Golden Lighting Torbellino 8106-D5 CDB Manual

Golden Lighting lampe Torbellino 8106-D5 CDB

Læs gratis den danske manual til Golden Lighting Torbellino 8106-D5 CDB (3 sider) i kategorien lampe. Denne vejledning er vurderet som hjælpsom af 25 personer og har en gennemsnitlig bedømmelse på 4.9 stjerner ud af 13 anmeldelser. Har du et spørgsmål om Golden Lighting Torbellino 8106-D5 CDB, eller vil du spørge andre brugere om produktet?

Side 1/3
Canopy
1ea
Mounting
Screws 2ea Top loop 1ea
Chain 6ft Threaded ring 1ea Wire connectors 2ea
Chain connector 2ea Canopy loop 1ea Nipple 1ea
Mounting Strap 1ea Hex Nut 1ea Finial 1ea
Part Needed Quantity
Part Needed Quantity
Reason why ( missing, scratched, broken glass, bent, bad nish)
Comments
F A IIXTURE SSEMBLY NSTRUCTIONS
For Customer Service, contact the place of purchase to arrange for replacement parts.
NOTE: INSTALL THE GLASS ASSEMBLY
AFTER THE FIXTURE IS HUNG.
1. Feed the xture wires through the Top loop (J)
and pull the wires until taut.
2.Then screw the Top Loop (J) to the top of Frame
(K) until tight.
8106-D5 CDB
Read and review installation instruction sheet before
assembling the xture.
Fig 1
Notice: Please review the parts listing and check for all parts before assembling the xture. If any parts are
missing or damaged, please note onthis sheet and contact the place of purchase to arrange for
replacement parts.
PARTS LIST Company Name:_______________________Co. Account #:_____________
to be lled out by retailer
PARTS & ASSEMBLY SHEET
This xture assembled PO:__________ Date: ________
Fixture Name: Torbellino 8106-D5 CDB
K
CHAIN
J
H
For Customer Service, contact the place of purchase to arrange for replacement parts.
8. By measuring determine correct number of links
needed for proper hanging height. Use a pair of
pliers to open one link of the Chain (C2) then
remove the excess Chain (C2) and discard it.
9. Use one chain connector(E2) to attach one end
of the chain to the Top loop (D2) and close the
chain connector.
10. Feed the xture wires through the Chain (every
three links) and pull the wires until taut.
11. Slip Canopy loop collar (B2) over the chain,
then do the same with the canopy (F2).
12. When ready to complete the installation Use the
other chain connector and attach the other end of
the chain to the canopy loop (A2) and close the
chain connector.
13. Make sure the weight of the chandelier is
supported by the chain-not the electrical wire.
* You may now install the xture.
Fig 3
3. Unscrew two of the Deco screws (L) from the
Frame (K) and save.
4. Two arms are already attached to the Frame.
Gently spread the arms until evenly spaced.
5. Align the hole in lower side of Frame arm (K) with
hole Frame(K). Secure in place with the Deco
screw (L).
6. Repeat with remaining arms and Deco screws.
* NOTE: The Finial can be scratched or broken if
the full weight of the xture is placed on it. To avoid
damage attach Finial after hanging the xture.
7. Attach Finial (N) to the base of xture Frame (K)
by threading the Finia l(N) onto the threaded rod
(M) until tight.
Fig 2
PARTS & ASSEMBLY SHEET
Fixture Name: Torbellino 8106-D5 CDB
Note: Complete these remaining steps after the
xture is hung.
14. Place the Glass Shade (P) over the Threaded
Socket (O),place the Socket washer (Q) over the
threaded socket (O) then secure the Glass Shade
(P) by threading by the Socket Ring (R) until tight.
15. Install the light bulbs in accordance with the
xture's specications.
(DO NOT EXCEED THE MAXIMUM WATTAGE RATING)
Fig 4
B2
A2
C2
E2
D2
E2
O
Q
P
K
M
N
L
CHAIN
J
O
Q
R
P
M
L


Produkt Specifikationer

Mærke: Golden Lighting
Kategori: lampe
Model: Torbellino 8106-D5 CDB

Har du brug for hjælp?

Hvis du har brug for hjælp til Golden Lighting Torbellino 8106-D5 CDB stil et spørgsmål nedenfor, og andre brugere vil svare dig