Amica

Amica KGCR 387 101 MS Manual

1 August 2025
Amica

Amica KGCR 387 101 B Manual

1 August 2025
Amica

Amica FK3666.2DFZHC Manual

1 August 2025
Grundig

Grundig GSBS13320FGB Manual

1 August 2025
Amica

Amica FK3076N.2DFX Manual

1 August 2025