Hertz HCP 4D Manual

Hertz Modtager HCP 4D

Læs gratis den danske manual til Hertz HCP 4D (33 sider) i kategorien Modtager. Denne vejledning er vurderet som hjælpsom af 43 personer og har en gennemsnitlig bedømmelse på 4.4 stjerner ud af 22 anmeldelser. Har du et spørgsmål om Hertz HCP 4D, eller vil du spørge andre brugere om produktet?

Side 1/33
SPEAKER BRACKETS
SPM-10TV INSTALLATION MANUAL
Thank you for selecting this Yamaha SPM-10TV speaker mounting brackets. This model is designed specially for use with
Yamaha NS-10MM speaker system.
nPRECAUTIONS
Read the following precautions carefully before mounting
your NS-10MM using these brackets.
Do not use these brackets for mounting speakers other
than NS-10MM.
Mount these brackets on a TV rack etc. firmly by using
commercially available wood screws.
Mount the brackets properly and securely by following this
manual. If the brackets are mounted improperly, they may
fall down and you may be injured.
Use commercially available wood screws which is proper
for using on the board of TV rack. If you use a wood
screw which is longer than the thickness of board and it is
tightened through the board, you may injure yourself in
the hand when you insert a hand into the TV rack.
If your TV is a revolving type, mount the speakers and the
brackets so that they will not touch the TV when the TV is
revolved.
Make sure to place these brackets on a flat surface. If
placed on an uneven surface, they may fall down and you
may be injured.
To avoid accidents resulting from tripping over loose
speaker cables, fix them to the wall.
Do not attempt to clean the brackets with chemical
solvents as this might damage the finish. To clean, wipe
with a dry, soft cloth.
To prevent the brackets from discoloring or being
corroded, do not place the brackets where they will be
exposed to direct sunlight or excessive humidity.
Secure placement or installation is the owner’s
responsibility. YAMAHA shall not be liable for any
accident caused by improper placement or
installation of the brackets.
nACCESSORIES
Pad A x 4
(VV777700)
Pad B x 1
(VV777800)
Hexagonal wrench x 1
(VV778000)
Two-sided tape x 2
(VV876500)
Bolt (diam. 4 mm) x 4
(VB514900)
Washer (diam. 4 mm) x 4
(ET500040, black)
Logo plate x 2
(VV777900)
nMOUNTING SPEAKERS
Notes
Mount the speaker to the bracket so that the speaker
faces the front as figured below.
Make mounting by using the provided bolts and washers.
For tightening bolts, use the provided hexagonal wrench.
Procedure
1. Put the provided pads A on the bracket as figured below.
(Put the pad A carefully. Putting and removing the pad
repeatedly may tear it off.)
2. Before mounting the speaker to the bracket, insert a bolt
and a washer into the hole on the bottom of the speaker
which is closer to the TV, and tighten the bolt to about
80%.
3. Pass the head of the bolt tightened on the speaker
through the hole (marked *on the figure above) on the
bracket, and slide the head of the bolt to the narrow part
of the hole.
4. Mount the speaker to the bracket by inserting a bolt and a
washer into the other hole as figured below.
5. Tighten both bolts fully.
Pad A
*Pad A
Washer
(diam. 4 mm)
Bolt
(diam. 4 mm)
Special for use with NS-10MM
(Right side)


Produkt Specifikationer

Mærke: Hertz
Kategori: Modtager
Model: HCP 4D

Har du brug for hjælp?

Hvis du har brug for hjælp til Hertz HCP 4D stil et spørgsmål nedenfor, og andre brugere vil svare dig




Modtager Hertz Manualer

Modtager Manualer

Nyeste Modtager Manualer

Sommer

Sommer SOMcom1 Manual

9 November 2025
Nady

Nady 351VR HT Manual

9 November 2025
Spedal

Spedal CL786 Manual

8 November 2025
Weuaste

Weuaste Carplay 01 Manual

8 November 2025
Taramp’s

Taramp’s BASS 400 Manual

7 November 2025
Nady

Nady U-1100 Manual

7 November 2025
Taramp’s

Taramp’s MD 8000.1 Manual

6 November 2025
Monoprice

Monoprice 38360 Manual

6 November 2025
Stinger

Stinger MT-700.1 Manual

6 November 2025