Geba Tronic TCS - Cody 2 Manual

Geba Tronic Garage døråbner TCS - Cody 2

Læs gratis den danske manual til Geba Tronic TCS - Cody 2 (4 sider) i kategorien Garage døråbner. Denne vejledning er vurderet som hjælpsom af 29 personer og har en gennemsnitlig bedømmelse på 4.0 stjerner ud af 15 anmeldelser. Har du et spørgsmål om Geba Tronic TCS - Cody 2, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

Instructions for Assembly and Use

TCS-Cody 1/2

Electronic encoder-type lock for garage door drives

The TCS-Cody is a modern and safe alternative to traditional key switches. The

TCS-Cody can safely be used after two simple programming steps (master code

and pass code). For opening or closing of the door only a four- or ﬁve-digit nume-

ral code (pass code) has to be entered, which has been previously programmed via

the master code by an authorized person.

After correct input of the pass code and pushing the key button the drive is trigge-

red by the corresponding potential free relay contact.

The high ﬂexibility of the encoder is achieved by extensive programmability of the

individual operating functions. All sections required for operation are, however, pre-

programmed and thus immediately ready for use.

Technical Data:

24 V series 230 V series

Supply voltage 12 - 24 V AC / DC 230 V AC 50 Hz

Output 2x NO, NC relay contacts, 2x NO,NC relay contacts,

isolated, 8 A 250 V isolated, 8 A 250 V

Connections 2.5 mm2 max., 2.5 mm2max.,

Ambient- -20 ˚C to +60 ˚C -20 ˚C to +60 ˚C

temperature

Adaptation of the TCS-Cody 1/2 to special requirements:

The TCS-Cody 1/2 is provided with a series of ﬂexible time settings which allow the adapta-

tion to special cases of application. For programming these special operating modes please

ask for our ﬂow chart for the TCS-Cody series, if required!

geba GmbH is released of its obligations regarding guarantee and product liability if - without

prior permission - the unit has been modiﬁed, or if the installation is unproper or not in

accordance with our instruction manual.

The installer has to take care that the EMC-regulations are respected. GB

The most important characteristics of the TCS-Cody are:

Simple operation, programming and assembly.

Water-protected enclosure.

➢A maximum of safety:

➢ The electronic decoder is separately installed in the

protected area

➢ Up to 50 different pass codes can be stored

Up to 100 million different coding possibilities

Variable lock-out function

Nearly unlimited data security, even with power failure

➢ Special TIPTOMATIC-function for garage doors: After input of the pass

code the door can be stopped within the TIPTOMATIC time adjusted by

actuation of any key, and be closed or opened by repeated actuation

of any key.

➢ Two potential-free relay outputs

➢ High switching capacity for direct control of appliances

industial controls

Pro gr am 2

Clearing of a pass code

A pass code is cancelled by clearing of the corresponding memory

location (00-49)

In case of loss of the master code:

In case you forget the master code or the appliance has been accidently interfered with, there

is the possibility to reset the appliance by means of pressing the general reset button. This

means the appliance is brought back into the state preset by the factory.

Now the master code 12345678 preset by the factory as well as the pass code 1234 are valid

again. The appliance must now be re-programmed again.

Input 8-digit

master

code

Input of 2-digit

memory location,

e.g. 07 or 28

Sound

signal

2 x long

Sound

signal

1 x short

Sound

signal

1 x long

Push key

button

Push key

button

Push key

button

The memory location chosen is now cleared

Push key

button

Dear customer,

The Cody which you have purchased is one of our highest quality technical pro-

ducts. We have taken the greatest care in its manufacture to ensure that this

microprocessor controlled encoder reaches you in faultless condition. However in

the unusual event of suspected equipment failure please return the appliance

together with the enclosed warranty document to your dealer or direct to our

factory.

The extent of warranty exclusively refers to the free repair of malfunctions of the

appliance, which demonstrably are caused by faults in production or defective

material, inclusive of spare parts required for this purpose.

Therefore please ﬁrst read the instructions of use carefully before you start

programming!!!

WARRANTY-DOCUMENT

On the below described encoder we grant a warranty of

1 year

Type: TCS - Cody 1/2

Serial number: see label on logic PCB

Serial master code: All appliances are supplied with master code 12345678

Pass code: All appliances are supplied with pass code 1234 on memory location 01

Production date: ____________________________________________________

Sales date: ____________________________________________________

Dealers adress: ____________________________________________________

____________________________________________________

____________________________________________________ Reset to factory-settings:

Hold the GENERAL RESET BUTTON - after several short

sound signals a long sound signal can be heard (~ 5 sec.).

industial controls

Produkt Specifikationer

Mærke:	Geba Tronic
Kategori:	Garage døråbner
Model:	TCS - Cody 2

Har du brug for hjælp?

Hvis du har brug for hjælp til Geba Tronic TCS - Cody 2 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Garage døråbner Geba Tronic Manualer

Geba Tronic TCS - Cody - Light Manual

26 Januar 2023

Geba Tronic ROLLOTIMER Standard Manual

18 December 2022

Geba Tronic TCS - Cody 1- 1 Manual

7 December 2022

Geba Tronic DC2 ECO Manual

25 Oktober 2022

Geba Tronic DC 2 EN ECO Manual

22 Oktober 2022

Geba Tronic DC MiniMax 3 S Manual

21 Oktober 2022

Geba Tronic TCS - Cody 2 Manual

7 Oktober 2022

Garage døråbner Manualer

Nyeste Garage døråbner Manualer

Somfy Exavia Star Manual

1 Februar 2025

Chamberlain B4505TC Manual

14 November 2024

Schellenberg 60991 Manual

12 November 2024

Somfy Freevia 400 Manual

28 September 2024

Superrollo TA70 Manual

7 August 2024

LiftMaster 8500WMC-267 Manual

18 Maj 2024

Craftsman CMXZDCG498 Manual

25 Marts 2024

Chamberlain ML750-GB Manual

13 Marts 2024

Hormann ProMatic P Manual

14 Februar 2024

Chamberlain CIGCWC Manual

12 Januar 2024