GENERAL Life FH26S Manual

GENERAL Life Termostat FH26S

Læs gratis den danske manual til GENERAL Life FH26S (2 sider) i kategorien Termostat. Denne vejledning er vurderet som hjælpsom af 12 personer og har en gennemsnitlig bedømmelse på 4.5 stjerner ud af 6.5 anmeldelser. Har du et spørgsmål om GENERAL Life FH26S, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Cooling Mode

As soon as you energize your Room Thermostat, it will start working.

Your room thermostat takes the average room temperature of last 40

seconds as basis. If the ambient temperature rises above the

hysteresis positive temperature you set, your Room Thermostat will

start the cooling unit and if it drops below hysteresis negative

temperature value, will stop the cooling unit. Thus, it is ensured that

the ambient temperature remains within a certain range.

*External ﬂoor sensor is deactivated in the cooling mode.

ROOM THERMOSTAT HYSTERESIS NEGATIVE MENU

The hysteresis negative factory setting of your Room Thermostat is

-0.5°C. This value can be adjusted between “-0.1°C” and “-2.0°C”.

While the hysteresis negative value is -0.5°C, your Room Thermostat

will send a command to your heating unit when the room temperature

drops 0.5°C below the set temperature. For example, when we set the

Room Thermostat to 22.0°C, your heating unit will work when the

room temperature drops to 21.5°C. To change the hysteresis negative

setting

:While your device is off, press and hold the button for 3 seconds.

Press the button until the “ ” menu appears.

In the hysteresis negative menu, you can adjust the operating

sensitivity by turning the “ ” button to the right or left.

Press the button until the device turns off to save the settings and

exit.

The settings you have made have been saved. When you turn on

your device, it will work with the operating sensitivity you have set.

FLOOR SENSOR TEMPERATURE SETTING MENU

If a ﬂoor sensor is installed with Room Thermostat, only GENERAL

Life ﬂoor sensor should be installed. Otherwise, the product will be

out of warranty.

*In case of ﬂoor sensor connected, the following settings apply.

The factory temperature setting for ﬂoor sensor is 28°C. This value

can be adjusted between 23°C and 34°C. The ﬂoor sensor operating

sensitivity is 1°C. For example, when you set the ﬂoor sensor

temperature to 28°C, your Room Thermostat will stop the heating unit

from working when the ﬂoor temperature rises to 29°C. When the ﬂoor

temperature drops to 27°C, it starts the heating unit of the Room

Thermostat. To change the ﬂoor sensor temperature:

Press and hold the button for 3 seconds while your device is off.

Press the button until the “ ” menu appears.

Adjust the operating temperature by turning the “ ” button to the

right or left in the ﬂoor sensor temperature menu that appears.

Press the button until the device turns off to save the settings and

exit.

The settings you have made have been saved. When you turn on

your device, it will operate at the ﬂoor sensor temperature you have

set.

FACTORY RESET

You can reset the Room Thermostat to its factory default settings.

This action resets the calibration setting and hysteresis settings to

the factory setting. To factory reset your Room Thermostat:

While your device is off, press and hold the button for 3 seconds.

Press the button until the “ ” menu appears.

While in the “ ” menu, turn the button to the right or left, select the

“ ” option and press the button.

Your device will turn off and reset to factory settings.

ROOM THERMOSTAT WORKING PRINCIPLE

Heating Mode

As soon as you energize your Room Thermostat, it will start working.

Your room thermostat takes the average room temperature of last 40

seconds as basis. If the ambient temperature rises above the

hysteresis positive temperature you set, your Room Thermostat turns

off the heating unit, and if it drops below hysteresis negative

temperature value, it turns on the heating unit. Thus, it is ensured that

the ambient temperature remains within a certain range.

If the ﬂoor sensor measures temperature above 28°C, it turns off the

heating unit.*

*External ﬂoor sensor is only active when it is connected.

GENERAL SPECIFICATIONS

FH25/FH25S is a digital room thermostat designed for underﬂoor

heating and cooling system. The user can get more comfortable and

economic heating/cooling by adjusting the room thermostat with the

required temperature.

Sensitive Temperature Measurement Hysteresis Adjustment

Temperature Calibration ON/OFF Control

Wired connection

Floor sensor temperature setting

Heating/Cooling Modes

FH25/FH25S AND EQUIPMENTS

TECHNICAL DATA

ROOM THERMOSTAT

* External ﬂoor sensor is only active when it is connected.

Room Thermostat

85.7mm / 85.7mm / 33.5mm

230V AC

7A (240VAC – Resistive load)

10A (120VAC – Resistive load)

0.1 C

o o

(-2.0 C) – (+2.0 C)

o o

(5 C) – (30 C)

o o

(-10 C) – (+50 C)

o o

(-20 C) – (+60 C)

Dowels and

Screws

Dimensions ( H / L / W )

Operating Current

Relay NO Switching Current

Temperature Measurement

Accuracy

Operating Sensitivity

Operating Temperature Range

Operating Temperature

Storage Temperature

ENGLISH

generallife.com.tr

UNDERFLOOR HEATING THERMOSTAT

Room Temperature

Underﬂoor Heating Temperature*

Set Temperature

Heating Indicator

- If the Heating Indicator is blinking, the heating unit is

working.

