Harman Kardon Enchant Manual
Harman Kardon
Subwoofer
Enchant
Læs gratis den danske manual til Harman Kardon Enchant (44 sider) i kategorien Subwoofer. Denne vejledning er vurderet som hjælpsom af 38 personer og har en gennemsnitlig bedømmelse på 4.8 stjerner ud af 19.5 anmeldelser. Har du et spørgsmål om Harman Kardon Enchant, eller vil du spørge andre brugere om produktet?
Side 1/44
OWNER’S
MANUAL
ENCHANT 1300
ENCHANT 800
ENCHANT SUBWOOFER
2
/
IMPORTANT SAFETY
INSTRUCTIONS
Verify Line Voltage Before Use
The Enchant soundbars have been designed for use with 100-
240 volt, 50/60 Hz AC current. Connection to a line voltage
other than that for which your product is intended can create
a safety and re hazard and may damage the unit. If you have
any questions about the voltage requirements for your specic
model or about the line voltage in your area, contact your
selling dealer before plugging the unit in to a wall outlet.
Do Not Use Extension Cords
To avoid safety hazards, use only the power cord supplied
with your unit. We do not recommend that extension cords be
used with this product. As with all electrical devices, do not run
power cords under rugs or carpets, or place heavy objects on
them. Damaged power cords should be replaced immediately
by an authorized service center with a cord that meets factory
specications.
Handle the AC Power Cord Gently
When disconnecting the power cord from an AC outlet, always
pull the plug; never pull the cord. If you do not intend to use
your speaker for any considerable length of time, disconnect
the plug from the AC outlet.
Do Not Open the Cabinet
There are no user-serviceable components inside this product.
Opening the cabinet may present a shock hazard, and any
modication to the product will void your warranty. If water
accidentally falls inside the unit, disconnect it from the AC
power source immediately, and consult an authorized service
center.
3
/
TABLE OF CONTENTS
/ IMPORTANT SAFETY INSTRUCTIONS 2 .............................................
/ INTRODUCTION ....................................................................................... 4
/ WHAT’S IN THE BOX 5 ...............................................................................
/ PRODUCT OVERVIEW .............................................................................7
/ INSTALLATION ..........................................................................................15
/ CONNECTING TO YOUR TV ............................................................... 19
/ CONNECTING TO OTHER DEVICES ...............................................21
/ CONNECTING TO POWER ................................................................23
/ CONNECTING TO WI-FI .......................................................................27
/ USING YOUR SOUNDBAR ..................................................................28
/ SET TI N GS...................................................................................................32
/ UPDATE SOFTWARE .............................................................................35
/ SPECIFIC ATIONS .....................................................................................36
/ TROUBLESHOOTIN G ........................................................................... 40
/ OPEN SOURCE LICENSE NOTICE ...................................................42
/ LI C EN SE ......................................................................................................43
4
/
INTRODUCTION
This manual includes information of the Enchant 1300, Enchant
800 and Enchant Subwoofer. We encourage you to take a few
minutes to read this manual, which describes the products and
includes step-by-step instructions to help you set up and get
started. Read and understand all the safety instructions before
using your product.
This product may have an important software update
available. Please follow the instructions to connect the
product to Wi-Fi to ensure that your product has the most
recent software updates.
Design and specications are subject to change without notice.
If you have any questions about these products, their
installation or their operation, please contact your
Harman Kardon retailer or customer service, or visit us at
www.harmankardon.com
5
/
WHAT’S IN THE BOX
Carefully unpack the box and check if the following parts are
included. If any part is damaged, do not use it, contact your
Harman Kardon retailer or customer service.
ENCHANT 1300 / ENCHANT 800
1. Main unit
2. Power cord*
3. HDMI cable
4. AUX cable
5. Optical cable
6. Remote control (with 2 AAA batteries)
7. Wall-mount brackets
* Power cord quantity and plug type vary by regions.
VOL
1
2 3 4 5 6
7
/ W H A T ’ S I N T H E B O X
6
Inserting Batteries before using the Remote
Control (AAA batteries X 2)
Slide the battery cover in the direction of the arrow until it is
completely removed. Insert 2 AAA batteries (1.5V) oriented so
that their polarity is correct. Slide the battery cover back into
position.
