Golden Lighting Payton 1157-6P Manual

Golden Lighting Lys Payton 1157-6P

Læs gratis den danske manual til Golden Lighting Payton 1157-6P (1 sider) i kategorien Lys. Denne vejledning er vurderet som hjælpsom af 12 personer og har en gennemsnitlig bedømmelse på 4.4 stjerner ud af 6.5 anmeldelser. Har du et spørgsmål om Golden Lighting Payton 1157-6P, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/1

Assembly Instructions: (Payton)1157-4P/6P

IMPORTANT:

• ALL INSTALLATION WORK SHOULD BE DONE BY ACCREDITED PROFESSIONAL.

• SHUT OFF POWER SUPPLY AT FUSE OR CIRCUIT BREAKER!

• USE ONLY THE SPECIFIED BULBS. DO NOT EXCEED THE MAXIMUM WATTAGE!

CLEANING TIPS

Treat the xture gently! Regular cleaning will reduce the need for deep cleaning. For regular cleaning, turn off the light and wipe down the

xture with a clean lint-free cotton or microber cloth. Never spray cleaner directly onto the xture. Dry with a lint-free or microber cloth.

For Customer Service, contact

the place of purchase

Smooth / Black /

Transparent (L)

Black (Hot)

Ribbed / White /

Transparent (N)

Bare Copper / Transparent with

Green Interior / Green

White (Neutral)

Green

(Ground)

PREPARING FOR INSTALLATION

Carefully remove all of the contents from the carton. See the important notes above.

Shutoffthepoweratthecircuitbreakerandcompletelyremovetheoldxturefromthe

ceiling, including the old mounting strap.

From the parts bag remove the mounting strap assembly. One end of nipple (F) should

beattachedtomountingstrap(A)withhexnuts(C,D)inplace.Theotherendshould

have canopy loop (H) attached. Match the threaded holes of mounting strap (A) to the

spacingoftheholesonthejunctionbox.Attachmountingstrap(A)tothejunctionbox

using mounting screws (B) and a screwdriver. Tighten securely. Unscrew canopy loop

collar (I) from canopy loop (H). Pass canopy (G) over the mounted canopy loop to test

theheight.Approximatelyhalfofthecanopyloop’sexteriorthreadsshouldbeexposed,

andthecanopyloopcollarshouldtsnuglyontothecanopyloop.Removecanopy

(G) and adjust the height of nipple (F) and canopy loop (H) until the desired height is

reached.

ASSEMBLING THE FIXTURE

Rod(P)andtopassembly(Q),withtoploop(L)areonthexture’swires.Pullthewires

untiltaut.Screwrod(P)intothecenterofxturebody(O)andthentoploop(L)onto

the threads of top assembly (Q). By measuring, determine the correct number of chain

links needed for proper hanging height. If necessary, use a pair of pliers to open and

removeanyexcesschain.Attachonechainconnector(K)toeachendofchain(J).Use

onechainconnector(K)toattachchain(J)totoploop(L)andclosethechainconnector.

Feedthexture’swiresupthroughthechain(everythreelinksorso),pullingthewires

until taut. Slide canopy loop collar (H) and canopy (G) onto the chain and wires. Use the

freechainconnector(K)toattachchain(J)tocanopyloop(H).

CONNECTING THE WIRES

Haveanassistantsupportthexture’sweightwhilecompletingthewiring.Cutaway

excesswire.Threadthexture’swiresthroughcanopyloopandnipple.Attachthe

xture’swirestothepowersupplywiresfromthejunctionbox.Connectblackto

smooth/black/transparent (L) wire; white to ribbed/white/transparent (N) wire; ground to

ground (green or copper). Twist the ends of the wire pairs together, and then twist on a

wire connector. Make sure all twists are in the same direction. If there is no ground wire

(greenorcopper)fromthejunctionbox,locategroundscrew(E)onmountingstrap(A)

andwrapthexturegroundwirearoundthegreengroundscrew(E).Useascrewdriver

to secure ground screw (E) onto the mounting bracket/mounting strap. Tuck all wires.

FINISHING THE INSTALLATION

Push canopy (G) up to the ceiling and slide canopy loop collar (I) up beneath the canopy. Tightly thread canopy loop collar (I) onto canopy

loop (H) to secure canopy (G) in place.

Notes: Glass edges may be sharp. Wear gloves for installation to avoid injury. Have an assistant help throughout this process.

Use deco nuts (S) to attach bottom rim (T) to metal frame (N). Carefully slide glass panels (U) into metal frame (N). Lower the other top

rim (T) over metal frame (N). Place iron bar (R) against the glass and secure in place with decorative screws (V). If the glass can not be

successfullyplacedintotheframework,pleaseadjustironbar(R).Yourinstallationisnowcomplete.Turnonthepowerandtestthexture.

Installbulbs(notincluded)inaccordancewiththexture’sspecications.Donotexceedthemaximumwattage.Withthehelpofyour

assistant, carefully raise the glass and metal cage assembly up to top assembly (Q) and attach the metal cage assembly to the top

assembly using decorative nuts (M).

Yourinstallationisnowcomplete.Turnonthepowerandtestthexture.

Produkt Specifikationer

Mærke:	Golden Lighting
Kategori:	Lys
Model:	Payton 1157-6P

Har du brug for hjælp?

Hvis du har brug for hjælp til Golden Lighting Payton 1157-6P stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Lys Golden Lighting Manualer

Golden Lighting Bijoux 1998-5SF Manual

14 November 2025

Golden Lighting Monroe 7041-SF Manual

14 November 2025

Golden Lighting Waverly 3500-1W AB Manual

14 November 2025

Golden Lighting Aenon 3164-3P Manual

13 November 2025

Golden Lighting Monroe 7041-9 Manual

10 November 2025

Golden Lighting Aenon 3164-LP Manual

9 November 2025

Golden Lighting Adeline 1088-SF Manual

9 November 2025

Golden Lighting Cassio 2086-4SF Manual

9 November 2025

Golden Lighting Dixon 3219-SF Manual

8 November 2025

Golden Lighting Ellie 6808-6SF Manual

8 November 2025

Lys Manualer

Nyeste Lys Manualer

NightStick TWM-852XL Manual

17 December 2025

17 December 2025

17 December 2025

17 December 2025

17 December 2025

17 December 2025

17 December 2025

17 December 2025

17 December 2025

Vaxcel VL55602 Manual

16 December 2025