Golden Lighting Bijoux 1998-8SF Manual

Golden Lighting Lys Bijoux 1998-8SF

Læs gratis den danske manual til Golden Lighting Bijoux 1998-8SF (1 sider) i kategorien Lys. Denne vejledning er vurderet som hjælpsom af 7 personer og har en gennemsnitlig bedømmelse på 3.9 stjerner ud af 4 anmeldelser. Har du et spørgsmål om Golden Lighting Bijoux 1998-8SF, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/1

Assembly Instructions: (Bijoux)1998-8/8SF

IMPORTANT:

• ALL INSTALLATION WORK SHOULD BE DONE BY ACCREDITED PROFESSIONAL.

• SHUT OFF POWER SUPPLY AT FUSE OR CIRCUIT BREAKER!

• USE ONLY THE SPECIFIED BULBS. DO NOT EXCEED THE MAXIMUM WATTAGE!

PREPARING FOR INSTALLATION

Remove all of the contents from the carton. See the important notes

above. Remove the old xture from the ceiling, including the old

mounting strap.

1. Take the mounting strap assembly from the parts bag. One end of

nipple (F) should be attached to mounting strap (A) with washer and hex

nut (C) and (D) in place. Canopy loop (H) should be on the other end.

2. Use a screwdriver and mounting screws (B) to attach mounting strap

(A) to the junction box. (Note: When mounting strap (A) is properly

installed, about half of the exterior threads of nipple (F) are exposed,

allowingcanopyloop(H)totsnuglyontonipple(F).Youmaywantto

testtoensurethatwithcanopy(G)inplace,canopyloop(H)tsonto

nipple (F). After testing, remove everything from the nipple and place

aside for later.) until the desired height is reached.

CLEANING TIPS

Treat the xture gently! Regular cleaning will reduce the need for deep cleaning. For regular cleaning, turn off the light and wipe down the

xture with a clean lint-free cotton or microber cloth. Never spray cleaner directly onto the xture.

For Customer Service, please

contact the place of purchase.

FINISHING THE INSTALLATION

6. Push canopy (G) up to the ceiling and slide canopy loop collar (I) up beneath the canopy. Tightly thread canopy loop collar (I) onto

canopy loop (H) to secure canopy (G) in place.

7.Slidecandlesleeves(O)overthesockets.Installlightbulbsinaccordancewiththexture’sspecications.Donotexceedthemaximum

wattage.

8.Yourinstallationisnowcomplete.Turnonthepowerandtestthexture.

3.Placeshade(N)ontoaatsurface.Threadtoploop(L)ontopost

(M). Measure to determine the correct number of chain links (J) needed

for proper hanging height. If necessary, use a pair of pliers to open and

remove any excess chain. For the semi-ush installation, thread the wires

through canopy (G). Open one of chain connectors (K) and use it to connect

directly top loop (L) to canopy loop (H).

CONNECTING THE WIRES

5.Haveanassistantsupportthexture’sweightwhilecompletingthewiring.Cut

awaytheexcesswires.Threadthexture’swiresthroughthecanopyloopand

nipple.Refertothewiringdiagramandattachthexture’swirestothepower

supply wires from the junction box. Connect Hot to Hot, Neutral to Neutral, and

Ground to Ground. Twist the ends of the wire pairs together, and then twist on

a wire connector. Make sure all twists are in the same direction. If there is no

house ground wire coming from the junction box, locate ground screw (E) on

themountingbracket/mountingstrapandwrapthexture’sgroundwirearound

the ground screw. Use a screwdriver to tighten the top of ground screw (E) onto

the wires and into the mounting bracket/mounting strap. Tuck the wires into the

junction box.

How to Identify the Fixture’s Wires

Hot Neutral Ground

Smooth

Ribbed

Bare Metal,

Green, or

Green Inner

Thread

Black

White

Black Inner

Thread

White Inner

Thread

House Wires

Fixture Wires

Hot

4. Attach one of chain connector (K) to each end of chain (J). Use one of chain connectors (K) to attach chain (J) to top loop (L) and close

thechainconnector.Feedthexture’swiresupthroughthechain(everythreelinksorso),pullingthewiresuntiltaut.Slidecanopyloop

collar (I) and canopy (G) onto the chain and wires. Use the free chain connector (K) to attach chain (J) to canopy loop (H).

Produkt Specifikationer

Mærke:	Golden Lighting
Kategori:	Lys
Model:	Bijoux 1998-8SF

Har du brug for hjælp?

Hvis du har brug for hjælp til Golden Lighting Bijoux 1998-8SF stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Lys Golden Lighting Manualer

Golden Lighting Bijoux 1998-5SF Manual

14 November 2025

Golden Lighting Monroe 7041-SF Manual

14 November 2025

Golden Lighting Waverly 3500-1W AB Manual

14 November 2025

Golden Lighting Aenon 3164-3P Manual

13 November 2025

Golden Lighting Monroe 7041-9 Manual

10 November 2025

Golden Lighting Aenon 3164-LP Manual

9 November 2025

Golden Lighting Adeline 1088-SF Manual

9 November 2025

Golden Lighting Cassio 2086-4SF Manual

9 November 2025

Golden Lighting Dixon 3219-SF Manual

8 November 2025

Golden Lighting Ellie 6808-6SF Manual

8 November 2025

Lys Manualer

Nyeste Lys Manualer

NightStick TWM-852XL Manual

17 December 2025

17 December 2025

17 December 2025

17 December 2025

17 December 2025

17 December 2025

17 December 2025

17 December 2025

17 December 2025

Vaxcel VL55602 Manual

16 December 2025