ENCHANT SUBWOOFER (Optional)
1. Main unit
2. Power cord*
* Power cord quantity and plug type vary by regions.
1 2
7
/
PRODUCT
OVERVIEW
Front Panel & Top Panel of the Soundbar
1. + / - (Volume)
• Adjust the volume level.
• Press both simultaneously to mute the soundbar.
2. (Power)
• Turn the power on or to standby.
• Press and hold for 5 seconds to reset the soundbar
Wi-Fi settings.
3. Display panel
• Display the current mode and status.
1
2
3
4
/ P R O D U C T O V E R V I E W
8
4. (Source)
• Select the source input mode:
Source Input Mode Display
HDMI OUT (TV ARC) TV ARC
HDMI 1 input HDMI 1
HDMI 2 input* HDMI 2
HDMI 3 input* HDMI 3
Optical input OPT
Aux input AUX
Bluetooth input BT
USB input USB
* HDMI 2 and HDMI 3 are available on the Enchant 1300
only.
/ P R O D U C T O V E R V I E W
9
Back Panel of the Soundbar
ENCHANT 1300
ENCHANT 1300
1. AC IN
• Connect to the power cord, then connect the power
cord to a wall outlet.
2. AUX IN
• Connect to the Analog output of an external audio
device.
3. USB
• Connect to a USB storage device to play music.
1 3 52 4 6 7
1 2 5 3 47 6
/ P R O D U C T O V E R V I E W
10
4. OPTICAL
• Connect to the optical audio output on your TV or
digital device.
5. SUBWOOFER PAIRING
• Press to enter the subwoofer pairing mode.
• Press and hold to disconnect and re-enter the
subwoofer pairing mode.
6. HDMI 1 / HDMI 2* / HDMI 3*
• Input digital video and audio signals simultaneously
using an HDMI cable.
• Connect to the HDMI output on a digital device.
7. HDMI OUT (TV ARC)
• Connect to the HDMI (ARC) input on your TV.
* HDMI 2 and HDMI 3 are available on the Enchant 1300 only.
/ P R O D U C T O V E R V I E W
11
Back Panel of the Subwoofer
1. PAIRING
• Press to pair the subwoofer with the Enchant soundbar.
2. AC IN
• Connect to the power cord, then connect the power
cord to a wall outlet.
1
2
/ P R O D U C T O V E R V I E W
12
Remote Control
VOL
15
14
13
12
11
1
2
4
5
6
7
8
9
10
3
1. (Power)
• Power on or switch to standby.
2. DIM LEVEL
• Set the brightness of the display
panel.
3. PRESETS
• Recall preset audio settings and
SOUND MODE. To save a
preset:
• Press the button SOURCE
to select a source.
• Press the SOUND MODE
button to select a preferred
setting for that source.
• , Adjust the VOLUME BASS
and NIGHT MODE to your
preference.
• Press and hold any PRESET
button for 3 seconds to save
all soundbar settings as a
preset. Press any PRESET
button to recall all of the audio
settings.
4. MUTE
• Mute or unmute the soundbar
audio.
5. VOL + / -
• Increase or decrease the volume
level.
/ P R O D U C T O V E R V I E W
13
6. SOUND MODE
• Select preset sound modes
to suit your music or video:
STANDARD / MUSIC / MOVIE /
VOICE / PERSONAL.
• Select the STANDARD mode
to enjoy the original sound with
MultiBeam Surround Sound.
• Select the MUSIC mode to
enjoy music sound with a light
MultiBeam Surround Sound
eect.
• Select the MOVIE mode to enjoy
movie sound with MultiBeam
Surround Sound.
• Select the VOICE mode to
enhance dialogue with a light
MultiBeam Surround Sound
eect.
• Select the PERSONAL mode
to enjoy the original sound with
MultiBeam Surround Sound. The
bass setting can be changed to
a personal preference and saved
in the preset.
• Press and hold for 5 seconds to
reset the default audio settings.
7. /
• Skip to the previous or next track
for Chromecast, Bluetooth or
USB playback.
8. SHUFFLE
• Repeat or shue play (USB
playback only).
