Geba Tronic DC2 ECO Manual

Geba Tronic Garage døråbner DC2 ECO

Læs gratis den danske manual til Geba Tronic DC2 ECO (3 sider) i kategorien Garage døråbner. Denne vejledning er vurderet som hjælpsom af 62 personer og har en gennemsnitlig bedømmelse på 4.5 stjerner ud af 31.5 anmeldelser. Har du et spørgsmål om Geba Tronic DC2 ECO, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/3

INSTRUCTIONS FOR ASSEMBLY AND USE

Tubular Drive Control

DC2-ECO - SL 433 MHz

The DC2-ECO is a modern and safe alternative to traditional Tubular

Drive key-switches that have to be hard wired.

To open or close a roller-shutter only the correct button on the hand

transmitter or the indoor keypad has to be pressed.

The most important characteristics of the DC2-ECO are:

➢economic installation

➢easy to use and programme

➢water proof housings - IP 54

➢ A maximum of security through:

➢transmission of a different unpredictable signal every time (Hopping Code)

➢up to 100 million different coding possibilities

Technical Data:

240 V series

Supply voltage *240 V AC 50 Hz 2,3 VA

Outputs 1 &. 2 1 x NO, NC relay contact,

isolated,10 A 250 V

Output 3 1 x NO, NC relay contact,

isolated, 5 A 250 V

Wiring 1.5 mm2max.,

Operating- -20 ˚C to +60 ˚C

temperature

* Further voltage variations upon request

geba GmbH is released its obligations regarding the guarantee and product liability if - with-

out prior permission - the unit has been modified, or if the installation is not in accordance

with our instruction manual.

The installer is responsible for adherence to the EMC- and low voltage regulations.

industrial controls

Caution!

Using the DC2-ECO with an industrial door, you must install the corresponding

security components, if the doorpanel weight is > 15kg. Electrical connections

may be carried out by skilled electrical personnel only.

Please note that all the keypad units are battery powered. The normal battery

life is dependent on the frequency of use of the appliance. For safety reasons

we advise replacement of the keypad batteries every 6 months.

BA-DC2-ECO-GB 08.02.2002 16:27 Uhr Seite 1

Dear customer,

The remote control that you have purchased is one of our highest quality technical

products. We have taken the greatest care during manufacture to ensure that this

microprocessor controlled encoder reaches you in faultless condition. However in the

unusual event of suspected equipment failure please return the appliance together

with the enclosed warranty document to your dealer or direct to our factory.

The extent of warranty exclusively refers to the free repair of malfunctions of the

appliance, which demonstrably are caused by faults in production or defective

material, inclusive of spare parts required for this purpose.

Please read the instructions of use carefully before you start programming

the receiver !

WARRANTY-DOCUMENT

On the device described below we grant a warranty of

2 years

Type: Tubular Drice Control DC2-ECO 433 MHz

Production date: ___________________________________________

Sales date: ___________________________________________

Dealers address:

industrial controls

2 5

Description of the Appliance

Transmitters and Receivers

The self-learning remote control system is offered with a 2-channel or 4-channelDC 2-ECO

remote control transmitter, and a four channel indoor keypad.

The transmitters are programmed at the factory.

The Hopping Code security feature used in this system prevents access by unauthorised

transmitters. To operate the system it is only necessary to press and hold for a moment the

selected button on the remote control or indoor keypad.

Receiver & Transmitter Programming

Before the remote control can be used you first have to programme the individual transmitters

into the receiver. (Self Learning System)

First, to be sure that any previous programming is removed, press the button situated

on the receiver and keep it pressed for about 7 seconds until the lights (LEDs) on the

receiver illuminate. Immediately release the button and when the lights go

out the memory is completely cleared.

To program a new transmitter press the button on the receiver until the light starts to flash,

then immediately press any button on the transmitter and hold it until the light gives a

steady glow. Release the button and wait until the light stops flashing. The transmitter has

now been programmed into the receiver and is ready for function.

The first activation of the transmitter operates relay 2 for approximately

two minutes. This operation can be interrupted by activating the transmitter again

during the run time.

The second activation of the transmitter operates relay 1 for approximately two

minutes. This operation can also be interrupted by activating the transmitter

again during the run time. (e.g. Up - Stop Down - Stop)

RECEIVER DIAGRAM

Trafo

LED’s

Receiver module

Antenna

Push Button

STOP

N N N L1

BA-DC2-ECO-GB 08.02.2002 16:27 Uhr Seite 2

Produkt Specifikationer

Mærke:	Geba Tronic
Kategori:	Garage døråbner
Model:	DC2 ECO

Har du brug for hjælp?

Hvis du har brug for hjælp til Geba Tronic DC2 ECO stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Garage døråbner Geba Tronic Manualer

Geba Tronic TCS - Cody - Light Manual

26 Januar 2023

Geba Tronic ROLLOTIMER Standard Manual

18 December 2022

Geba Tronic TCS - Cody 1- 1 Manual

7 December 2022

Geba Tronic DC2 ECO Manual

25 Oktober 2022

Geba Tronic DC 2 EN ECO Manual

22 Oktober 2022

Geba Tronic DC MiniMax 3 S Manual

21 Oktober 2022

Geba Tronic TCS - Cody 2 Manual

7 Oktober 2022

Garage døråbner Manualer

Nyeste Garage døråbner Manualer

Meross MSG150 Manual

28 September 2025

Sommer S 9080 pro+ S3 Manual

2 September 2025

Schellenberg Smart Drive XL Manual

17 August 2025

MSW -GDOOR-005B Manual

17 August 2025

MSW -GDOOR-002A Manual

17 August 2025

MSW -GDOOR-003B Manual

17 August 2025

MSW -GDOOR-001A Manual

17 August 2025

Schellenberg Drive Action Manual

16 August 2025

MSW -GDOOR-003A Manual

15 August 2025

Sommer S 9080 tiga+ Manual

14 August 2025