- If the Heating Indicator lights up constantly, the heating

unit is not working.

Cooling Indicator

- If the Cooling Indicator is blinking, the cooling unit is

working.

- If the Cooling Indicator is steady, the cooling unit is not

working.

ROOM THERMOSTAT PLACEMENT

Place your Room Thermostat in a room you use frequently in your

living space. For example; like the hall or living room of your home.

Avoid installing the Room Thermostat in places where there is a lot of

air circulation, such as at the doorway or by the window. Also, do not

place it close to heating units (heater core, ﬁreplace, etc.) and in direct

sunlight. We recommend that the room thermostat is placed at a

height of 150 cm from the ﬂoor.

ROOM THERMOSTAT TEMPERATURE CALIBRATION

Temperature sensors used in Room Thermostats are very sensitive.

Based on the temperature on the thermometers in your living space

you need to calibrate your Room Thermostat. For this:

While your device is off, press and hold the button for 3 seconds.

 Press the button until you see the calibration menu that says “ ”

press it. The temperature difference you want from the calibration

menu, Adjust by turning the button to the right or left. This value can

be adjusted between “-8°C” and “+8°C”.

Press the button until the device turns off to save the settings and

exit.

Note: Recommended temperature calibration setting is “0.0 C”.

ROOM THERMOSTAT HEATING / COOLING MODES

Your Room Thermostat has heating and cooling modes. In order to

switch easily between heating and cooling modes:

While your device is turned off, press and hold the button for 3

seconds.

Press the button until the “ ” menu appears.

You can switch between “ ” (heating) and “ ” (cooling) modes

by turning the button to right or left in the “ ” menu.

To save the settings and exit, press the button until the device turns

off.

The settings you have made have been saved. Once you turned on

your device, it will operate with the changed settings.

ROOM THERMOSTAT HYSTERESIS POSITIVE MENU

The hysteresis positive factory setting of your Room Thermostat is

0.5°C. This value can be adjusted between “0.1°C” and “2.0°C”. While

the hysteresis positive value is 0.5°C, your Room Thermostat will

send a command to your heating unit when the room temperature

rises 0.5°C above the set temperature. For example, when we set the

Room Thermostat to 22.0°C, your heating unit will stop when the

room temperature rises to 22.5°C. To change the hysteresis positive

setting:

While your device is off, press and hold the button for 3 seconds.

“Press the button until the “ ” menu appears.

In the hysteresis positive menu, you can adjust the operating

sensitivity by turning the “ ” button to the right or left.

Press the button until the device turns off to save the settings and

exit.

The settings you have made have been saved. When you turn on

your device, it will work with the operating sensitivity you have set.

150 cm

min. 20 cm

Time

Heating

Unit Off

Heating

Unit On

Set

Temperature

Room

Temperature

22.0 C

22.5 C

21.5 C

Time

Cooling

Unit Off

Cooling

Unit On

Set

Temperature

Room

Temperature

22.0 C

22.5 C

21.5 C

FH25/FH25S USER MANUAL

SERIES:

MITRA, ADEN, ARUNA, CERES, GAIA, ILLONA, NORA, SENNA, TERRA,

THERMA

Produkt Specifikationer

Mærke:	GENERAL Life
Kategori:	Termostat
Model:	FH26S

Har du brug for hjælp?

Hvis du har brug for hjælp til GENERAL Life FH26S stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Termostat GENERAL Life Manualer

GENERAL Life NORA 270S Manual

25 September 2025

GENERAL Life HT11S Manual

25 September 2025

GENERAL Life FH10S Manual

31 August 2025

GENERAL Life FH25 Manual

29 August 2025

GENERAL Life HT260S Manual

22 August 2025

GENERAL Life HT230S Manual

22 August 2025

GENERAL Life HT250 Manual

21 August 2025

GENERAL Life HT390S Manual

24 Juli 2025

GENERAL Life HT440S Manual

24 Juli 2025

GENERAL Life HT301S Manual

23 Juli 2025

Termostat Manualer

Nyeste Termostat Manualer

Vimar 09474 Manual

25 December 2025

Fantini Cosmi EC18RL Manual

18 December 2025

Fantini Cosmi L23EM1B Manual

17 December 2025

Fantini Cosmi Intellicomfort CH141AK Manual

16 December 2025

Fantini Cosmi Intellicomfort CH141E Manual

16 December 2025

Essentials MATRIX Manual

2 December 2025

Honeywell CT62B Manual

1 December 2025

Honeywell X2P RTH20B Manual

28 November 2025

Honeywell RTH2CWF Manual

27 November 2025

Honeywell CT60A1036 Manual

27 November 2025