9. BASS - / +
• Decrease or increase the bass
level of the soundbar (or the
subwoofer once successfully
paired).
10. AUDIO SYNC - / +
• Decrease or increase audio sync
delay if the video and audio
synchronization is not correct.
11. NIGHT MODE
• Turn the night mode (Dynamic
Range Control) on or o for
Dolby Digital and DTS tracks.
With the night mode turned
on, loud sound is reduced (the
sound may be distorted).
12.
• Play or pause Chromecast,
Bluetooth or USB playback.
13. BT
• Press to enter Bluetooth pairing
mode.
• Press and hold for 5 seconds to
connect with a new device.
14. SOURCE
• Select an input source for the
soundbar: HDMI ARC/ HDMI 1
/ HDMI 2* / HDMI 3* / Optical /
AUX / USB / BT.
/ P R O D U C T O V E R V I E W
14
15. CALIBRATION
• Press and hold for 3 seconds to initiate Automatic
MultiBeam Calibration. (see calibration section)
* HDMI 2 and HDMI 3 are available on the Enchant 1300 only.
15
/
INSTALLATION
Place the Soundbar below your TV on the
Table
NOTES:
• Remove any interference from both sides of the soundbar so the
side-ring speakers can operate correctly and reect sound in
your room. Blocking the side horns aects acoustic performance.
• To avoid wireless interference, keep other wireless devices 1-3 ft
(0.3-0.9 m) away from the soundbar.
• Make sure there is an AC outlet nearby.
Place the soundbar on its rubber feet on a stable and level
surface below your TV.
CAUTION:
• Do not place the soundbar on its front, back or top when in use.
• Do not place any objects on top of the soundbar.
TV
/ I N S T A L L A T I O N
16
Wall-mount the Soundbar
CAUTION:
• Before mounting on a wall, make sure the wall can support the
weight of this unit.
• Install on a vertical wall only.
• For the wall-mounting, avoid a location with high temperature or
humidity.
• Connect cables from the unit to external devices before installing
on the wall.
• Make sure the unit is powered o and unplugged before the
installation. Otherwise, it may cause an electric shock.
• Purchase and use the xing screws or anchors appropriate for
the type of wall you have (plasterboard, iron board, wood, etc.).
If possible, x the support screws into wall studs.(Diameter: M5;
Length: 1.5 inches or longer recommended)
1) Use tape to stick the wall-mounted paper guide on the wall,
push a pen tip through the center to mark the wall-mounted
bracket location and remove the paper.
TV
WALLMOUNTED PAPER GUIDE
/ I N S T A L L A T I O N
17
2) Use an appropriately sized drill bit, drill a hole in the wall at
each marking. Using the appropriate anchors, screw the wall
mount brackets into the support screw holes in the wall.
x3
CAUTION:
• If the markings do not correspond to the positions of studs, make
sure to insert appropriate anchors or mollies into the holes before
inserting the support screws. If you use anchors or mollies, make
sure the holes you drill are large enough for the anchors or mollies
you use.
3) With the supplied small screws, x the L-Brackets to the
bottom of the soundbar.
/ I N S T A L L A T I O N
18
4) Hook the soundbar to the brackets attached to the wall.
CAUTION:
• Do not connect the power cord of the soundbar or your TV
to a wall outlet until all connections between components are
complete.
• Before moving or installing the unit, make sure to power o and
unplug rst.
TV
19
/
CONNECTING TO
YOUR TV
NOTES:
• If you want to enjoy sound only from the soundbar, make sure
to set your TV audio settings to support external speakers and
disable the built-in TV speakers.
• Before you make or change any connections, make sure that all
devices are disconnected from the power outlet.
Connect to your TV with an HDMI Cable
(Preferred)
1) Connect the supplied HDMI cable from the
HDMI OUT (TV ARC) connector on the back of the
soundbar to the HDMI IN (ARC) connector on your TV.
2) Press the button on the top panel of the soundbar or the
SOURCE button on the remote control to select the TV
ARC mode.
ENCHANT 1300
ENCHANT 800
HDMI (ARC)
HDMI OUT
(TV ARC)
TV
/ C O N N E C T I N G T O Y O U R T V
20
NOTES:
• An HDMI connection supports digital audio and video with a
single connector. It is the best option to connect to your soundbar.
