Geemarc AMPLICALL PSA100 Manual

Geemarc Ikke kategoriseret AMPLICALL PSA100

Læs gratis den danske manual til Geemarc AMPLICALL PSA100 (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 17 personer og har en gennemsnitlig bedømmelse på 4.9 stjerner ud af 9 anmeldelser. Har du et spørgsmål om Geemarc AMPLICALL PSA100, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

The distance between both devices

cannot exceed 30 meters

AMPLICALL PSA 100

INSTALLATION

Fig. 1 Fig. 2 Fig. 3

Matière :

plastic PVC

2) Transmitter

1. Battery cover

2. Pessure sensor mat

Setting up the pressure sensor mat

1. Touch the edges of the pressure sensor mat until you

feel a hard piece of plastic, this is the small transmitter

that is inside. Open the opening that is kept shut by a

piece of double sided Velcro and get the transmitter out.

(Fig1)

2. Use a at screwdriver as a lever to open the battery

compartment. (Fig2)

3. Insert a coin cell battery CR2032 while observing the

correct polarity. (Fig.3)

4. Put the battery compartment back in place and make

sure the red LED light inside the transmitter lights up

when pressure is applied to the sensor mat.

5. Replace the transmitter in the opening on the edge of

the sensor mat before shutting it back with the piece of

double sided Velcro.

1. Unscrew the screw that is on the back of the wireless

receiver and that holds the cover of the battery

compartment in place before sliding open the battery

compartment. (Fig4)

2. Place three 1.5V batteries type LR14 (not included) in

the battery compartment while observing the correct

polarity, and place the battery compartment back in

place. (Fig5)

3. You can connect an AC adapter 6V DC 0.3A (not

included); plug length: 12mm; inside positive ID:

2.1mm; outside negative OD: 5.5mm) to the alert, and

install the batteries as backup in case of power failure.

Setting up the receiver

USING THE PSA100

PAIRING

TECHNICAL CHARACTERISTICS

(Fig 4)

(Fig 5)

The Amplicall PSA 100 is an easy-to-use device made up of

a pressure sensor mat connected to a signal transmitter, and

a wireless signal receiver.

As soon as pressure is being applied to the sensor mat, the

transmitter it is connected to will send a signal to the wireless

receiver which will immediately start ringing and ashing. The

receiver’s alarm volume can be set to high or low. The pressure

sensor mat can be placed in front of an entrance door or in a

corridor so that one can immediately be made aware of any

movement in the area.

The pressure sensor mat and wireless receiver are delivered

already paired. When setting them up for the rst time, you

should apply pressure on the sensor mat to make sure this

triggers the alarm, which ought to be placed less than 30

meters away.

Note: The receiver is wall mountable.

A. Drill two holes horizontally, 36 mm apart.

B. Insert two wall plugs xing into the two holes.

C. Screw two screws into the plugs, hang the receiver on the

support and slide it down to lock it.

1. Place the pressure sensor mat on a at surface.

2. If the power slide switch of the receiver is moved to the « CHIME

» position, the receiver will ring and ash once for 5 seconds

each time pressure is applied to the sensor mat.

3. If the power slide switch of the receiver is moved to the

« ALARM » position, the receiver will ring and ash once for 30

seconds each time pressure is applied to the sensor mat.

Note: The receiver will stop ringing and ashing if its power

slide switch is moved to the “OFF” position.

When not used, the power switch of the receiver should be moved

to the “OFF” position to prevent them from ringing and save battery

life.

You can pair up to 10 wireless receivers to a single pressure

sensor mat. To pair new receiver, you should follow the steps

below:

1.Move the receiver’s power slide switch to either the “ALARM” or

“CHIME” position. You will hear a tone. It indicates that the receiver

has been activated and is now in standby mode.

2. When in standby mode, you can use the tip of a pencil or a

screwdriver to press and hold the “learn” button that is on

the back of the wireless receiver for about 3 seconds. As

soon as you hear a short tone, you can release the “learn”

button. The wireless receiver is now in learning mode and

is ready to receive a pairing signal from your sensor mat’s

transmitter.

3. Move the power slide switch of your sensor mat’s transmitter

to either the “ALERT” or “ARM” position without applying

pressure to the mat.

4. If you hear four consecutive short tones coming from the

receiver, this means the pairing process has succeeded.

To unpair a wireless receiver, press and hold its “learn”

button for 12 seconds until you hear two long tones. This

indicates the receiver is no longer paired to any pressure

sensor mat.

Range: 30-meter

Frequency: 433.92Mhz

Ringer volume:

85dB (HI) or 70dB (LO) on the receiver

Power:

1 coin cell battery CR2032 for the transmitter

Three 1.5V batteries (type LR14) for the receiver

Up to 10 receivers for each transmitter

Radio frequency power: < 250mW

3 4

Pressure sensor mat and alarm

DESCRIPTION

Inside your gift box you should nd the below elements:

- 1 User guide

- 1 pressure sensor mat and its transmitter

- 1 wireless receiver( Batteries are not included) .

- A mains adapter is available as a spare part. (6V 0.3A)

Box Content

Wireless receiver

1. Volume control (HI/LO)

2,4. Visual indicators (Flash when

triggered by transmitter)

3. Visual indicator (Flashes when

triggered by transmitter/ Lights up

when batteries are low)

5. Loudspeaker

8. “Learn” paring button

9. Battery cover

10. Screw

11. Holes to mount device onto a wall

6. Power slide switch (Alarm/

o󰀨/chime)

7. DC adaptor socket

(6V DC/0.3A)

UGEnACPSA100

The middle LED (3) will start ashing to warn you that the battery

needs to be replaced.

Produkt Specifikationer

Mærke:	Geemarc
Kategori:	Ikke kategoriseret
Model:	AMPLICALL PSA100

Har du brug for hjælp?

Hvis du har brug for hjælp til Geemarc AMPLICALL PSA100 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Geemarc Manualer

Geemarc PhotoPhone 155 Manual

19 Juli 2025

Geemarc L2T-10 Manual

10 Juli 2025

Geemarc CL2000 Manual

5 Juli 2025

Geemarc SONARYA Manual

4 Februar 2025

Geemarc oCean400 Manual

11 December 2024

Geemarc CL8500 Manual

11 December 2024

Geemarc Clearsound CL64 Manual

11 December 2024

Geemarc CL555 Manual

11 December 2024

Geemarc AmpliDECT 260 Manual

10 December 2024

Geemarc CL8400BT Manual

10 December 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Slingshot Signature LE (2022) Manual

2 November 2025

Gymrex GR-MG51 Manual

2 November 2025

Hendi 975350 Manual

2 November 2025

SmallRig 4960 Manual

2 November 2025

Adventys GL 650 FLR Manual

2 November 2025

RADEMACHER RolloTron Schwenkwickler Comfort 1540 Manual

2 November 2025

Beverage-Air Horizon HFPS1HC-1S Manual

2 November 2025

Adventys DWIC 3000 Manual

2 November 2025

Homedics MD-1000-AU Manual

2 November 2025

Lantronix AP-GET-SFP-01 Manual

2 November 2025