• If your TV features an HDMI ARC connector, you can hear the TV
audio through your soundbar by using a single HDMI cable.
• This HDMI connection is required if you intend to connect other
video devices to the soundbar inputs to display on your TV.
• On your TV, turn on HDMI-CEC operations. HDMI-CEC is a feature
that enables CEC compliant devices that are connected through
HDMI to be controlled by a single remote control, such as volume
control for both the TV and the soundbar. See the user manual of
your TV for details.
Connect to your TV with an Optical (Digital) Cable
NOTES:
• Make sure you have removed the protective cap from both ends
of the optical cable.
1) Connect the connector on the soundbar to OPTICAL IN
the OPTICAL OUT connector of your TV with the provided
digital optical cable.
2) Press the button on the top panel of the soundbar or
the SOURCE button on the remote control to select the
OPTICAL mode.
ENCHANT 1300
ENCHANT 800
OPTICAL OUT
TV
OPTICAL IN
21
/
CONNECTING TO
OTHER DEVICES
HDMI Cable (Preferred)
Connect a digital device such as a set-top box, DVD/Blu-ray
player, or games console to your soundbar through a single
HDMI connection.
1) Connect the HDMI cable from the HDMI IN jack on the
back of the soundbar to the HDMI OUT jack on your digital
device.
2) Press the button on the top panel of the soundbar or
the SOURCE button on the remote control to select the
HDMI mode.
NOTES:
• For the best performance, always use a High-Speed (type 2)
HDMI cable. See your HDMI cable specications for more details.
ENCHANT 1300
ENCHANT 800
HDMI OUT
HDMI 2HDMI 1 HDMI 3
/ C O N N E C T I N G T O O T H E R D E V I C E S
22
Optical or Analog Audio Cables
1) Connect the OPTICAL or connector on the soundbar AUX
to the jack of the source OPTICAL OUT or AUDIO OUT
device by using the provided optical cable or 3.5mm audio
cable.
2) Press the button on the top panel of the soundbar or
the SOURCE button on the remote control to select the
OPTICAL or AUX mode.
OPTICAL IN
ENCHANT 1300
ENCHANT 800
AUX-IN
AUX-OUT
OPTICAL OUT
23
/
CONNECTING TO
POWER
Power On the Soundbar
NOTES:
• Before connecting the power cord, make sure all other
connections have been completed.
• The (Power) button will begin working in 4 to 6 seconds after
plugging in the AC power cord.
• When you disconnect the power cord, always pull the plug, never
the cable.
• Do not connect this unit or other components to an AC outlet until
all connections between components are complete.
1) Plug one end of the power cord into the AC IN connector
on the back of the soundbar.
ENCHANT 1300
ENCHANT 800
1
2
/ C O N N E C T I N G T O P O W E R
24
2) Plug the other end of the power cord into a live AC (mains)
wall socket.
• “LOADING” scrolls on the display panel. The soundbar
will take about 30 seconds to load, then enter standby
mode and ready for use.
3) Slide the battery compartment cover until it is completely
removed. Insert the two provided AAA 1.5V batteries
with correct polarity orientation. Slide the cover back into
position.
4) Press to power on the soundbar.(Power)
• “ON” is displayed.
Power On the Subwoofer (Optional)
1) Plug one end of the power cord into the AC IN connector
on the back of the subwoofer.
2) Plug the other end of the power cord into a live AC (mains)
outlet.
/ C O N N E C T I N G T O P O W E R
25
Connect the Subwoofer (Optional)
1) Power on both the soundbar and the subwoofer.
2) Press the SUBWOOFER PAIRING button on the soundbar
or PAIRING button on the subwoofer to enter pairing mode.
• “SUB PAIRING” will be displayed. You will hear a pairing
chime once connected and “SUB PAIRED” will be
displayed.
Subwoofer LED behavior
• White (Flashing slowly): Powered on
• White (Flashing fast): Pairing
• White (Solid): Paired
ENCHANT 1300
ENCHANT 800
/ C O N N E C T I N G T O P O W E R
26
NOTES:
• If the soundbar is powered o, the subwoofer will enter standby
mode.
• If you use a device that uses the same frequency (2.4GHz) as
the soundbar near your soundbar, interference may cause some
sound interruption.
• The maximum transmission distance of the wireless signal
between the soundbar and the subwoofer may vary depending on
your operating environment.
27
/
CONNECTING TO
WI-FI
The soundbar is connected to Wi-Fi with the Google Home
app.
1) Download the Google Home app.
2) Power on the soundbar.
3) Open the Google Home app and set up your soundbar as
instructed in the app. Always follow the instructions in the
app to complete the Wi-Fi setup.
4) Sign in with your Google account. If you do not have, create
a new one.
NOTES:
• If you encounter any setup issues, make sure to enable Bluetooth
and location services on your smartphone or tablet.
• Once the soundbar is connected to the Internet for the rst time,
it may detect a software update to improve performance. This
update may take a few minutes to complete.
• In the Google Home app, you can rename the soundbar. The
device name will remain during Bluetooth device discovery and
Google Cast streaming.
• Once the soundbar is connected to Wi-Fi, it will receive a periodic
over-the-air software update to improve performance.
• To disconnect from the Wi-Fi router and reset the soundbar Wi-
Fi settingsrst turn the soundbar on, then press and hold the
button on the soundbar top panel for 5 seconds.
HK ENCHANT 1300
HK ENCHANT 800
1
2 3
28
/
USING YOUR
SOUNDBAR
Play Music with Google Cast
With Chromecast built into your Enchant soundbar, you can
stream music, podcasts, and playlists from 300+ music apps to
your soundbar by simply tapping the Cast button.
1) Open any Chromecast-compatible app on your smartphone
or tablet.
2) Tap the icon on the app and select the Enchant
soundbar.
3) Press “Play” on the app.
NOTES:
• The name of your soundbar is assigned during the Wi-Fi setup.
• Use the Google Home app to group the soundbar and other
Chromecast audio devices together for multi-room music
throughout your home.
• The soundbar can support audio streaming and cannot support
video streaming.
Play Music through Bluetooth
1) button on the remote control to enter Bluetooth Press BT
pairing mode. Alternatively, repeatedly press SOURCE
until “BT” appears on the display panel.
VOL
PAIRING
/ U S I N G Y O U R S O U N D B A R
29
2) Choose “HK ENCHANT 1300/800” to connect.
• When the music is streamed, the track, title and artist of
the song will scroll on the display panel.
NOTES:
• If you have already connected the soundbar to Wi-Fi and changed
the device name, then select the new device name.
• If asked for a PIN code when connecting a Bluetooth device, enter
“0000”.
• To exit Bluetooth mode, choose other sources.
• To disconnect and pair another device, press and hold BT on
the remote control for 5 seconds.
• The soundbar automatically turns o after 10 minutes of inactivity.
• Bluetooth performance can be aected by the distance from your
device to the soundbar and environment of operation.
• Keep a distance of less than 10m/33ft between the soundbar and
your Bluetooth device to avoid disconnection.
Play Music from USB Storage Device
Play music les located on USB storage devices through the
soundbar.
1) Plug your USB storage device into the USB socket of the
soundbar.
HK ENCHANT 1300
HK ENCHANT 800
CONNECTED
Produkt Specifikationer
| Mærke: | Harman Kardon |
| Kategori: | Subwoofer |
| Model: | Enchant |
Har du brug for hjælp?
Hvis du har brug for hjælp til Harman Kardon Enchant stil et spørgsmål nedenfor, og andre brugere vil svare dig
Subwoofer Harman Kardon Manualer
18 Juli 2024
28 November 2022
Subwoofer Manualer
- Memphis Audio
- Nxg
- Mackie
- Tannoy
- PowerBass
- Revel
- Bose
- IMG Stage Line
- JL Audio
- Arcam
- Pyle
- JBL
- SSV Works
- Tangent
- Heco
Nyeste Subwoofer Manualer
28 Juli 2025
27 Juli 2025
27 Juli 2025
27 Juli 2025
27 Juli 2025
26 Juli 2025
24 Juli 2025
24 Juli 2025
24 Juli 2025
23 Juli 2025